Engineering topics
Ade, Harald
Publications and source records attributed to Ade, Harald.
Revealing aggregation of non-fullerene acceptors in intermixed phase by ultraviolet-visible absorption spectroscopy
Non-fullerene acceptor (NFA) aggregation is crucial in determining bulk-heterojunction (BHJ) organic photovoltaic (OPV) performance. However, it is still a big challenge to characterize the nanostructure of NFAs in the disordered donor-acceptor intermixed phase. Here, we demonstrate a method to characterize NFA aggregation and composition in the intermixed phase by measuring NFA concentration-dependent ultraviolet-visible (UV-vis) absorption spectroscopy of BHJ films. In various polymer:NFA films, an absorption shift as a function of increasing molecular concentration (ASIMC) phenomenon is observed, and different NFA aggregation behaviors can be distinguished. The ASIMC method was then applied to study the influence of processing conditions on the NFA concentration in the intermixed phase of devices to establish a correlation with device efficiency. The current work provides a feasible tool to study the nanostructure of NFAs in the complex polymer matrix and to understand the variations in the NFA concentration in the intermixed phase under non-equilibrium conditions.
A Top-Down Strategy to Engineer ActiveLayer Morphology for Highly Efficient and Stable All-Polymer Solar Cells
A major challenge hindering the further development of all-polymer solar cells (all-PSCs) employing polymerized small-molecule acceptors is the relatively low fill factor (FF) due to the difficulty in controlling the active-layer morphology. The issues typically arise from oversized phase separation resulting from the thermodynamically unfavorable mixing between two macromolecular species, and disordered molecular orientation/packing of highly anisotropic polymer chains. Herein, a facile top-down controlling strategy to engineer the morphology of all-polymer blends is developed by leveraging the layer-by-layer (LBL) deposition. Optimal intermixing of polymer components can be achieved in the two-step process by tuning the bottom-layer polymer swelling during top-layer deposition. Consequently, both the molecular orientation/packing of the bottom layer and the molecular ordering of the top layer can be optimized with a suitable top-layer processing solvent. A favorable morphology with gradient vertical composition distribution for efficient charge transport and extraction is therefore realized, affording a high all-PSC efficiency of 17.0% with a FF of 76.1%. The derived devices also possess excellent long-term thermal stability and can retain >90% of their initial efficiencies after being annealed at 65 °C for 1300 h. In conclusion, these results validate the distinct advantages of employing an LBL processing protocol to fabricate high-performance all-PSCs.
Optimizing spectral and morphological match of nonfullerene acceptors toward efficient indoor organic photovoltaics with enhanced light source adaptability
High-performance indoor organic photovoltaics (IOPV) require large-bandgap material systems to absorb visible light efficiently and reduce energy loss. However, state-of-the-art non-fullerene acceptors (NFAs) have absorptions in the near-infrared region and are thus not suitable for IOPV applications. Herein, we report a series of large-bandgap (>1.70 eV) NFAs named FCC-Cl-C8, FCC-Cl-4Ph and FCC-Cl-6Ph by modifying the alkyl side chains with alkylphenyl chains partially or completely. Results show that the bulky alkylphenyl side chains can finely tune the absorption properties of the NFAs and also affect their morphological properties. Interestingly, the best-performing NFA is the one (named FCC-Cl-4Ph) with partial alkyl and alkylphenyl substitutions, which blue-shift the absorption of the NFAs while minimizing the negative morphological effect of the bulky alkylphenyl chains. As a result, FCC-Cl-4Ph can achieve excellent indoor efficiencies over 29% under a 3000 K LED lamp at 1000 lux and show better solution processability over FCC-Cl-C8. More importantly, FCC-Cl-4Ph can maintain high indoor performance (29.7–26.8% at 1000 lux) under a wide range of indoor lighting spectra (2600, 3000, 4000, and 6500 K LED lamps), which should be due to the blue-shifted spectra of FCC-Cl-4Ph and better matching with various indoor conditions. Finally, this work reveals an interesting structure-property relationship and offers useful strategies for the further design of NFAs toward efficient IOPV devices.
16.52% Efficiency All-Polymer Solar Cells with High Tolerance of the Photoactive Layer Thickness
All-polymer solar cells (all-PSCs) have drawn growing attention and achieved tremendous progress recently, but their power conversion efficiency (PCE) still lags behind small-molecule-acceptor (SMA)-based PSCs due to the relative difficulty on morphology control of polymer photoactive blends. Here, in this work, low-cost PTQ10 is introduced as a second polymer donor (a third component) into the PM6:PY-IT blend to finely tune the energy-level matching and microscopic morphology of the polymer blend photoactive layer. The addition of PTQ10 decreases the π–π stacking distance, and increases the π–π stacking coherence length and the ordered face-on molecular packing orientation, which improves the charge separation and transport in the photoactive layer. Moreover, the deeper highest occupied molecular orbital energy level of the PTQ10 polymer donor than PM6 leads to higher open-circuit voltage of the ternary all-PSCs. As a result, a PCE of 16.52% is achieved for ternary all-PSCs, which is one of the highest PCEs for all-PSCs. In addition, the ternary devices exhibit a high tolerance of the photoactive layer thickness with high PCEs of 15.27% and 13.91% at photoactive layer thickness of ≈205 and ≈306 nm, respectively, which are the highest PCEs so far for all-PSCs with a thick photoactive layer.
Ultrathin P(NDI2OD-T2) Films with High Electron Mobility in Both Bottom-Gate and Top-Gate Transistors
Not provided.
Solid additive tuning of polymer blend morphology enables non-halogenated-solvent all-polymer solar cells with an efficiency of over 17%
The treatment of toluene solvent and DTT additive enables the PBQ6:PYF-T- o -based all-PSC devices with PCE up to 17.06%, which is one of the highest value in non-halogenated-processed all-PSCs to date.
Understanding, quantifying, and controlling the molecular ordering of semiconducting polymers: from novices to experts and amorphous to perfect crystals
Molecular packing and texture of semiconducting polymers are often critical to the performance of devices using these materials. Although frameworks exist to quantify the ordering, interpretations are often just qualitative, resulting in imprecise use of terminology. Here, we reemphasize the significance of quantifying molecular ordering in terms of degree of crystallinity (volume fractions that are ordered) and quality of ordering and their relation to the size scale of an ordered region. We are motivated in part by our own imprecise and inconsistent use of terminology in the past, as well as the need to have a primer or tutorial reference to teach new group members. We strive to develop and use consistent terminology with regards to crystallinity, semicrystallinity, paracrystallinity, and related characteristics. To account for vastly different quality of ordering along different directions, we classify paracrystals into 2D and 3D paracrystals and use paracrystallite to describe the spatial extent of molecular ordering in 1–10 nm. We show that a deeper understanding of molecular ordering can be achieved by combining grazing-incidence wide-angle X-ray scattering and differential scanning calorimetry, even though not all aspects of these measurements are consistent, and some classification appears to be method dependent. We classify a broad range of representative polymers under common processing conditions into five categories based on the quantitative analysis of the paracrystalline disorder parameter (g) and thermal transitions. A small database is presented for 13 representative conjugated and insulating polymers ranging from amorphous to semi-paracrystalline. Lastly, we outline the challenges to rationally design more perfect polymer crystals and propose a new molecular design approach that envisions conceptual molecular grafting that is akin to strained and unstrained hetero-epitaxy in classic (compound) semiconductors thin film growth.
High Miscibility Compatible with Ordered Molecular Packing Enables an Excellent Efficiency of 16.2% in All-Small-Molecule Organic Solar Cells
In all-small-molecule organic solar cells (ASM-OSCs), a high short-circuit current (Jsc) usually needs a small phase separation, while a high fill factor (FF) is generally realized in a highly ordered packing system. However, small domain and ordered packing always conflicted each other in ASM-OSCs, leading to a mutually restricted J sc and FF. Here, in this study, alleviation of the previous dilemma by the strategy of obtaining simultaneous good miscibility and ordered packing through modulating homo- and heteromolecular interactions is proposed. By moving the alkyl-thiolation side chains from the para- to the meta-position in the small-molecule donor, the surface tension and molecular planarity are synchronously enhanced, resulting in compatible properties of good miscibility with acceptor BTP-eC9 and strong self-assembly ability. As a result, an optimized morphology with multi-length-scale domains and highly ordered packing is realized. The device exhibits a long carrier lifetime (39.8 μs) and fast charge collection (15.5 ns). A record efficiency of 16.2% with a high FF of 75.6% and a J sc of 25.4 mA cm –2 in the ASM-OSCs is obtained. These results demonstrate that the strategy of simultaneously obtaining good miscibility with high crystallinity could be an efficient photovoltaic material design principle for high-performance ASM-OSCs.
Introducing Low-Cost Pyrazine Unit into Terpolymer Enables High-Performance Polymer Solar Cells with Efficiency of 18.23%
Recently, a random ternary copolymerization strategy has become a promising and efficient approach to develop high-performance polymer donors for polymer solar cells (PSCs). Here, in this study, a low-cost electron-withdrawing unit, 2,5-bis(4-(2-ethylhexyl)thiophen-2-yl)pyrazine (PZ-T), is incorporated into the polymer backbone of PM6 as the third component, and three D-A 1 -D-A 2 type terpolymers PMZ-10, PMZ-20, and PMZ-30 are synthesized by the random copolymerization strategy, with the PZ-T proportion of 10%, 20%, and 30%, respectively. The terpolymers exhibit downshifted highest occupied molecular orbital energy levels than PM6, which is beneficial for obtaining higher open-circuit voltage (V oc ) of the PSCs with the polymer as a donor. Importantly, the PSCs based on PMZ-10:Y6 demonstrate efficient exciton dissociation, higher and balanced electron/hole mobilities, desirable aggregation, and high power conversion efficiency of 18.23%, which is the highest efficiency among the terpolymer-based PSCs so far. The results indicate that the ternary copolymerization strategy with PZ-T as the second A-unit is an efficient approach to further improve the photovoltaic performance and reduce the synthetic cost of the D-A copolymer donors.
Baseplate Temperature–Dependent Vertical Composition Gradient in Pseudo–Bilayer Films for Printing Non–Fullerene Organic Solar Cells
Numerous previous reports on the sequential deposition (SD) technique have demonstrated that this approach can achieve a p–i–n active layer architecture with an ideal vertical composition gradient, which is one of the critical factors that can influence the physical processes that determine the photovoltaic performance of organic solar cells. Herein, a commonly used photovoltaic system comprised of PM6 as a donor and Y6 as an acceptor is investigated with respect to sequential blade–processing deposition to comprehensively explore the morphology characteristics as a function of baseplate temperature. A systematic study of the temperature–dependent blend morphology elucidates the SD–processed configuration merits and device physics behind temperature–controlled degree of vertical composition gradient, and constructs the temperature–microstructure–property relationship for the corresponding photovoltaic parameters. The result shows, as the temperature increases, the morphology of the active layer has undergone a distinct evolution from the pseudo–bulk heterojunction to a pseudo–planar heterojunction and then to a pseudo–planar bilayer, leading to a non–monotonic correlation between baseplate temperature and device performance. Further, this investigation not only reveals the importance of precisely controlling baseplate temperature for gaining vertical morphology control, but also provides a path toward rational optimization of device performance in the lab–to–fab transition.
Polymerized small molecular acceptor based all-polymer solar cells with an efficiency of 16.16% via tuning polymer blend morphology by molecular design
All-polymer solar cells (all-PSCs) based on polymerized small molecular acceptors (PSMAs) have made significant progress recently. Here, we synthesize two A-DA’D-A small molecule acceptor based PSMAs of PS-Se with benzo[c][1,2,5]thiadiazole A’-core and PN-Se with benzotriazole A’-core, for the studies of the effect of molecular structure on the photovoltaic performance of the PSMAs. The two PSMAs possess broad absorption with PN-Se showing more red-shifted absorption than PS-Se and suitable electronic energy levels for the application as polymer acceptors in the all-PSCs with PBDB-T as polymer donor. Cryogenic transmission electron microscopy visualizes the aggregation behavior of the PBDB-T donor and the PSMA in their solutions. In addition, a bicontinuous-interpenetrating network in the PBDB-T:PN-Se blend film with aggregation size of 10~20 nm is clearly observed by the photoinduced force microscopy. The desirable morphology of the PBDB-T:PN-Se active layer leads its all-PSC showing higher power conversion efficiency of 16.16%.
A Chlorinated Donor Polymer Achieving High‐Performance Organic Solar Cells with a Wide Range of Polymer Molecular Weight
Abstract In the field of non‐fullerene organic solar cells (OSCs), compared to the rapid development of non‐fullerene acceptors, the progress of high‐performance donor polymers is relatively slow. The property and performance of donor polymers in OSCs are often sensitive to the molecular weight of the polymers. In this study, a chlorinated donor polymer named D18‐Cl is reported, which can achieve high performance with a wide range of polymer molecular weight. The devices based on D18‐Cl show a higher open‐circuit voltage ( V OC ) due to the slightly deeper energy levels and an outstanding short‐circuit current density ( J SC ) owing to the appropriate long periods of blend films and less ([6,6]‐phenyl‐C71‐butyric acid methyl ester) (PC 71 BM) in mixed domains, leading to the higher efficiency of 17.97% than those of the D18‐based devices (17.21%). Meanwhile, D18‐Cl can achieve high efficiencies (17.30–17.97%) when its number‐averaged molecular weight ( M n ) is ranged from 45 to 72 kDa. In contrast, the D18‐based devices only exhibit relatively high efficiencies in a narrow M n range of ≈70 kDa. Such property and performance make D18‐Cl a promising donor polymer for scale‐up and low‐cost production.
Timescales of excited state relaxation in α–RuCl 3 observed by time-resolved two-photon photoemission spectroscopy
The nonequilibrium properties of strongly correlated materials present a target in the search for new phases of matter. It is important to observe the types of excitations that exist in these materials and their associated relaxation dynamics. We have studied the photoexcitations in a spin-orbit assisted Mott insulator α–RuCl 3 using time-resolved two-photon photoemission spectroscopy and transient reflection spectroscopy. We find that photoexcited carriers (doublons) in the upper Hubbard band rapidly relax to Mott-Hubbard excitons on a timescale of less than 200 fs. Subsequently, further relaxation of these lower-energy quasiparticles occurs with an energy-dependent time constant of that ranges from 370 to 600 fs due to exciton cooling. The population of Mott-Hubbard excitons persists for timescales up to several microseconds.
A Difluoro‐Monobromo End Group Enables High‐Performance Polymer Acceptor and Efficient All‐Polymer Solar Cells Processable with Green Solvent under Ambient Condition
Abstract In this paper, a difluoro‐monobromo end group is designed and synthesized, which is then used to construct a novel polymer acceptor (named PY2F‐T) yielding high‐performance all‐polymer solar cells with 15.22% efficiency. The fluorination strategy can increase the intramolecular charge transfer and interchain packing of the previous PY‐T based acceptor, and significantly improve photon harvesting and charge mobility of the resulting polymer acceptor. In addition, detailed morphology investigations reveal that the PY2F‐T‐based blend shows smaller domain spacing and higher domain purity, which significantly suppress charge recombination as supported by time‐resolved techniques. These polymer properties enable simultaneously enhanced J SC and FF of the PY2F‐T‐based devices, eventually delivering device efficiencies of over 15%, significantly outperforming that of the devices based on the non‐fluorinated PY‐T polymer (13%). More importantly, the PY2F‐T‐based active layers can be processed under ambient conditions and still achieve a 14.37% efficiency. They can also be processed using non‐halogenated solvent o ‐xylene (no additive) and yield a decent performance of 13.05%. This work demonstrates the success of the fluorination strategy in the design of high‐performance polymer acceptors, which provide guidelines for developing new all‐PSCs with better efficiencies and stabilities for commercial applications.