Search NASA⌕ Search

Engineering topics

Abrams, T. (ORCID:0000000296056871)

Publications and source records attributed to Abrams, T. (ORCID:0000000296056871).

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Experiments on plasma detachment in a V-shaped slot divertor in the DIII-D tokamak

Abstract Experiments in DIII-D demonstrate that the upstream plasma density to detach an un-pumped slot divertor is similar for a V-shaped and a flat-end slot, despite significantly higher neutral pressure in the V-shaped slot and in contrast to SOLPS-ITER predictions. The detachment threshold can be reduced by using in-slot instead of main-chamber gas fuelling or by placing the strike point on the inner slanted slot baffle instead of the slot end, as described by simulations with full drift physics. When increasing the plasma line-averaged density (without extrinsic impurities), the transition to detachment in DIII-D slot divertor is sharp and requires a high value of plasma density with the ion B → × ∇ B drift into the slot, whereas it is smooth and requires a lower value of plasma density with the opposite drift direction, in accord with detachment experiments in the DIII-D open lower divertor. Unique experiments on DIII-D and comparison to advanced simulations expand the scientific understanding of slot-shaped divertors, considered highly desirable for next step fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Comprehensive new insights on the potential use of SiC as plasma-facing materials in future fusion reactors

Abstract The performance of silicon carbide as an alternative plasma facing material (PFM) was studied at various irradiation conditions relevant to ion energies and fluxes of a fusion reactor. This analysis involves detailed modeling of subsurface plasma/material interactions, sputtered particle transport above the surface and redeposition, and related changes in material composition and microstructure induced by steady-state and Edge Localized Mode ion fluxes. Transition of a crystalline SiC surface to semi-crystalline and amorphous phases was analyzed based on advanced modeling of DIII-D tokamak experiments where SiC was irradiated in single- and multiple- L-mode and H-mode discharges. This analysis shows that displacement damage, particle deposition/redeposition, and D accumulation on the SiC divertor surface can lead to significant microstructural changes that result in enhanced sputtering erosion in comparison with the original crystalline material. However, the resulting total net erosion rate for a full-coverage, advanced tokamak, SiC coated divertor may well be acceptably low. Moreover, the C sputtering yield from the evolved SiC surface can be seven times lower than from a pure graphite surface; this would imply significantly reduced tritium co-deposition rates in a D-T tokamak reactor, compared with a pure carbon surface. It was also determined that chemical sputtering of both C and Si should not result in any noticeable effect on the net erosion, for attached plasma regimes. Our results thus show encouraging results overall for use of SiC as a PFM in tokamaks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

DIII-D's role as a national user facility in enabling the commercialization of fusion energy

The path to fusion in the United States requires partnership between public and private sector. While the private sector provides the vigor to take some of the major steps necessary, there is a depth of expertise and capability in the public sector that is vital to resolving feasible approaches. As an open national user facility, DIII-D provides a crucial testbed to develop the required new technologies and approaches in relevant conditions. It has unparalleled potential to meet this challenge, thanks to its extreme flexibility and world leading diagnostics. This provides a basis to rapidly develop solutions that project to future reactors with confidence. The program has thus been redeveloped to enable public and private sector engagement and testing of new concepts. A new technology program has been launched to resolve plasma interacting technologies. With modest heating upgrades, the facility can confront the crucial “Integrated Tokamak Exhaust and Performance” gap, to resolve core, exhaust and technology solutions together. The device is also being redeveloped as a training facility, with dedicated student run time, a mentorship program, and open access to all opportunity roles, part of wider efforts to diversify and open pathways through inclusion, access, and equity. This exciting agenda is enabling scientists and technology researchers to pioneer the solutions needed for a Fusion Pilot Plant (FPP) and ITER this decade. As a national user facility, DIII D has singular potential to provide the tools, teams, and insight necessary, to do its part in moving the United States rapidly toward the commercialization of fusion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Recent DIII-D progress toward validating models of tungsten erosion, re-deposition, and migration for application to next-step fusion devices

Abstract Fundamental mechanisms governing the erosion and prompt re-deposition of tungsten impurities in tokamak divertors are identified and analyzed to inform the lifetime of tungsten plasma-facing components in ITER and other future devices. Various experiments conducted at DIII-D to benchmark predictive models are presented, leveraging the DiMES removable sample exposure probe capability and the Metal Rings Campaign, in which toroidally symmetric rows of tungsten-coated tiles were installed in the DIII-D divertor. In tokamak divertors, the width of the electric sheath is of the order of the main ion Larmor radius, and a vast majority of sputtered tungsten impurities are typically ionized within the sheath. Therefore, W prompt redeposition is mainly governed by the ratio of the characteristic ionization mean-free path of neutral tungsten to the width of the sheath. In-situ monitoring of the prompt redeposition of tungsten impurities in divertors is demonstrated via the use of WII/WI line ratios and the ionizations/photon (S/XB) method in L-mode discharges. Even with this relatively limited set of emission measurements, net erosion measurements were found to be a consistent upper bound to an analytic scaling based on the ratio of the W ionization length, λ iz , and the width of the magnetic sheath rather than the ratio of λ iz and the W + gyro-radius. In the far-scrape-off layer (SOL) of the ITER divertor, however, it is calculated that the measurement of photon emissions associated with the ionization of tungsten impurities up to W 5 + may be required. Finally, W deposition patterns on DiMES collector probes, interpreted via DIVIMP-WallDYN modelling, reveal the key roles of progressive W erosion/re-deposition staps and E × B drifts in regulating long-range high-Z material migration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Abstract Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from 3.9– 7.5 × 10 19 m −3 and input powers ranging from 5.5 to 9 MW. The small Si pellets were delivered with the impurity granule injector at frequencies ranging from 4 to 16 Hz corresponding to mass flow rates of 5–19 mg s −1 (1– 4.2 × 10 20 Si s −1 ) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO 2 is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least 0.4–1.2 nm thickness have been deposited at 0.4–0.7 nm s −1 . The technique is estimated to coat a surface area of at least 0.94 m 2 on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

The effectiveness of D 2 pellet injection in reducing intra-ELM and inter-ELM tungsten divertor erosion rates in DIII-D during the Metal Rings Campaign

Abstract Edge localized modes (ELMs) in H-mode plasmas erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes D 2 pellet injection on the DIII-D fusion experiment used as an ELM mitigation technique applied during the 2016 tungsten Metal Rings Campaign to reduce W erosion during ELMs. The 400.9 nm photon wavelength line emission intensity of tungsten atoms (WI) filterscope channels and Langmuir probes were used to infer the gross erosion rate of tungsten-coated tiles installed in the divertor of DIII-D. D 2 mass injection rates ranging from 34 to 41 arbitrary units (A.U.) and no D 2 injection resulted in a similar total W erosion rate during ELMs (intra-ELM). On average, results show a 29% increase in the total gross W erosion rate with intermediate mass injection rates (∼13–23 A.U.) compared to the no pellets and the highest injection rate cases. On average, the fast D 2 mass injection rate cases had 15% less erosion in the inter-ELM phase than the case with no pellets. Generally, higher D 2 mass injection rates increased the ELM frequency, and the highest injection rates reduced the average erosion per ELM and fractional carbon impurities at the top of the pedestal by nearly 40% when compared to the no-pellet case. As expected, a higher D 2 pellet injection rate led to a higher plasma density and lower plasma temperature in the divertor. Additionally, an increasing divertor inter-ELM plasma electron density directly correlated to more frequent pellet injection and a decrease in both the average gross intra-ELM W erosion and the total gross intra-ELM W erosion rate. Simulations of intra-ELM erosion using the ‘free-streaming plus recycling model’ (FSRM) underestimate W erosion during pellet injection by about 30% on average. The discrepancies between the experimental measurements and the FSRM intra-ELM W erosion predictions are postulated to be due to C/W material mixing. A simple analytic mixed-material model is presented and results in better agreement with the experimental data. These results highlight the importance of incorporating the effects of a mixed-material layer in the analysis of PFC erosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy

DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L–H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ~8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part A: concepts and questions

Abstract It is estimated that pilot plants and reactors may experience rates of net erosion and deposition of solid plasma facing component (PFC) material of 10 3 –10 5 kg yr −1 . Even if the net erosion (wear) problem can be solved, the redeposition of so much material has the potential for major interference with operation, including disruptions due to so-called ‘unidentified flying objects (UFOs)’ and unsafe dust levels. The potential implications appear to be no less serious than for plasma contact with the divertor target: a dust explosion or a major UFO-disruption could be as damaging for an actively-cooled deuterium-tritium (DT) tokamak as target failure. It will therefore be necessary to manage material deposits to prevent their fouling operation. This situation appears to require a fundamental paradigm shift with regard to meeting the challenge of taming the plasma–material interface: it appears that any acceptable solid PFC material will in effect be flow-through , like liquid–metal PFCs, although at far lower mass flow rates. Solid PFC material will have to be treated as a consumable , like brake pads in cars. ITER will use high-Z (tungsten) armor on the divertor targets and low-Z (beryllium) on the main walls. The ARIES-AT reactor design calls for a similar arrangement, but with SiC cladding on the main walls. Non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for the main walls, while reducing the risk of degrading the confined plasma. Separately, wall conditioning has proven essential for achieving high performance. For DT devices, however, standard methods appear to be unworkable, but recently powder droppers injecting low-Z material ∼continuously into discharges have been quite effective and may be usable in DT devices as well. The resulting massive generation of low-Z debris, however, has the same potential to seriously disrupt operation as noted above. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in all current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part B: required research in present tokamaks

Abstract The companion part A paper (Stangeby et al 2022) reports a number of independent estimates indicating that high-duty-cycle DT tokamaks starting with pilot plants will likely experience rates of net erosion and deposition of solid PFC, plasma facing component, material in the range of 10 3 to 10 4 kg yr −1 , regardless of the material used. The subsequent redeposition of such large quantities of material has the potential for major interference with tokamak operation. Similar levels and issues will be involved if ∼continuous low-Z powder dropping is used for surface conditioning of DT tokamaks, independent of the material used for the PFC armor. In Stangeby et al (2022) (part A) it is proposed that for high-duty-cycle DT tokamaks, non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for protecting the main walls, while reducing the risk of degrading the confined plasma. Assessment of whether such an approach is viable will require information, much of which is not available today. Section 6 of part A identifies a partial list of major physics questions that will need to be answered in order to make an informed assessment. This part B report describes R&D needed to be done in present tokamaks in order to answer many of these questions. Most of the required R&D is to establish better understanding of low-Z slag generation and to identify means to safely manage it. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗