Nuclear microreactors and thermal integration with hydrogen generation processes
Not provided.
Nuclear Science & Technology↗
Engineering topics
Ahmed, Zayed
Publications and source records attributed to Ahmed, Zayed.
Helium-air mixing in simulated reactor cavities of high temperature gas reactors
Not provided.
Nuclear Science & Technology↗
The Thermal Response of a Packed Bed Thermal Energy Storage System upon Saturated Steam Injection Using Distributed Temperature Sensing
The effectiveness of a thermal energy storage (TES) system is typically characterized with the help of thermal stratification or temperature gradients along the direction of heat injection, which is typically the flow direction of heat transfer fluid. The steepness of temperature gradients are a direct indicator of the effectiveness or efficiency of the heat storage or dispatch process. The temperature gradient evolution along the packed bed of ceramic particles upon saturated steam injection is presented in this work. Distributed temperature sensing based on optical frequency domain reflectometry was deployed in a packed bed of ceramic particles to capture the thermal front evolution in the axial direction. The physical processes accompanying steam injection in packed beds are complex due to phase change, transitioning two-phase flow, and changes in condensate accumulation. Therefore, the variation of thermal response of the TES system for various steam injection flow rates was experimentally studied using a high-resolution distributed temperature sensing system in a chemically inert alumina particle-packed bed. Distinct zones of different heat transfer modes were observed during the steam injection experiments. A distinct conduction zone, evident from diffuse thermal fronts, was observed at low flow rates, and these thermal gradients became sharper as the flow rate increased. The diffuse thermal fronts in the heat storage media suggest a low exergy efficiency of the TES system, as energy losses started initiating before a significant fraction of the bed was saturated with steam.
25 ENERGY STORAGE↗
Influence of dissolved salts and impurities on seawater on heat transfer and fluid flow through fuel channels and debris bed
This project aims to better understand this mechanism and its effect on heat transfer. Specifically, experimental research was conducted to investigate the long term coolability issues in scaled test setups. Advanced diagnostic and measurement techniques were investigated and incorporated into an annular test facility and a debris bed test facility. The diagnostic techniques investigated included: radioactively tagged salt solution, Frisch collar radiation detector array, neutron and x-ray imaging systems, and a Rayleigh backscatter-based fiber-optic temperature system. Models were checked against the in-situ experimental data and recommendations were made for modeling purposes.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Experimental investigation on the coolability of nuclear reactor debris beds using seawater
During the Fukushima nuclear reactor accident, seawater was injected into the reactor core to cool the decay heat from the heat generating porous debris bed. However, the impact of dissolved salts in water on the coolability of a debris bed is not well understood. This paper is one of the first works to investigate the cooling mechanisms for debris bed using seawater. An experimental system was built where the packed bed test section was volumetrically heated via a high frequency induction heater. The temperature along the axis of the test section was measured using a high resolution temperature sensor based on Optical Frequency Domain Reflectometry. Experimental results show that the dryout heat flux increases with an increase in concentration, with pure water having a dryout volumetric heat flux of 1.8 MW/m and salt water of concentration 7% having a dryout volumetric heat flux of 2.8 MW/m. However, this enhanced coolability using salt water is short term, as the crystallization fouling mechanism becomes significant over time and leads to gradual temperature excursion in the bed. The fouling mechanism eventually leads to a cross section of the debris bed to plug with the deposited salts, and this leads to a pressure build up in the lower regions of the debris bed.
21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
X-ray Imaging-Based Void Fraction Measurement in Saturated Flow Boiling Experiments with Seawater Coolant
Recent studies have shown that the presence of dissolved salts in water can exhibit peculiar flow boiling and two-phase flow regimes. Two-phase flow and convective flow boiling are typically characterized with the help of void fraction measurements. To quantitatively improve our understanding of two-phase flow and boiling phenomenon with seawater coolant, void fraction data are needed, which can not be obtained from optical imaging. In this paper, we present experimental void fraction measurements of saturated flow boiling of tap water and seawater using X-ray radiography. X-rays with a maximum energy level of 40 KeV were used for imaging the exit region of the heated test section. At lower heat flux levels, the two phase flow in seawater was bubbly and homogeneous in nature, resulting in higher void fractions as compared to tap water. With an increase in heat flux, the flow regime was similar to slug flow, and void fraction measurements approached similarity with tap water. The predicted pressure drop using the measured void faction shows good agreement with the measured total pressure drop across the test section, demonstrating the validity of the measurement process.
Eckels, Seth↗
Impact of dissolved salts on two-phase flow and boiling heat transfer in a natural circulation loop
Two-phase natural circulation and boiling experiments are conducted in this study with artificial seawater as a heat transfer fluid or process coolant. This experimental work is focused on understanding the role of dissolved salts in water on the steady state two-phase natural circulation flow rates. Mass flow rates were measured at different heat flux levels with artificial seawater, deionized water and tap water in the experimental loop. It was found that the average quasi-steady state mass flow rates were the same at any particular heat flux level regardless of the fluid being used. Artificial seawater coolant exhibited more stable natural circulation at higher heat flux as compared to the other two coolants. Mass flow measurements recorded at 2 s intervals show that magnitude of flow oscillations are much higher in case of tap water and deionized water. Also, high speed camera images revealed that the bubble departure diameters are smaller in seawater compared to tap or deionized water. This can be attributed to the increased local wettability due to the presence of dissolved salts in the fluid. Visual observations of the riser section showed that bubble coalescence and formation of slugs is inhibited in the seawater. These observations also explain the reduced pressure drop across test section when seawater was used as a coolant.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗