Engineering topics
Publications and source records attributed to Abu-Omar, Mahdi M..
Lignin-based syringol monomer, 2,6-dimethoxypropylphenol (DMPP), can be upgraded through two synthetic routes to multi-functional propylpyrogallol DMPPO and tri-epoxide which allows for various polymer applications.
Polymers of ethylene and copolymers of ethylene and 1-hexene are synthesized by utilizing a single-site hafnium catalyst activated with tris(pentafluorophenyl)borane. Polymer production increases sharply as compared to the homopolymerization of ethylene with the addition of just a small amount of 1-hexene-a phenomenon known as the "comonomer effect." A mechanism behind the comonomer effect is proposed where the activation-initiation step plays the key part. When only a small fraction of the precatalyst is initially active, high molecular weight (170 000 g mol -1 , Đ 1.6) polymer chains grow, forming a physical gel structure that traps catalyst, monomer, and solvent molecules, thereby shutting down the reaction-this scenario plays out in the case of homopolymerization of ethylene. 1-Hexene, when present, slows down the chain growth, thereby lowering the molecular weight and preventing the formation of a gel, which in turn allows for more catalytic sites to be initiated; the reaction continues, resulting in a larger amount of polymer of lower molecular weight (25 000 g mol -1 ). The proposed mechanism is validated in a series of experiments where targeted variation of the activation/initiation steps is shown to produce, depending on the condition, either a small amount of high molecular weight physical gel or a large amount of low molecular weight polymer.
Non-edible lignocellulosic biomass represents the most abundant source of renewable carbon on Earth. To harness its potential for producing valuable fuels and building blocks for renewable plastics, it is essential to undergo a process that involves the removal of oxygen atoms from its components. This report outlines various methodologies aimed at converting biomass components into fuels and building blocks suitable for renewable plastics. The primary emphasis of the described research lies in leveraging sustainable chemistry and catalysis to valorize biomass into fuels and chemicals.
Supported platinum nanoparticle catalysts are known to convert polyolefins to high-quality liquid hydrocarbons using hydrogen under relatively mild conditions. To date, few studies using platinum grafted onto various metal oxide (M x O y ) supports have been undertaken to understand the role of the acidity of the oxide support in the carbon-carbon bond cleavage of polyethylene under consistent catalytic conditions. Specifically, two Pt/M x O y catalysts (M x O y = SrTiO 3 and SiO 2 -Al 2 O 3 ; Al = 3.0 wt %, target Pt loading 2 wt % Pt similar to 1.5 nm), under identical catalytic polyethylene hydrogenolysis conditions (T = 300 degree celsius, P(H 2 ) = 170 psi, t = 24 h; M w = similar to 3,800 g/mol, M n = similar to 1,100 g/mol, D = 3.45, N branch/100C = 1.0), yielded a narrow distribution of hydrocarbons with molecular weights in the range of lubricants (M w = < 600 g/mol; M n < 400 g/mol; D = 1.5). While Pt/SrTiO 3 formed saturated hydrocarbons with negligible branching, Pt/SiO 2 -Al 2 O 3 formed partially unsaturated hydrocarbons (<1 mol % alkenes and similar to 4 mol % alkyl aromatics) with increased branch density (N branch/100C = 5.5). Further investigations suggest evidence for a competitive hydrocracking mechanism occurring alongside hydrogenolysis, stemming from the increased acidity of Pt/SiO 2 -Al 2 O 3 compared to Pt/SrTiO 3 . Additionally, the products of these polymer deconstruction reactions were found to be independent of the polyethylene feedstock, allowing the potential to upcycle polyethylenes with various properties into a value-added product.
A thermoset precursor composition includes a backbone comprising an imine bond bonding at least one of: 1) aromatic compounds together, or 2) bonding an aromatic compound to an aliphatic chain, and at least one of: an epoxy group terminating the backbone or an aldehyde group terminating the backbone. The thermoset precursor can have at least two epoxy groups, one epoxy group and one aldehyde group, or two aldehyde groups.
Presented here is an overview of progress in one approach to reducing greenhouse gas emission, namely substituting photosynthesis generated, woody biomass for fossil carbon as feedstock in the production of chemicals and liquid fuels.
Depolymerization and upcycling are promising approaches to managing plastic waste. However, quantitative measurements of reaction rates and analyses of complex product mixtures arising from depolymerization of polyolefins constitute significant challenges in this emerging field. Here, we detail techniques for recovery and analysis of products arising from batch depolymerization of polyethylene. We also describe quantitative analyses of reaction rates and products selectivity. This protocol can be extended to depolymerization of other plastics and characterization of other product mixtures including long-chain olefins. For complete details on the use and execution of this protocol, please refer to Sun et al.
Catalytic conversion of waste polyolefins to value-added alkylaromatics could contribute to carbon recycling. Compared with tandem hydrogenolysis/aromatization of polyethylene (PE) catalyzed by Pt/γ-Al 2 O 3 at 280°C, both a 5-fold enhancement in the rate of C–C bond scission and a doubling of the molar yield of alkylaromatics were achieved using a more acidic Pt/F-Al 2 O 3 catalyst instead. Bifunctional (metal/acid) catalysts also generate alkylaromatic products with lower average carbon numbers (ca. C 20 ), similar to conventional anionic surfactants. Because physical mixtures of weakly acidic Pt/γ-Al 2 O 3 or non-acidic Pt/SiO 2 with strongly Brønsted acidic Cl-Al 2 O 3 or F-Al 2 O 3 are also effective, the tandem reaction does not require nanoscale intimacy between metal and acid active sites. Kinetic studies using triacontane (norm-C 30 H 62 ) as a model for PE show that the Pt-catalyzed dehydrogenation/hydrogenation reactions are quasi-equilibrated, while the acid-catalyzed C–C bond scission and skeletal transformations (isomerization and cyclization) determine the overall rates of depolymerization and aromatic formation.
The production of adipic acid, a large-volume platform chemical, from biomass represents a petroleum-free route to manufacturing nylon and other polymers more sustainably. In this study, a one-step conversion of bioderived mucic acid to adipates is reported over a heterogeneous, bifunctional Ir–ReO x /C catalyst via deoxydehydration (DODH) and catalytic transfer hydrogenation (CTH) using isopropanol as a green solvent and reductant. With very low Ir content (0.05 wt%), the catalyst provides a low-cost option for the tandem DODH–CTH process, while still enabling reuse and regeneration for at least five cycles. The reported catalytic system generates adipates in good yield (63%) without the need for additives (acids or halogens) or high pressure H 2 . Through model reactions and spectroscopic analyses, a bifunctional DODH–CTH mechanism was supported, with the Re VI/IV redox pair as the active DODH species and Ir0 saturating the dialkene intermediate via CTH. Thermal treatment in catalyst preparation and regeneration was optimized to limit metal leaching while maintaining good activity. Further, the present work outlines a one-step deoxygenation of an aldaric acid substrate from biomass using a bimetallic catalyst of low noble metal content to an important monomer for the polymer industry. This system facilitates use in future syntheses of sustainable chemicals from renewable oxygenates where the catalyst is reusable and affordable.
More than 40 million tons of thermosetting plastics are produced annually and 70% of those are epoxy polymers. The synthesis of bio-based epoxide provides a pathway for making renewable thermoset plastics. We describe in this study the use of a genetically modified high-S poplar lignin to produce 4-propyl-2,6-dimethoxyphenol (DMPP), which is converted to the tri-functional compound propylpyrogallol (DMPPO) by a reaction catalysed by N 2 O 5 in the green solvent water. The resulting DMPPO can be converted to a novel tri-epoxide by reaction with epichlorohydrin. Native high-S lignin as well as several organosolv lignins extracted from this poplar biomass were investigated as feedstocks. Notably, direct reductive catalytic fractionation (RCF) of the high-S poplar wood over Pd–Zn/C catalyst with Pd : Zn ratio 1 : 10 at 225 °C under 35 bar H 2 in methanol gave the highest yield of biophenol monomers from the lignin present, the major product being DMPP. Under optimized conditions, conversion of DMPP to DMPPO over the Nb 2 O 5 was nearly quantitative (96% yield), and this conversion could be made without extensive prior purification of the DMPP. The Nb 2 O 5 catalyst could be recycled several times before significant deactivation. This sequence of two catalytic reactions demonstrates that the production of epoxides from lignin-derived DMPPO is a realistic strategy for making renewable polymer building blocks from biomass.
Not provided.
Direct lithium extraction via membrane separations has been fundamentally limited by lack of monovalent ion selectivity exhibited by conventional polymeric membranes, particularly between sodium and lithium ions. Recently, a 12- Crown-4-functionalized polynorbornene membrane was shown to have the largest lithium/sodium permeability selectivity observed in a fully aqueous system to date. Using atomistic molecular dynamics simulations, we reveal that this selectivity is due to strong interactions between sodium ions and 12-Crown-4 moieties, which reduce sodium ion diffusivity while leaving lithium ion mobility relatively unaffected. Furthermore, the ion diffusivities in the membrane, when scaled by their respective solution diffusivities and free ion fractions, can be collapsed to an almost universal relationship depending on solvent volume fraction.
Significance Lithium is a key ingredient in batteries, which are integral components of next-generation automobiles, airplanes, grid energy storage, and electronic devices. Unfortunately, lithium extraction from natural sources is laborious, slow, and costly, motivating the search for more efficient isolation techniques. While polymeric membranes could reduce the cost of lithium recovery, current membrane materials lack sufficient lithium-ion selectivity. To address this challenge, we introduce a class of polymeric membranes that incorporate ion binding sites, which significantly increases the transport selectivity of LiCl over NaCl. These studies provide guidelines and practical considerations for incorporating specific interactants into polymers that mediate selective ion transport.
With these guidelines, we aim to unite the lignin-first biorefining research field around best practices for performing or reporting feedstock analysis, reactor design, catalyst performance, and product yields.
Lignin is the second most abundant biopolymer and the main source of aromatic structures on earth. Lignin has long been produced as a byproduct of the pulping process and utilized in low value-added applications like heat. However, lignin has received increased attention in recent years to improve its value through various chemical processes. This Review compiles recent progress in synthesis, properties, and applications of lignin-based materials. The lignin for material applications can often be classified into three categories: technical bulk lignin (TBL), lignin-derived oligomers (LDOs), and lignin-derived phenols (LDPs). Furthermore, this Review focuses on the chemical modifications of TBLs and their applications in novel smart materials like self-healing, stimulus responsive, and shape memory polymers. The conversion of TBL to polymers can be briefly divided into two steps: (1) introduction of polymerizable functional groups into the lignin backbone and (2) polymerization that achieves desired materials. Both lignin functionalization and polymerization approaches are discussed in detail. As such, this work attempts to provide a comprehensive overview that highlights the importance of these approaches for the utilization of the abundant but largely ignored biopolymer.
Hydrogenation of succinic acid and maleic acid produces C4 value-added chemicals such as γ-butyrolactone and tetrahydrofuran. Here, unsupported ReOx nanoparticles transform succinic acid to γ-butyrolactone and tetrahydrofuran via catalytic transfer hydrogenation with isopropanol as a liquid phase hydrogen donor. This catalyst is also active for the sequential reaction of deoxydehydration and transfer hydrogenation in isopropanol, synthesizing renewable succinic acid and its esters from tartaric acid. One-step conversion of tartaric acid to γ-butyrolactone is achieved in a moderate yield and the possible reaction pathway is discussed.
The current scale of plastics production and the accompanying waste disposal problems represent a largely untapped opportunity for chemical upcycling. Tandem catalytic conversion by platinum supported on γ-alumina converts various polyethylene grades in high yields (up to 80 weight percent) to low-molecular-weight liquid/wax products, in the absence of added solvent or molecular hydrogen, with little production of light gases. The major components are valuable long-chain alkylaromatics and alkylnaphthenes (average ~C 30 , dispersity Ð = 1.1). Coupling exothermic hydrogenolysis with endothermic aromatization renders the overall transformation thermodynamically accessible despite the moderate reaction temperature of 280°C. This approach demonstrates how waste polyolefins can be a viable feedstock for the generation of molecular hydrocarbon products.
A physical mixture of Ru/C and Nb 2 O 5 is an effective catalyst for upgrading lignin monomers under low H 2 pressure at 250 °C to a clean cut of hydrocarbon liquid fuels. The reaction solvent is water with a small amount of methanol additive. Hydrodeoxygenation (HDO) was evaluated using dihydroeugenol (DHE) as an exemplary lignin monomer model. Under optimized conditions, 100% conversion of DHE and very high selectivity to propyl cyclohexane (C9 hydrocarbon) was achieved. Nb 2 O 5 was prepared at a low temperature (450 °C) and was shown to contain acid sites that enhance the production of fully deoxygenated products. The methanol additive serves as a hydrogen source for the Ru/C catalysed reduction of the aromatic ring. In addition, when a substrate mixture of DHE, isoeugenol and 4-allylsyringol simulating lignin products was employed, 100% conversion to propyl cyclohexane (76%) and propyl benzene (24%) was observed, thereby suggesting the general applicability of this catalyst system for funneling lignin monomers into a clean cut of hydrocarbon liquid fuels. This study sheds light on the function of each catalyst component and provides a simple and green utilization of biomass monomers as a feedstock for renewable hydrocarbon fuels.