Search NASA⌕ Search

Engineering topics

Adams, Mary S.

Publications and source records attributed to Adams, Mary S..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Automatic procedures for computing complete configuration geometry from individual component descriptions

Procedures are derived for developing a complete airplane surface geometry starting from component descriptions. The procedures involve locating the intersection lines of adjacent components and omitting any regions for which part of one surface lies within the other. The geometry files utilize the wave-drag (Harris) format, and output files are written in Hess format. Two algorithms are used: one, if both intersecting surfaces have airfoil cross sections; the other, if one of the surfaces has circular cross sections. Some sample results in graphical form are included.

Barger, Raymond L.↗
NASA NTRS1994

Automatic computation of Euler-marching and subsonic grids for wing-fuselage configurations

Algebraic procedures are described for the automatic generation of structured, single-block flow computation grids for relatively simple configurations (wing, fuselage, and fin). For supersonic flows, a quasi two-dimensional grid for Euler-marching codes is developed, and some sample results in graphical form are included. A type of grid for subsonic flow calculation is also described. The techniques are algebraic and are based on a generalization of the method of transfinite interpolation.

Barger, Raymond L.↗
NASA NTRS1993

Automatic computation of wing-fuselage intersection lines and fillet inserts with fixed-area constraint

Procedures for automatic computation of wing-fuselage juncture geometry are described. These procedures begin with a geometry in wave-drag format. First, an intersection line is computed by extrapolating the wing to the fuselage. Then two types of filleting procedures are described, both of which utilize a combination of analytical and numerical techniques appropriate for automatic calculation. An analytical technique for estimating the added volume due to the fillet is derived, and an iterative procedure for revising the fuselage to compensate for this additional volume is given. Sample results are included in graphical form.

Barger, Raymond L.↗
NASA NTRS1992

Design and analysis of low boom concepts at Langley Research Center

The objective of the sonic boom research in the current High Speed Research Program is to ultimately make possible overland supersonic flight by a high speed civil transport. To accomplish this objective, it is felt that results in four areas must demonstrate that such a vehicle would be acceptable by the general public, by the airframers, and by the airlines. It should be demonstrated: (1) that some waveform shape has the possibility of being acceptable to the general public; (2) that the atmosphere would not totally destroy such a waveform during propagation; (3) that a viable airplane could be built which produces such a waveform; and (4) that any performance penalty suffered by a low boom aircraft would be counteracted by the economic benefit of overland supersonic flight. The work being done at LaRC is in support of the third element listed above--the area of configuration design. The initial part of the paper will give a review of the theory being used for configuration designs and discuss two theory validation models which were built and tested within the past two years. Discussion of the wind tunnel and theoretical results (linear theory and higher order methods) and their implications for future designs will be included.

Darden, Christine M.↗
NASA NTRS1990

Fuselage design for a specified Mach-sliced area distribution

A procedure for designing a fuselage having a prescribed effective area distribution computed from -90 deg Mach slices is described. This type of calculation is an essential tool in designing a complete configuration with an effective area distribution that corresponds to a desired sonic boom signature shape. Sample calculations are given for M=2 and M=3 designs. The examples include fuselages constrained to have circular cross sections and fuselages having cross sections of arbitrary shape. It is found that, for a prescribed effective area distribution having sharp variations, the iterative procedure converges to a smoothed approximation to the prescribed distribution. For a smooth prescribed area distribution, the solution is not unique.

Barger, Raymond L.↗
NASA NTRS1989

Mixing enhancement in a supersonic combustor

Research has been conducted for a number of years at the NASA Langley Research Center to develop a supersonic combustion ramjet (scramjet) capable of propelling a vehicle at hypersonic speeds in the atmosphere or beyond. Recently, that research has been directed toward the optimization of the scramjet combustor, and in particular the efficiency of fuel-air mixing and reaction in the engine. This paper describes a numerical study of fuel-air mixing and reaction in a supersonic combustor, and discusses the analysis of a technique that was used to enhance the mixing processes and overall combustion efficiency in the flow. Based on the results of that study, conclusions are drawn regarding the applicability of the technique to enhance mixing in a scramjet combustor.

Drummond, J. Philip↗