Search NASA⌕ Search

Engineering topics

Agnone, A. M.

Publications and source records attributed to Agnone, A. M..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Aerodynamics of slender finned bodies at large angles of attack

In certain missions finned missiles perform slewing maneuvers. Here, large angles of attack are attained. Experimental data needed to understand the aerodynamics of such vehicles are presented. The purpose of this investigation was to study the interaction of the body flow field with that produced by the fins and the resulting effects on the aerodynamic forces and moments. The experiments were conducted at a nominal Mach number of 2.7 and angles of attack from 0 to 50 deg, with two different models. The tests were performed in a range of Reynolds number from 1.5 x 10 to the 6th to 4 x 10 to the 7th per foot (to cover both the laminar and fully turbulent regimes.) Several fin roll angles were investigated. Static pressures on both body and fin surfaces are reported.

Agnone, A. M.↗
NASA NTRS1977

Premixed flame propagation characteristics in a supersonic airstream

Measured values of flame angles are presented to aid the design of premixed combustion chambers and prediction of flame propagation. Flame spread, velocity, and dependence of burning rate on the properties of unburned flow and on turbulence levels are compared with the measured values. The premixed flame angle is found proportional to the amount of heat released, and correlates readily with the fuel mixture ratio through the rate of heat release or rate of water formation. Finite rate combustion affects flame angle mostly at off-stoichiometric conditions. The pilot affects the flame angle if abundant unburnt fuel is present in the pilot hot gases. Viscosity runs several times over the rated level.

Agnone, A. M.↗
NASA NTRS1975

Experimental and analytical study of an inlet forebody for an airframe-integrated scramjet concept

Preliminary analytical and experimental inlet forebody investigations have been conducted at Mach numbers of 6.0 and 8.5. The forebody design concept consisted of a sharp-nosed right circular cone followed by elliptical cross sections. This concept resulted in swept isentropic compression which would allow swept cowl leading edges. Measurements were made to define the condition of the inviscid flow field developed by the forebody, including flow profiles in the vicinity of cowl leading-edge stations, and the three-dimensional boundary-layer effects. The investigation verified some of the expected differences between the predicted and the experimental results.

Andrews, E. H., Jr.↗
NASA NTRS1974

Heat conduction controlled combustion for scramjet applications

The use of heat conduction flame generated in a premixed supersonic stream is discussed. It is shown that the flame is controlled initially by heat conduction and then by chemical reaction. Such a flame is shorter than the diffusion type of flame and therefore it requires a much shorter burner. The mixing is obtained by injecting the hydrogen in the inlet. Then the inlet can be cooled by film cooling.

Ferri, A.↗
NASA NTRS1972

Scramjet fuel injector design parameters and considerations: Development of a two-dimensional tangential fuel injector with constant pressure at the flame

The factors affecting a tangential fuel injector design for scramjet operation are reviewed and their effect on the efficiency of the supersonic combustion process is evaluated using both experimental data and theoretical predictions. A description of the physical problem of supersonic combustion and method of analysis is followed by a presentation and evaluation of some standard and exotic types of fuel injectors. Engineering fuel injector design criteria and hydrogen ignition schemes are presented along with a cursory review of available experimental data. A two-dimensional tangential fuel injector design is developed using analyses as a guide in evaluating the effects on the combustion process of various initial and boundary conditions including splitter plate thickness, injector wall temperature, pressure gradients, etc. The fuel injector wall geometry is shaped so as to maintain approximately constant pressure at the flame as required by a cycle analysis. A viscous characteristics program which accounts for lateral as well as axial pressure variations due to the mixing and combustion process is used in determining the wall geometry.

Agnone, A. M.↗
NASA NTRS1972

Description of a computer program to calculate reacting supersonic internal flow fields with shock waves using viscous characteristics: Program manual and sample calculations

A computer program for calculating internal supersonic flow fields with chemical reactions and shock waves typical of supersonic combustion chambers with either wall or mid-stream injectors is described. The usefulness and limitations of the program are indicated. The program manual and listing are presented along with a sample calculation.

Cavalleri, R. J.↗