Prediction of Ni-based alloy microstructure in wire arc additive manufacturing from cellular automata model
Not provided.
Materials Science↗
Engineering topics
Acharya, Ranadip
Publications and source records attributed to Acharya, Ranadip.
Development of HPC based phase field simulations tool for modification of alloy morphology to enhance material properties during additive manufacturing (AM) process
Currently, additive manufacturing (AM) technology is extensively used to manufacture aerospace components because of the unique advantages of the technique in producing custom designs, complex geometries in a near-net fashion that significantly reduces the manufacturing cost, and improved energy efficiency. However, the thermodynamic properties of existing aerospace alloys and the thermal conditions that prevail in most of the powder-bed based additive manufacturing processes lead to undesirable columnar / columnar-dendritic microstructures that promote solidification cracking during the process, and the development of anisotropy in the mechanical properties of the as-built components. Time consuming, energy-intensive post AM treatments are required to recover the mechanical properties of the wrought components for which the existing alloy compositions were designed for. However, novel alloy compositions, that exploit the AM thermal conditions to produce fine, equiaxed grain structures in the as-built condition, with mechanical properties equal to or exceeding those of the wrought work-horse alloy, Ti-6Al-4V has recently been demonstrated in Ti-Cu alloys. Significant energy savings up to 66% can be obtained for a typical aerospace component through digitally designing the AM process, process parameters, and alloy composition. The current project focused on developing a fundamental understanding of the evolution of the columnar to equiaxed transition (CET) occurring during solidification under AM thermal conditions in Ti-Cu and Ti-Cu-X alloys using high-fidelity phase field (PF) simulations using the leadership class computing facilities that exist in the national laboratories. The simulations were able to capture the effect of alloy and process conditions on CET, and clearly showed the beneficial effect of a ternary solute addition to Ti-Cu binary alloys on CET. The simulations indicated that bulk nucleation in the liquid ahead of the solidifying epitaxial front was promoted by a large, transient, thermal undercooling promoted by the mismatch between the growth rate of the dendrite tips in the epitaxial front and the imposed solidification rate. AM experiments performed at Raytheon Technologies Research Center using the same thermal conditions used in the PF simulations indicated the formation of equiaxed grains, although the grain size was bigger than the ones reported in the literature. On the other hand, the equiaxed grain size predicted by PF simulations were smaller than the grain size of Ti-Cu alloys reported in the literature. The industry will follow up the existing work in a future program that would involve further optimization of the process for the Ti-Cu-X alloys to demonstrate the application of the process and the alloy to a specific aerospace component.
36 MATERIALS SCIENCE↗
Predictive Tools for Customizing Heat Treatment of Additively Manufactured Aerospace Components
Laser-bed powder fusion (LBPF) additive manufacturing is increasingly being used to produce components of complex geometries using the Ni-base superalloy Inconel 718. The composition and the microstructure of the alloy are currently well optimized for wrought components made using conventional manufacturing processes such as rolling, forging, extrusion, etc. The attractive mechanical properties of the alloy result from the underlying austenitic matrix with fine equiaxed grains, and a high density and uniform distribution of the precipitation hardening phase, γ". Heat treatment steps such as homogenization, solutioning and aging are well documented for the wrought alloy. However, when the same wrought alloy compositions are used for the additive manufacturing (AM) processes, the asprocessed microstructure is significantly different, because of the different thermal history associated with LBPF, including rapid solidification and multiple temperature excursions that lead to multiple re-melting and reheating in the solid state. Rapid solidification introduces potential non-equilibrium effects at the moving solid-liquid interfaces that impact the extent of solute segregation, as well as the morphology of the dendritic grains that form. In order to recover the target mechanical properties, AM components have to undergo post-process heat treatments. However, such heat treatments have to be custom designed for the AM process and the component geometry because of the expected vast differences in the microstructure at various locations of a component with complex geometry. The homogenization and precipitation steps should be optimized for the component so that target mechanical properties can be obtained throughout the part. The objective of this research is to utilize High Performance Computing in phase field simulations of microstructure evolution during post-processing of AM components. The physics-based modeling will be beneficial in reducing the experimental effort required for heat treatment process selection, optimization, and certification, thus leading to a significant reduction in energy consumption for AM and post-processing heat treatment. The optimization study will help identify heat treatments steps that are critical for development of a final desired microstructure with the minimum energy input. This combined with shortening of the production cycle (time-to-market) by reducing the number of failed parts (property targets), and reduction in the number of iterations for process optimization, will enable 30-40% savings in the energy costs. Phase field simulations of the degree of homogenization and the effect of local matrix composition on the nucleation and growth of competing precipitating phases were performed using the Microstructure Evolution Using Massively Parallel Phase Field Simulations code developed in-house at the Oak Ridge National Laboratory. The simulations were able to successfully capture the kinetics of nucleation and growth, and morphologies of various precipitating phases as a function of local matrix compositions and composition gradients characteristic of local microstructures arising from location-dependent variations in the thermal conditions. Future work will involve extending the simulations to a length scale consisting of multiple dendrites, so that the effect of homogenization on the coarsening of the dendrites can be simulated and used as an additional input to the optimization of the heat treatment process.
36 MATERIALS SCIENCE↗
Optimization of WAAM Process to Produce AUSC Components with Increased Service Life
Additive manufacturing has the potential to revolutionize industrial hardware and unlock efficiency gains through the fabrication of geometries and architectures not possible by conventional processing. Wire Arc Additive manufacturing (WAAM) process is a class of directed energy deposition process enabling higher build rate and allowing custom wire feedstock allowing spatial variation of microstructure. The larger spot size and lower speed creates a larger melt pool, reducing residual stress and often time creating directional/columnar microstructure for Ni-superalloy. The use of flexible platform provides freedom in deposition strategy, which can accommodate complex substrates, including feature addition onto existing structures, non-flat layers, and repair methods. However, the certification of the final component needs to match the strength requirement. Hence, the quality of the component produced is stringently monitored to avoid buildup of residual stress, cracks, porosity and to reduce detrimental segregated phases commonly observed during alloy solidification. Simulation plays a huge role in predicting the melt pool dimension and can be used to optimize the process parameter. Similar development is also required to perform physics-based modeling of microstructural development in WAAM that can predict the microstructural features during solidification and can be used to optimize the process more effectively. To move toward this goal, Raytheon Technologies Research Center together with Siemens worked to create a set of computational tools to control the process parameters, enable on-line measurements and acquisition with feedback to the optimized process parameters, and eventually track material evolution through each step of the additive process. Computational fluid dynamics is used for accurate prediction and calibration of the thermal field during WAAM process. and phase field models for microstructure evolution as a function of processing parameters to establish a connection between additive parameters and the final microstructure. Here we report cellular automata (CA) model development to predict the dendritic microstructure evolution with surface and bulk nuclei for single track and multiple layers. The CA model was developed to account for secondary element addition and predict segregation, local melting, and latent heat release as well as prediction of Euler angles from orientation information and validated against experiments. This framework was utilized to tailor spatially-varying composition in a part by appropriately controlling the microstructure evolution during the additive process. Functionally graded Haynes 282 alloy with high Cr content at the surface was tested for oxidation and mechanical properties. An advanced physics-based reaction-diffusion model predicting the simultaneous creation of chromium oxide and alumina is developed and validated to extend life expectancy of the WAAM manufactured high temperature part. A machine-learning data-driven framework establishing the process-structure relationship from a dataset of real microstructure images and corresponding process history data has been developed and implemented in the NX Siemens design system. The digital twin configuration along with the tool path generation enabled prediction of WAAM component buildup time and the techno-economic analysis provided a favorable option for all 4 cases with 15-40% cost reduction.
33 ADVANCED PROPULSION SYSTEMS↗
Toward a Theory of the Evolution of Drop Morphology and Splintering by Freezing
Abstract The drop freezing process is described by a phase-field model. Two cases are considered: when the freezing is triggered by central nucleation and when nucleation occurs on the drop surface. Depending on the environmental temperature and drop size, different morphological structures develop. Detailed dendritic growth was simulated at the first stage of drop freezing. Independent of the nucleation location, a decrease in temperature within the range from ~−5° to −25°C led to an increase in the number of dendrites and a decrease in their width and the interdendritic space. At temperatures lower than about −25°C, a planar front developed following surface nucleation, while dendrites formed a granular-like structure with small interdendritic distances following bulk nucleation. An ice shell grew in at the same time (but slower) as dendrites following surface nucleation, while it started forming once the dendrites have reached the drop surface in the case of central nucleation. The formed ice morphology at the first freezing stage predefined the splintering probability. We assume that stresses needed to break the ice shell arose from freezing of the water in the interdendritic spaces. Under this assumption, the number of possible splinters/fragments was proportional to the number of dendrites, and the maximum rate of splintering/fragmentation occurred within a temperature range of about −10° to −20°C, is in agreement with available laboratory and in situ measurements. At temperatures < −25°C, freezing did not lead to the formation of significant stresses, making splintering unlikely. The number of dendrites increased with drop size, causing a corresponding increase in the number of splinters. Examples of morphology that favors drop cracking are presented, and the duration of the freezing stages is evaluated. Sensitivity of the freezing process to the surface fluxes is discussed.
54 ENVIRONMENTAL SCIENCES↗
Computational Tools for Additive Manufacture of Tailored Microstructure and Properties
Additive manufacturing has the potential to revolutionize industrial hardware and unlock efficiency gains through the fabrication of geometries and architectures not possible by conventional processing. Currently most additive builds use a single set of process parameters (e.g. laser power and scan speed) which results in a part with a homogenous microstructure that provides a singular performance level. To move beyond this state, Raytheon Technologies Research Center worked to create a set of computational tools to track material evolution through each step of the additive process. Computational fluid dynamics and phase field models for microstructure evolution as a function of processing parameters, and crystal plasticity models fully coupling microstructure and mechanical properties for performance predictions were leveraged to establish a connection between additive parameters and the final microstructure. This framework was utilized to tailor spatially-varying mechanical properties in a part by appropriately controlling the microstructure evolution during the additive process. Specifically, a turbine blade was 3D printed from nickel superalloy IN718 using laser powder bed fusion with coarse grains in the airfoil section which experiences the highest temperatures and is creep limited while finer grains were printed in the root of the blade which experience higher stresses but at lower temperatures and is therefore fatigue limited. The benefit of being able to intentionally insert coarse grains in the high temperature region of the blade was showcased with a microstructure sensitive creep model that indicates longer creep life for coarser grains.
20 FOSSIL-FUELED POWER PLANTS↗
Precipitate growth kinetics under inhomogeneous concentration fields using a phase-field model
We investigate precipitation dynamics in the presence of a local solute gradient using phase-field simulations. During the homogenization heat treatment of the solidified Inconel 718 alloy, high Nb concentration within the Laves phases or at the core of the secondary arms results in Nb diffusion into the γ matrix. The volume fraction and spatial distribution of precipitation during subsequent annealing can be controlled by tailoring the Nb concentration gradient in the matrix during homogenization. We use a surrogate Ni-Fe-Nb alloy for Inconel 718 to explore the growth dynamics of δ precipitates related to the local Nb concentration levels. The simulations indicate that in the presence of a Nb concentration gradient the growth rate of δ precipitates is higher than in a matrix of uniform average Nb concentration. The higher growth rate is a result of the higher local thermodynamic driving force at the interface between the solute-rich matrix and the δ interface. Here, we propose a phenomenological model to describe the diffusion-controlled growth kinetics of the δ phase under a solute concentration gradient.
36 MATERIALS SCIENCE↗