Search NASA⌕ Search

Engineering topics

Addessio, Francis L.

Publications and source records attributed to Addessio, Francis L..

Modeling Microstructural Effects on Heterogeneous Temperature Fields within Polycrystalline Explosives

The paper addresses the role of crystal anisotropy on the evolution of heterogeneous temperature fields in plastic-bonded explosives (PBXs) under conditions of weak shock. The modeling approach is based on simplified idealizations of PBX microstructure including RDX grains and estane binder regions subjected to velocity boundary conditions representative of impact conditions in situ. The constitutive description of the microstructure constituents includes a dislocation-based, anisotropic, single crystal plasticity model for the explosive grains and a linear viscoelastic model to represent the estane binder. Large suites of simulations were used to systematically study the correlation in heating of the grains with local wave dynamics, crystal orientation, and the microstructural neighborhood. These correlations were identified through the selection of characteristics of crystal anisotropy including oriented wave speeds and Taylor factor. A key observation is that the wave dispersion within a certain distance from the impact interface plays a dominant role in the temperature field. Beyond this distance, individual crystal orientations play a more dominant role, but cannot entirely account for the observed heterogeneity without consideration of the local microstructure neighborhood.

42 ENGINEERING↗

Single Crystal Plasticity Model with Deformation Twinning for the High Rate Deformation of β-HMX

Deformation twinning is an active deformation mechanism during loading along certain crystallographic directions of β-cyclotetramethylene tetranitramine (β-HMX). In this work, a finite strain thermomechanical model is extended to include twinning as a deformation mechanism in addition to plastic slip. The stress is derived from the free energy expression including a term representing the equation of state. The crystal plasticity framework is used to divide the total strain into inelastic and elastic component, where the elastic part is used in the expression for the free energy. The twin systems are treated as pseudo slip systems and the shear rate on the twin systems is evaluated in terms of the twin resistance and the projection of the stress tensor. The model parameters were calibrated against a set of plate impact experiments performed on β-HMX by Dick et al. The remaining plate impact experiments are used to evaluate the predictive capability of the model. The quality of the model fits and predictions is discussed from a physical and modeling perspective. Particularly, the role of twin modeling on results is highlighted. Finally, the model is used to explore the relationship between the propensity for twinning and crystal orientation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Path dependency of phase transformations

At high pressures titanium and zirconium are known to undergo a phase transformation from the hexagonal close packed (HCP), alpha-phase to the simple-hexagonal, omega-phase. Under conditions of shock loading, the high-pressure omega-phase can be retained upon release. It has been shown that temperature, peak shock stress, and texture can influence the transformation. Moreover, under these same loading conditions, plastic processes of slip and twinning are also affected by similar differences in the loading path. To understand this path dependency and it role on microstructural evolution, in-situ velocimetry measurements along with post-mortem metallographic and neutron diffraction characterization of soft recovered specimens have been utilized to qualitatively understand the kinetics of transformation, quantify volume fraction of retained omega-phase and characterize the shocked alpha and omega-phases. Together the work described here can be utilized to understand phase and structure for these metals and lend insight into the partitioning of plastic processes between phases far from equilibrium conditions. Experiments discussed here, reveal that the transformation from alpha to omega phase is more difficult in Ti than in Zr metals. This result is discussed in terms of both differences in shear modulus and free space within the lattice for these systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Shock and Microstructural Characterization of the α-ω Phase Transition in Titanium Crystals

In this paper, a multicrystal comprised of a small number of large crystals of high-purity titanium and a [ 0001 ] oriented high-purity single crystal titanium sample were shock loaded using gas gun plate impact experiments. Tests were performed at stresses above the &#x03B1;<!-- α --> &#x2212;<!-- - --> &#x03C9;<!-- ω --> phase transition stress (for high-purity polycrystalline specimens) to observe the behavior of oriented crystals under similar conditions. Post-mortem characterization of the shocked microstructure was conducted on the single crystal sample to measure textures, and quantify phases and twinning. The apparent activation of plastic and transformation mechanisms was dependent upon crystal orientation. Specifically, the [ 0001 ] crystal showed a higher Hugoniot elastic limit than the [ 10 1 &#x00AF;<!-- ¯ --> 0 ] or [ 3 1 &#x00AF;<!-- ¯ --> 4 &#x00AF;<!-- ¯ --> 4 ] orientations. The slope of velocity as a function of time was lower in the [ 0001 ] orientation than the other orientations during plastic deformation, indicating sluggish transformation kinetics for the α to ω phase transition for the [ 0001 ] oriented crystal. Finally, microtexture measurements of a recovered [ 0001 ] oriented single crystal revealed the presence of retained ω phase after unloading, with orientations of the constituent phase fractions indicative of the forward α→ω transition, rather than the reverse ω→α transition, suggesting that the material never achieved a state of 100% ω phase.

36 MATERIALS SCIENCE↗

A High-Rate, Single-Crystal Model for Cyclotrimethylene Trinitramine including Phase Transformations and Plastic Slip

A continuum model for the high-rate, thermo-mechanical deformation of single-crystal cyclotrimethylene trinitramine (RDX) is developed. The model includes the effects of anisotropy, large deformations, nonlinear thermo-elasticity, phase transformations, and plastic slip. A multiplicative decomposition of the deformation gradient is used. The volumetric elastic component of the deformation is accounted for through a free-energy based equation of state for the low- (α) and high-pressure (γ) polymorphs of RDX. Crystal plasticity is addressed using a phenomenological thermal activation model. The deformation gradient for the phase transformation is based on an approach that has been applied to martensitic transformations. Simulations were conducted and compared to high-rate, impact loading of oriented RDX single crystals. The simulations considered multiple orientations of the crystal relative to the direction of shock loading and multiple sample thicknesses. Thirteen slip systems, which were inferred from indentation and x-ray topography, were used to model the α-polymorph. It is shown that by increasing the number of slip systems from the previously considered number of six (6) to thirteen (13) in the α-polymorph, better comparisons with data may be obtained. Simulations of impact conditions in the vicinity of the α- to γ-polymorph transformation (3.8 GPa) are considered. Eleven of the simulations, which were at pressures below the transformation value (3.0 GPa), were compared to experimental data. Comparison of the model was also made with available data for one experiment above the transformation pressure (4.4 GPa). Also, simulations are provided for a nominal pressure of 7.5 GPa to demonstrate the effect of the transformation kinetics on the deformation of a high-rate plate impact problem.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

A dislocation density-based continuum model of the anisotropic shock response of single crystal α-cyclotrimethylene trinitramine

Here, we have developed a model for the finite deformation thermomechanical response of α-cyclotrimethylene trinitramine (RDX). Our model accounts for nonlinear thermoelastic lattice deformation through a free energy-based equation of state developed by Cawkwell et al. (2016) in combination with temperature and pressure dependent elastic constants, as well as dislocation-mediated plastic slip on a set of slip systems motivated by experimental observation. The kinetics of crystal plasticity are modeled using the Orowan equation relating slip rate to dislocation density and the dislocation velocity developed by Austin and McDowell (2011), which naturally accounts for transition from thermally activated to dislocation drag limited regimes. Evolution of dislocation density is specified in terms of local ordinary differential equations reflecting dislocation–dislocation interactions. This paper presents details of the theory and parameterization of the model, followed by discussion of simulations of flyer plate impact experiments. Impact conditions explored within this combined simulation and experimental effort span shock pressures ranging from 1 to 3 GPa for four crystallographic orientations and multiple specimen thicknesses. Simulation results generated using this model are shown to be in strong agreement with velocimetry measurements from the corresponding plate impact experiments. Finally, simulation results are used to motivate conclusions about the nature of dislocation-mediated plasticity in RDX.

36 MATERIALS SCIENCE↗

A High-Rate, Single-Crystal Model including Phase Transformations, Plastic Slip, and Twinning

An anisotropic, rate-­dependent, single-­crystal approach for modeling materials under the conditions of high strain rates and pressures is provided. The model includes the effects of large deformations, nonlinear elasticity, phase transformations, and plastic slip and twinning. It is envisioned that the model may be used to examine these coupled effects on the local deformation of materials that are subjected to ballistic impact or explosive loading. The model is formulated using a multiplicative decomposition of the deformation gradient. A plate impact experiment on a multi-­crystal sample of titanium was conducted. The particle velocities at the back surface of three crystal orientations relative to the direction of impact were measured. Molecular dynamics simulations were conducted to investigate the details of the high-­rate deformation and pursue issues related to the phase transformation for titanium. Simulations using the single crystal model were conducted and compared to the high-­rate experimental data for the impact loaded single crystals. The model was found to capture the features of the experiments.

36 MATERIALS SCIENCE↗

A thermodynamically consistent discontinuous Galerkin formulation for interface separation

Our paper describes the formulation of an interface damage model, based on the discontinuous Galerkin (DG) method, for the simulation of failure and crack propagation in laminated structures. The DG formulation avoids common difficulties associated with cohesive elements. Specifically, it does not introduce any artificial interfacial compliance and, in explicit dynamic analysis, it leads to a stable time increment size which is unaffected by the presence of stiff massless interfaces. This proposed method is implemented in a finite element setting. Convergence and accuracy are demonstrated in Mode I and mixed-mode delamination in both static and dynamic analyses. Significantly, numerical results obtained using the proposed interface model are found to be independent of the value of the penalty factor that characterizes the DG formulation. By contrast, numerical results obtained using a classical cohesive method are found to be dependent on the cohesive penalty stiffnesses. The proposed approach is shown to yield more accurate predictions pertaining to crack propagation under mixed-mode fracture because of the advantage. Furthermore, in explicit dynamic analysis, the stable time increment size calculated with the proposed method is found to be an order of magnitude larger than the maximum allowable value for classical cohesive elements.

42 ENGINEERING↗

Characterization of Depleted-Uranium Strength and Damage Behavior

The intent of this report is to document the status of our knowledge of the mechanical and damage behavior of Depleted Uranium(DU hereafter). This report briefly summaries the motivation of the experimental and modeling research conducted at Los Alamos National Laboratory(LANL) on DU since the early 1980’s and thereafter the current experimental data quantifying the strength and damage behavior of DU as a function of a number of experimental variables including processing, strain rate, temperature, stress state, and shock prestraining. The effect of shock prestraining on the structure-property response of DU is described and the effect on post-shock mechanical behavior of DU is discussed. The constitutive experimental data utilized to support the derivation of two constitutive strength (plasticity) models, the Preston-Tonks-Wallace (PTW) and Mechanical Threshold Stress (MTS) models, for both annealed and shock prestrained DU are detailed and the Taylor cylinder validation tests and finite-element modeling (FEM) utilized to validate these strength models is discussed. The similarities and differences in the PTW and MTS model descriptions for DU are discussed for both the annealed and shock prestrained conditions. Quasi-static tensile data as a function of triaxial constraint and spallation test data are described. An appendix additionally briefly describes low-pressure equation-of-state data for DU utilized to support the spallation experiments. The constitutive behavior of DU screw/bolt material is presented. The response of DU subjected to dynamic tensile extrusion testing as a function of temperature is also described. This integrated experimental technique is planned to provide an additional validation test in the future. The damage data as a function of triaxiality, tensile and spallation data, is thereafter utilized to support derivation of the Tensile Plasticity (TEPLA) damage model and simulations for comparison to the DU spallation data are presented. Finally, a discussion of future needs in the area of needed DU strength and damage research at LANL is presented to support the development of physically-based predictive strength and damage modeling capability.

36 MATERIALS SCIENCE↗