Search NASA⌕ Search

Engineering topics

A Scholten

Publications and source records attributed to A Scholten.

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Modal and nonmodal instability characteristics of cylindrically blunted flat plates with varying leading edge radii are described for Mach 4 and Mach 6 freestream conditions. The selection of leading edge radii and freestream parameters is informed by experimental conditions. The investigation of this 2D problem provides a slow entropy layer swallowing which allows for an isolated development of perturbations seeded upstream within different wall-normal regions of the flow. At both Mach numbers, a decrease in modal instability amplification was seen as the leading edge radius was increased. Nonmodal analysis reveals amplifying perturbations in the boundary layer as well as in the entropy layer. The medium bluntness regime exhibits the strongest amplification of nonmodal disturbances that is nonmonotonic in character. Small amplitude boundary forcing at the plate surface or volumetric forcing at various wall-normal heights was used to account for receptivity effects. While wall forcing effectively induced modal instabilities, only an actuation above the boundary layer captured disturbances that amplify within the entropy layer. The optimal nonmodal theory’s entropy-layer disturbance evolution exhibited outstanding agreement with controlled forcing, including receptivity effects. The evolution of entropy-layer disturbances from the optimal nonmodal theory showed excellent agreement with the results of receptivity to controlled forcing. Therefore, the nonmodal optimal growth analysis may provide a useful as well as efficient technique to identify the complete disturbance spectrum in blunt hypersonic configurations, where both modal and nonmodal disturbances can amplify in the boundary-layer and entropy-layer regions.

Boundary layer transition↗
NASA NTRS2022

Combined Bluntness and Roughness Effects on Cones at Hypersonic Speeds

This computational study investigates the effects of discrete roughness elements on a blunt cone at zero degrees angle of attack in a Mach 6 flow. Motivation was provided by experiments conducted in the Air Force Research Laboratory Mach 6 High Reynolds Number facility on a 7-degree half-angle cone with a roughness array located at 45 degrees from the apex on two nose tips of different blutness but equivalent roughness Reynolds number. Transition was only affected on the blunter cone, indicating that the transition onset is associated with the combined effects of bluntness and roughness. The present study investigates the 15.24 mm nose radius, 420 azimuthal wavenumber case via Navier-Stokes computations of the laminar base flow and instability analysis. Plane-marching parabolized stability equations (PSE) and inflow-resolvent analysis based on the three-dimensional, harmonic linearized Navier-Stokes equations (HLNSE) are used to calculate the amplification of disturbances along the roughness wake as well as over the roughness nearfield. Results show that the roughness shape can have a great impact on the characteristics of the most amplified wake instabilities. For the experimental configuration with cubic roughness elements of 15 μ m height, the flow is marginally unstable. For prismatic elements of 20 μ m height, the PSE predicts a logarithmic disturbance amplification ratio of N = 5.6 along its wake, but this ratio increases to N = 9.6 when the amplification over the roughness and separation regions is included in the inflow-resolvent analysis.

Boundary-layer transition↗
NASA NTRS2022

Hypersonic Boundary-Layer Instabilities over Ogive-Cylinder Models

Computational investigations of an ogive-cylinder geometry with varying nosetips at zero degrees angle of attack are presented. The model geometry and conditions are selected to match experiments conducted in the Air Force Research Laboratory (AFRL) Mach 6 Ludwieg Tube. Five nosetips of interest were selected for the computational studies herein: two sharp ogives, two blunt ogives, and one hemispherical nosetip. Computations are performed at a freestream Reynolds number of 7.01 × 10 6 m -1 . Each sharp and blunt tip ogives had a 14 and 28 degree version for the tip angles. A cylindrical section follows the nosetip, resulting in a meter long model such as in the experiments. The laminar flow solutions are analyzed. The boundary-layer-edge properties and the velocity and temperature profiles are compared across streamwise locations aft of the ogive-cylinder junction. The blunt nosetips induce an entropy layer that envelopes the boundary-layer profiles. Modal stability analysis identifies most amplified frequencies corresponding to Mack’s second modes that agree with experimental results for the sharp tips. Similar to the experimental measurements based on wall-mounted pressure sensors, no unstable modes are found for the blunt models. Nonmodal analysis revealed a broadband set of disturbances present for the blunter tips, in agreement with experimental observations. Flow perturbation contours of most amplified planar and oblique disturbances are shown to qualitatively match wind tunnel Schlieren images, with a switch from rope-like to elongated structures, i.e., from high frequency Mack’s second modes to low frequency Mack’s first modes, as the nosetip angle is increased for the sharp tip, and from boundary-layer to entropy-layer disturbances as the bluntness is increased.

Boundary layer transition↗
NASA NTRS2022

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Hydrodynamic instability↗
NASA NTRSDate not supplied

Automatic Boundary-Layer Adaptation of Structured Grids in VULCAN-CFD

In supersonic and hypersonic flow computations, well-resolved boundary layers are essential for accurate quantification of surface heating and transition prediction, particularly via linear stability analysis. Grid design for hypersonic flows with shocks, boundary-layer separation, and/or complex mean flow features incorporating spanwise/azimuthal inhomogeneities is a difficult issue. In comparison to a manual grid adaptation procedure, an autonomous grid adaptation technique offers significant improvements in computing time and solution quality. The VULCAN-CFD solver already includes a validated procedure for automatic adaption of structured grids to the bow shock. The present focus is on implementing an automatic boundary-layer adaptation capability in VULCAN-CFD that adapts structured, multiblock grids to both the bow shock and the boundary layer at the same time. The boundary-layer adaptation algorithm allows the user to specify the number of cells within the boundary layer, along with the input parameters used for detecting the edge of the boundary layer, namely, the variable used in the edge detection criterion,the edge detection method, the detection direction, and the relaxation factor used during the morphing of the grid. The algorithm automatically distributes grid points along the wall-normal direction to achieve a smooth variation in grid spacing from the edge of the boundary layer to a"junction" location within the outer part of the grid. Illustrative results are presented for three different high-speed configurations: the two-dimensional flow over a cylinder at Mach 17.6 and unit Reynolds number of Re=0.38x10^6 m^-1, the axisymmetric flow over a cone-cylinder-flare model at Mach 6.0 and Re = 10.5×10^6 m^-1, and the three-dimensional flow over a blunt, 7-degree half-angle cone at 5-degree angle of attack in a Mach 9.79 flow with Re = 17.1×10^6 m^-1. The automated boundary-layer adaptation is shown to provide an adequate grid topology that is aligned with the bow shock in the outer part of the grid and also resolves the viscous boundary-layer region close to the surface.

boundary layer transition↗
NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

As part of NATO STO AVT-346 “Predicting Hypersonic Boundary-Layer Transition on Complex Geometries,” coordinated experimental and computational studies were conducted on the ROTEX-T, a cone-flare geometry used in a successful flight-test experiment. At the as-flown conditions, a separation bubble existed at the compression corner. Separation, reattachment, and the multifaceted linear instability paths leading this bubble to transition to turbulence are challenging to predict, but have significant impact on surface pressure and heat flux. High-resolution background-oriented schlieren and infrared thermography measurements were made in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel at freestream unit Reynolds numbers from 5.8×10(exp 6) to 12.2×10(exp 6) m-1and nominally zero angle of attack. High-speed self-aligned focusing schlieren, infrared thermography, and focused laser differential interferometry measurements were made in the AFRL Mach-6 Ludwieg Tube from 2.2×10(exp 6) to 24.7×10(exp 6) m-1and nominally zero degrees angle of attack. The surface heat-flux and Stanton number distributions were computed. Separation and reattachment locations, as well as the flow state at each, were determined from the combination of surface and off-wall measurements. The convective and global boundary-layer instabilities of the axisymmetric laminar flow at the experimental conditions were investigated computationally. Amplification of Mack’s first and second modes were observed to have logarithmic amplification factors between 5 to 7.5 at the separation location, depending on conditions. The flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Previous analysis of the ROTEX-T flight data had not assessed reattachment location or the flow state upon reattachment. Thanks to the insights gained from the coordinated, on- and off-wall ground-test measurements, these evaluations have now been made. The separation location indicated by laminar simulations is consistently numerically predicted to be upstream of the experimentally observed location for a transitional separation bubble. The cause of this difference is understood to lie in the steady-state and axisymmetric assumptions made by both solvers employed to compute the basic states analyzed, as flow topology considerations assert that unsteady two-dimensional or axisymmetric separation bubbles are structurally unstable and will become three-dimensional. Computed laminar heating rates prior to separation agreed well with experiment; transitional heating rates after reattachment were between laminar and turbulent computations.

CFD Validation↗