Search NASA⌕ Search

Engineering topics

Ade, B. J.

Publications and source records attributed to Ade, B. J..

Transformational challenge reactor design characteristics

The Transformational Challenge Reactor (TCR) program was conceived with the goal to reduce costs and time frames associated with advanced reactor deployment by leveraging developments in advanced manufacturing, advanced materials, data science, and rapid prototyping and testing. The final deliverable of the TCR program was to be an operational test of a novel reactor design. The TCR core design incorporates a dense tri-structural-isotropic/SiC fuel form and volumetrically efficient yttrium hydride moderator, both of which were manufactured and characterized under the TCR program. The TCR is a 3 MW{sub th} He-cooled experimental nuclear reactor designed to reach a total integrated burnup of less than 24 effective full-power hours to keep the radioactive source term to a very low level. TCR design process revealed a positive moderator coefficient; however, the negative doppler coefficients for the fuel and thermal expansion of fuel, moderator, and core support plate yield an overall negative reactivity coefficient. Calculated fuel element temperatures and stresses are well within safety margins. The maximum hypothetical accident (i.e., de-pressurized loss of forced cooling) yields only a modest increase in reactor temperatures that are all within safety margins. This paper summarizes the high-level TCR design characteristics, which were derived from neutronics, thermohydraulics, thermomechanics, and safety analyses.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Transformational Challenge Reactor preconceptual core design studies

In the nuclear industry, a manufacturing-informed design approach has the potential to yield the most benefit from advanced manufacturing. By leveraging advanced materials, data science, and rapid testing and deployment, manufacturing-informed design can drive down costs and development times, ultimately improving future commercial viability. This approach is being demonstrated in the US Department of Energy Office of Nuclear Energy (DOE-NE) Transformational Challenge Reactor (TCR) program. Preconceptual design activities for TCR have been focused on analyzing and maturing four reactor core design concepts: two fast-spectrum and two thermal-spectrum systems. Furthermore, the designs were iteratively modified and analyzed, and subcomponents were manufactured in parallel over weeks instead of months or years. To meet key program initiatives (e.g., timeline and material use), several constraints—including fissile material availability, component availability, materials compatibility, and additive manufacturing capabilities—were factored into the design effort, yielding small cores less than one cubic meter in volume with near-term viability. Additionally, the TCR program has made significant progress on development of advanced moderator materials such as yttrium hydride, advancing the feasibility of gas-cooled thermal spectrum systems using less than 250 kg of high-assay low enriched uranium (HALEU) and occupying less than 1 m3. Each of the two resulting thermal designs uses a different fuel form: traditional UO2 ceramic fuel and tristructural isotropic (advanced TRISO) fuel particles embedded inside a SiC matrix. Core neutronics and thermal performance for these systems were assessed and summarized. Evaluation of the performance metrics for these two moderated designs has yielded the downselected TCR design: a TRISO-fueled and yttrium hydride moderated gas-cooled reactor.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Impact of assembly-specific conditions on BWR burnup credit

Because boiling water reactors use control blades during operation, there can be significant changes to the local axial power shape, coolant density profile, and other parameters when the blades are inserted. Previous work examined the reactor operating parameters that impact cask reactivity. These previous studies identified limiting conditions for fuel cask reactivity or the direction of trends with cask reactivity (e.g., lower coolant densities result in higher cask reactivity). However, using limiting conditions for all parameters simultaneously is unrealistic. When the control blades are inserted deeply into the reactor - a limiting condition - the power is reduced and the void fraction decreases - a less limiting condition. This paper identifies the impacts of using assembly-specific conditions for control blade history, coolant density profile, burnup profile, and fuel temperature profile. Results indicate that cask reactivity is reduced when using assembly-specific operating conditions versus combining limiting conditions for the individual parameters of interest. The magnitude of reactivity reduction for using assembly- specific conditions varies based on each assembly and its operating conditions. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Apparent Monte Carlo Source Convergence Problem with BWR Fuel Depleted with Partial Control Blade Insertion

Oak Ridge National Laboratory (ORNL) and the US Nuclear Regulatory Commission (NRC) have initiated a multiyear project to investigate application of burnup credit (BUC) to boiling-water reactor (BWR) fuel in storage and transportation casks and spent fuel pools (SFPs). Ideally, a single combination of all operating parameters including moderator density and axial burnup profiles, control blade exposure, and others can be identified to allow a simple, bounding approach to BWR BUC. One aspect of this investigation involves examining the effect of control blade insertion during operation on discharged assembly reactivity. In the course of these calculations, an apparent source convergence problem was discovered for fuel that has experienced partial blade insertion for the entire lifetime of the assembly. The source convergence problem appears not to impact k{sub eff}, but it manifests in predictions of the axial fission density profile. This phenomenon is of interest in identifying areas of concern with BWR BUC since it has not been studied as thoroughly as BUC for pressurized-water (PWR) reactor fuel. There may also be interest in this configuration for further study of a realistic source Monte Carlo convergence problem as opposed to some earlier manufactured source convergence problems through careful selection of initial conditions. This summary presents the depletion conditions used to generate the problem, a description of the models, a background based on well-behaved calculations, the identification of the problem, and attempts made to resolve the problem. Only a brief description of the depletion conditions and models is possible within the limited scope of this summary. Finally, conclusions are presented. This summary identifies a source convergence problem in the process of investigating BUC for BWR spent fuel. The depletion scenario which created the depleted fuel and burnable absorber compositions included a control blade inserted in the bottom 14 nodes throughout the entire depletion. This insertion is slightly over half the length of the assembly, and it appears to create two regions of nearly equal reactivity. As expected, one region is near the top of the assembly, and the other region is near the middle of the assembly. This node includes significant {sup 239}Pu generation as a result of rodded operation, but it is also the top node of the full lattice zone. While the calculated k{sub eff} values appear to be statistically equivalent, the axial neutron production profile varies significantly among independent simulations of the same model. A range of standard approaches has been used to attempt to resolve the source convergence problem and determine the true axial neutron production profile. This profile is of interest in cask criticality safety analysis because it influences the interaction among assemblies loaded in the cask. The forthcoming SCALE 6.2 release will include source convergence testing based on Shannon entropy, which may assist in identifying these types of problems in the future. It should be noted that this source convergence problem results from the depletion conditions and the final distribution of fissile and absorber material within the discharged fuel assembly. The results, while entirely generated within the SCALE code system, are representative of any Monte Carlo program attempting to calculate k{sub eff} for such a system. The most important conclusion of this work is that the BUC criticality safety community must be aware of the potential for this type of source convergence problem. Analysts must approach such partially rodded scenarios with caution and critically examine the results. Fortunately, it is extremely unlikely that BWR assemblies would experience the bladed operation necessary to create this particular source convergence problem. These results may also have some bearing on the analysis of PWR BUC for new plant designs such as AP1000 that incorporate significant rodded operations. In a broader context, the source convergence problem identified here could have been magnified if it had occurred in a Monte Carlo depletion simulation. It may be possible to identify this type of problem in a depletion calculation by comparing the apparently converged fluxes between steps to ensure that no oscillations or other serious shifts are occurring. The depletion calculations performed in this work were performed with a two-dimensional deterministic code and are therefore not subject to this problem. These results may also raise questions about the validity of 2D depletion models with extruded geometry in the 3D k{sub eff} calculation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Impact of modeling choices on inventory and in-cask criticality calculations for FORSMARK 3 BWR spent fuel - 14441

Simulation of boiling water reactor (BWR) fuel depletion poses a challenge for nuclide inventory validation and nuclear criticality safety analyses. This challenge is due to the complex operating conditions and assembly design heterogeneities that characterize these nuclear systems. Fuel depletion simulations and in-cask criticality calculations are affected by (1) completeness of design information, (2) variability of operating conditions needed for modeling purposes, and (3) possible modeling choices. These effects must be identified, quantified, and ranked according to their significance. This paper presents an investigation of BWR fuel depletion using a complete set of actual design specifications and detailed operational data available for five operating cycles of the Swedish BWR Forsmark 3 reactor. The data includes detailed axial profiles of power, burnup, and void fraction in a very fine temporal mesh for a GE14 (10x10) fuel assembly. The specifications of this case can be used to assess the impacts of different modeling choices on inventory prediction and in-cask criticality, specifically regarding the key parameters that drive inventory and reactivity throughout fuel burnup. This study focused on the effects of the fidelity with which power history and void fraction distributions are modeled. The corresponding sensitivity of the reactivity in storage configurations is assessed, and the impacts of modeling choices on decay heat and inventory are addressed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Coolant density and control blade history effects in extended BWR burnup credit - 14494

Oak Ridge National Laboratory and the US Nuclear Regulatory Commission have initiated a multiyear project to investigate the application of burnup credit (BUC) for boiling water reactor (BWR) fuel in storage and transportation casks. This project includes two phases. The first phase investigates the applicability of peak reactivity methods currently used for spent fuel pools to spent fuel storage and transportation casks and the validation of reactivity (k{sub eff}) calculations and predicted spent fuel compositions. The second phase focuses on extending BUC beyond peak reactivity. This paper documents work performed to date investigating some aspects of extended BUC. The technical basis for application of peak reactivity methods to BWR fuel in storage and transportation systems is presented in a companion paper. Two reactor operating parameters are being evaluated to establish an adequate basis for extended BWR BUC: (1) the effect of axial void profile and (2) the effect of control blade utilization during operation. A detailed analysis of core simulator data for one cycle of a modern operating BWR plant was performed to determine the range of void profiles and the variability of the profile experienced during irradiation. Although a single cycle does not provide complete data, the data obtained are sufficient to determine the primary effects and to identify conservative modeling approaches. These data were used in a study of the effect of axial void profile. The first stage of the study was determination of the necessary moderator density temporal fidelity in depletion modeling. After the required temporal fidelity was established, multiple void profiles were used to examine the effect on cask reactivity. The results of these studies are being used to develop recommendations for conservatively modeling the void profile effects for BWR depletion calculations. The second operational parameter studied was control blade history. Control blades are inserted in various locations and at varying degrees during BWR operation based on the core loading pattern. When present during depletion, control blades harden the neutron spectrum locally because they displace the moderator and absorb thermal neutrons. The investigation of the effect of control blades on post operational cask reactivity is documented herein, as is the effect of multiple (continuous and intermittent) exposure periods with control blades inserted. The coupled effects of control blade presence on power density, void profile, or burnup profile will be addressed in future work. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Technical basis for peak reactivity burnup credit for BWR spent nuclear fuel in storage and transportation systems - 14601

Oak Ridge National Laboratory and the United States Nuclear Regulatory Commission have initiated a multiyear project to investigate application of burnup credit for boiling-water reactor (BWR) fuel in storage and transportation casks. This project includes two phases. The first phase (1) investigates applicability of peak reactivity methods currently used in spent fuel pools (SFPs) to storage and transportation systems and (2) evaluates validation of both reactivity (k{sub eff}) calculations and burnup credit nuclide concentrations within these methods. The second phase will focus on extending burnup credit beyond peak reactivity. This paper documents the first phase, including an analysis of lattice design parameters and depletion effects, as well as both validation components. Initial efforts related to extended burnup credit are discussed in a companion paper. Peak reactivity analyses have been used in criticality analyses for licensing of BWR fuel in SFPs over the last 20 years. These analyses typically combine credit for the gadolinium burnable absorber present in the fuel with a modest amount of burnup credit. Gadolinium burnable absorbers are used in BWR assemblies to control core reactivity. The burnable absorber significantly reduces assembly reactivity at beginning of life, potentially leading to significant increases in assembly reactivity for burnups less than 15-20 GWd/MTU. The reactivity of each fuel lattice is dependent on gadolinium loading. The number of gadolinium-bearing fuel pins lowers initial lattice reactivity, but it has a small impact on the burnup and reactivity of the peak. The gadolinium concentration in each pin has a small impact on initial lattice reactivity but a significant effect on the reactivity of the peak and the burnup at which the peak occurs. The importance of the lattice parameters and depletion conditions are primarily determined by their impact on the gadolinium depletion. Criticality code validation for BWR burnup credit at peak reactivity requires a different set of experiments than for pressurized-water reactor burnup credit analysis because of differences in actinide compositions, presence of residual gadolinium absorber, and lower fission product concentrations. A survey of available critical experiments is presented along with a sample criticality code validation and determination of undercoverage penalties for some nuclides. The validation of depleted fuel compositions at peak reactivity presents many challenges which largely result from a lack of radiochemical assay data applicable to BWR fuel in this burnup range. In addition, none of the existing low burnup measurement data include residual gadolinium measurements. An example bias and uncertainty associated with validation of actinide-only fuel compositions is presented. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗