Engineering topics
Abraham, Alyson
Publications and source records attributed to Abraham, Alyson.
Energy dispersive X-ray diffraction (EDXRD) for operando materials characterization within batteries
Explore the source record for details and available documents.
Capacity Retention for (De)lithiation of Silver Containing α-MnO2: Impact of Structural Distortion and Transition Metal Dissolution
Explore the source record for details and available documents.
Silver-Containing α-MnO2 Nanorods: Electrochemistry in Rechargeable Aqueous Zn-MnO2 Batteries
Explore the source record for details and available documents.
Self-Healing, Improved Efficiency Solid State Rechargeable Li/I 2 Based Battery
Solid state electrolytes are receiving significant interest due to the prospect of improved safety, however, addressing the incidence and consequence of internal short circuits remains an important issue. In this study, a battery based on a LiI-LiI(HPN) 2 solid state electrolyte demonstrated self-healing after internal shorting where the cells recovered and continued to cycle effectively. The functional rechargeable electrochemistry of the self-forming Li/I 2 -based battery was investigated through interfacial modification by inclusion of Li metal (at the negative interface), and/or fabricated carbon nanotube substrates at the positive interface. A cell design with lithium metal at the negative and a carbon substrate at the positive interface produced Coulombic efficiencies > 90% over 60 cycles. Finally, the beneficial effects of moderately elevated temperature were established where a 10 °C temperature increase led to ~5× lower resistance.
Ex Situ and Operando XRD and XAS Analysis of MoS2: A Lithiation Study of Bulk and Nanosheet Materials
Explore the source record for details and available documents.
Improved Capacity Retention of Lithium Ion Batteries under Fast Charge via Metal-Coated Graphite Electrodes
A primary barrier preventing repetitive fast charging of Li-ion batteries is lithium metal plating at the graphite anode. One approach toward mitigating Li metal deposition is the deliberate modification of the graphite anode surface with materials demonstrating high overpotentials unfavorable for Li metal nucleation, such as Ni or Cu nanoscale films. This research explores Ni and Cu surface coatings at different areal loadings (3 or 11 μg cm -2 ) on the electrochemistry of graphite/LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) type Li-ion batteries. Extended galvanostatic cycling of control and metal-coated electrodes in graphite/NMC622 pouch cells are conducted under high rate conditions. Based on the overpotential of Li deposition on metal foil, both Ni and Cu treatments were anticipated to result in reduced lithium deposition. The higher metal film loadings of 11 μg cm -2 Ni- or Cu-coated electrodes exhibit the highest capacity retention after 500 cycles, with mean improvements of 8% and 9%, respectively, over uncoated graphite electrodes. Li plating quantified by X-ray diffraction indicates that the metal films effectively reduce the quantity of plated Li compared to untreated electrodes, with 11 μg cm -2 Cu providing the greatest benefit.
A Multimodal Approach to Materials Design for Next Generation Energy Storage Systems
While batteries of various chemistries have been responsible for powering everything from small electronics to cars to medical devices, the need for energy storage continues to increase. This increase is in both volume and in scale, as energy storage systems are increasingly being evaluated for inclusion into both larger and broader applications. An important factor to consider with batteries is the end application, as each chemistry and battery system has specific benefits as well as limitations. This necessitates development of a wide range of battery chemistries as well as substantive improvements to these chemistries and their integration on the material, electrode, and systems level. Herein, this work will present on a multi-scale level, different energy storage studies can that are geared to address the demands and needs of varying applications. To highlight the diversity and uniqueness of the required breadth of approaches, several systems are presented in combination with different characterization techniques and analysis relevant to the system. Highlights include proof of concept and development of a self - forming, rechargeable solid state battery, materials development for Lithium Sulfur (Li-S) batteries, electrochemical and characterization techniques to elucidate materials properties, and utilizing theoretical calculations to compliment experimental observations.
Nanocomposite liposomes for pH-controlled porphyrin release into human prostate cancer cells
Nanocomposite liposomes are relatively stable in weak basic solutions but effectively release porphyrins at acidic pH, as indicated by the difference in fluorescence.
Electrodeposition of MoS x : Tunable Fabrication of Sulfur Equivalent Electrodes for High Capacity or High Power
Not Available
Defect Control in the Synthesis of 2 D MoS 2 Nanosheets: Polysulfide Trapping in Composite Sulfur Cathodes for Li–S Batteries
One of the inherent challenges with Li–S batteries is polysulfide dissolution, in which soluble polysulfide species can contribute to the active material loss from the cathode and undergo shuttling reactions inhibiting the ability to effectively charge the battery. Prior theoretical studies have proposed the possible benefit of defective 2 D MoS 2 materials as polysulfide trapping agents. Herein the synthesis and thorough characterization of hydrothermally prepared MoS 2 nanosheets that vary in layer number, morphology, lateral size, and defect content are reported. Here, the materials were incorporated into composite sulfur–based cathodes and studied in Li–S batteries with environmentally benign ether–based electrolytes. Through directed synthesis of the MoS 2 additive, the relationship between synthetically induced defects in 2 D MoS 2 materials and resultant electrochemistry was elucidated and described.
Progress and Outlook on Few Component Composite Solid State Electrolytes
Lithium solid-state composite electrolytes (LiSCEs) provide the opportunity for long life spans, low self-discharge, high reliability, high energy density, and safety. In addition, this class of electrolytes can be used in electrolytically formed solid-state batteries (EFBs), which may promote reductions in cell manufacturing costs due to their simplicity of design and permit the formation of batteries with diverse architectures. Herein, we provide a discussion of LiSCEs, highlight some of the recent progress in EFB development, and present a forward outlook.
The application of poorly crystalline silicotitanate in production of 225 Ac
Actinium-225 ( 225 Ac) can be produced from a Thorium-229/Radium-225 ( 229 Th/ 225 Ra) generator, from high/low energy proton irradiated natural Thorium or Radium-226 target. Titanium based ion exchanger were evaluated for purification of 225 Ac. Poorly crystalline silicotitanate (PCST) ion exchanger had high selectivity for Ba, Ag and Th. 225 Ac was received with trace amounts of 227 Ac, 227 Th and 223 Ra, and the solution was used to evaluate the retention of the isotopes on PCST ion exchanger. Over 90% of the 225 Ac was recovered from PCST, and the radiopurity was >99% (calculated based on 225 Ac, 227 Th, and 223 Ra). The capacity of the PCST inorganic ion exchange for Barium and 232 Th was determined to be 24.19 mg/mL for Barium and 5.05 mg/mL for Thorium. PCST ion exchanger could separate 225 Ac from isotopes of Ra and Th, and the process represents an interesting one step separation that could be used in an 225 Ac generator from 225 Ra and/or 229 Th. Capacity studies indicated PCST could be used to separate 225 Ac produced on small 226 Ra targets (0.3–1 g), but PCST did not have a high enough capacity for production scale Th targets (50–100 g).
High capacity vanadium oxide electrodes: effective recycling through thermal treatment
This study demonstrates that thermal regeneration is an effective approach to convert degraded phases to functioning electroactive materials, restore functional delivered capacity and recover material crystallinity while retaining the integrity of the parent electrode. V 2 O 5 nanowires were synthesized through a facile hydrothermal method and used to fabricate V 2 O 5 /carbon nanotube (CNT) binder free electrodes. Discharge of the V 2 O 5 –CNT electrodes coupled with operando energy dispersive X-ray diffraction shows no evidence of phase segregation throughout the 150 μm thick binder free electrodes indicating full utilization of a thick electrode. When V 2 O 5 is highly electrochemically lithiated (x > 2 in LixV 2 O 5 ), irreversible phase transformation to ω-LixV 2 O 5 was observed, accompanied by a capacity decrease of ~40% over 100 cycles. A simple thermal treatment of the entire electrode results in a delivered capacity equal to or higher than the original value. Both phase conversion and an increase in material crystallinity as a result of thermal treatment are observed where structural analysis indicates the formation of Li 1 V 3 O 8 . The electrode design approach with thick electrodes and functional thermal regeneration may provide a broader choice of electroactive materials through decreasing the environmental burden by extending the lifetime of energy storage systems.
Deliberate Modification of Fe 3 O 4 Anode Surface Chemistry: Impact on Electrochemistry
Fe 3 O 4 nanoparticles (NPs) with an average size of 8-10 nm have been successfully functionalized with various surface-treatment agents to serve as model systems for probing surface chemistry-dependent electrochemistry of the resulting electrodes. The surface-treatment agents used for the functionalization of Fe 3 O 4 anode materials were systematically varied to include aromatic or aliphatic structures: 4-mercaptobenzoic acid (MBA), benzoic acid (BA), 3-mercaptopropionic acid (MPA), and propionic acid (PA). Both structural and electrochemical characterizations have been used to systematically correlate the electrode functionality with the corresponding surface chemistry. Surface treatment with ligands led to better Fe 3 O 4 dispersion, especially with the aromatic ligands. Electrochemistry was impacted where the PA and BA-treated Fe 3 O 4 systems without the -SH group demonstrated higher rate capability than their thiol-containing counterparts and the pristine Fe 3 O 4 . Specifically, the PA system delivered the highest capacity and cycling stability amongst all samples tested. Notably, the aromatic BA system outperformed the aliphatic PA counterpart during extended cycling under high current density, due to the improved charge transfer and ion transport kinetics as well as better dispersion of Fe 3 O 4 NPs, induced by the conjugated system. Our surface engineering of the Fe 3 O 4 electrode presented herein, highlights the importance of modifying the structure and chemistry of surface-treatment agents as a plausible means of enhancing interfacial charge transfer within metal oxide composite electrodes without hampering the resulting tap density of the resulting electrode.
Interface effects on self-forming rechargeable Li/I 2 -based solid state batteries
Solid state batteries are an emerging alternative to traditional liquid electrolyte cells that provide potential for safe and high-energy density power sources. This report describes a self-forming, solid state battery based on the Li/I 2 couple using an LiI-rich LiI(3-hydroxypropionitrile) 2 electrolyte (LiI–LiI(HPN) 2 ). As the negative and positive active materials are generated in situ, the solid electrolyte–current collector interfaces play a critical role in determining the electrochemical response of the battery. Furthermore, we report the investigation of solid electrolyte–current collector interfaces with a self-forming LiI–LiI(HPN) 2 solid electrolyte and the role of varying interface design in reducing resistance during cycling.
Toward Environmentally Friendly Lithium Sulfur Batteries: Probing the Role of Electrode Design in MoS 2 -Containing Li–S Batteries with a Green Electrolyte
While lithium sulfur batteries (Li–S) hold promise as future high energy density low cost energy storage systems, barriers to implementation include low sulfur loading, limited cycle life, and the use of toxic electrolyte solvents. A comprehensive study of Li–S cells in the environmentally benign di(propylene glycol) dimethyl ether (DPGDME)-based electrolyte, using as-prepared MoS 2 nanosheets derived from a facile aqueous microwave synthesis as polysulfide trapping agents, is reported herein for the first time. Conventional coated foil electrodes and binder-free electrodes (BFEs) with various structures are systematically generated and tested to correlate electrode design with the resulting electrochemical behavior. Significantly improved Li–S electrochemistry is demonstrated through the synergy of MoS 2 chemistry and binder-free electrode engineering. In the coating configuration, the MoS 2 -containing cell evinced better rate performance and more stable cyclability than the cell without MoS 2 . In comparison with the coating counterparts, the BFE cells exhibited excellent cycle stability and superior rate capability (10-fold capacities and energy density per electrode weight with 20% higher retention rate) despite 2X higher areal sulfur loading. As a result, the BFE cell improvement can be attributed to the synergistic effect of the i) interconnected macroporous structure of CNT interlayers, providing a conductive framework, and ii) the efficient polysulfide trapping by the MoS 2 nanosheets.
Investigation of Conductivity and Ionic Transport of VO 2 (M) and VO 2 (R) via Electrochemical Study
Vanadium dioxides exist as a variety of polymorphs, each with differing structural and electrochemical capabilities. The monoclinic to rutile transition is an interesting system for study as the transition temperature is easily accessible at moderate temperature and corresponds to an increase in electrical conductivity by two orders of magnitude. The transition from monoclinic to rutile is characterized structurally herein using synchrotron-based x-ray diffraction and related to lithium ion electrochemistry using electrochemical impedance spectroscopy and intermittent pulsatile galvanostatic discharge tests. The experimental results indicate a decrease in ohmic resistance for lithium-based cells tested under higher temperatures. Complementary density functional theory calculations described the experimentally measured intercalation voltages and identified a possible Li-induced Li x VO 2 (M) to Li x VO 2 (R) phase transition during the discharging process rationalizing the favorable impact on the function of a lithium based electrochemical cell. Here, to our knowledge, this is the first observation of the metal—insulator transition of VO 2 in a full electrochemical cell.