Search NASA⌕ Search

Engineering topics

Aiken, T. N.

Publications and source records attributed to Aiken, T. N..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Wind-tunnel investigation of a large-scale VTOL aircraft model with wing root and wing thrust augmentors

Tests were conducted in the Ames 40 by 80 foot wind tunnel to determine the aerodynamic characteristics of a large-scale V/STOL aircraft model with thrust augmentors. The model had a double-delta wing of aspect ratio 1.65 with augmentors located in the wing root and the wing trailing edge. The supply air for the augmentor primary nozzles was provided by the YJ-97 turbojet engine. The airflow was apportioned approximately 74 percent to the wing root augmentor and 24 percent to wing augmentor. Results were obtained at several trailing-edge flap deflections with the nozzle jet-momentum coefficients ranging from 0 to 7.9. Three-component longitudinal data are presented with the agumentor operating with and without the horizontal tail. A limited amount of six component data are also presented.

Aoyagi, K.↗
NASA NTRS1979

Aerodynamic characteristics of a large-scale semispan model with a swept wing and an augmented jet flap with hypermixing nozzles

The aerodynamic characteristics of the augmentor wing concept with hypermixing primary nozzles were investigated. A large-scale semispan model in the Ames 40- by 80-Foot Wind Tunnel and Static Test Facility was used. The trailing edge, augmentor flap system occupied 65% of the span and consisted of two fixed pivot flaps. The nozzle system consisted of hypermixing, lobe primary nozzles, and BLC slot nozzles at the forward inlet, both sides and ends of the throat, and at the aft flap. The entire wing leading edge was fitted with a 10% chord slat and a blowing slot. Outboard of the flap was a blown aileron. The model was tested statically and at forward speed. Primary parameters and their ranges included angle of attack from -12 to 32 degrees, flap angles of 20, 30, 45, 60 and 70 degrees, and deflection and diffuser area ratios from 1.16 to 2.22. Thrust coefficients ranged from 0 to 2.73, while nozzle pressure ratios varied from 1.0 to 2.34. Reynolds number per foot varied from 0 to 1.4 million. Analysis of the data indicated a maximum static, gross augmentation of 1.53 at a flap angle of 45 degrees. Analysis also indicated that the configuration was an efficient powered lift device and that the net thrust was comparable with augmentor wings of similar static performance. Performance at forward speed was best at a diffuser area ratio of 1.37.

Aiken, T. N.↗
NASA NTRS1977

Thrust augmentor application for STOL and V/STOL

A general parametric description is suggested for thrust augmentor application to STOL and V/STOL aircraft. The parameters and their relationships are discussed using several aircraft augmentor integration problems. For a STOL transport design, the ram drag is a key consideration, limiting the maximum gross augmentation that can be utilized. Maximizing gross augmentation and balancing the aircraft are key considerations for a V/STOL fighter design. Results from wind tunnel investigations on several different thrust augmentor concepts and system studies on STOL transport designs are also included.

Aiken, T. N.↗
NASA NTRS1977

Large-scale V/STOL testing

Several facets of large-scale testing of V/STOL aircraft configurations are discussed with particular emphasis on test experience in the Ames 40- by 80-Foot Wind Tunnel. Examples of powered-lift test programs are presented in order to illustrate tradeoffs confronting the planner of V/STOL test programs. Large-scale V/STOL wind-tunnel testing can sometimes compete with small-scale testing in the effort required (overall test time) and program costs because of the possibility of conducting a number of different tests with a single large-scale model where several small-scale models would be required. The benefits of both high- or full-scale Reynolds numbers, more detailed configuration simulation, and number and type of onboard measurements are studied.

Koenig, D. G.↗
NASA NTRS1977

Large-scale V/STOL testing

Several facets of large-scale testing of V/STOL aircraft configurations are discussed with particular emphasis on test experience in the Ames 40- by 80-foot wind tunnel. Examples of powered-lift test programs are presented in order to illustrate tradeoffs confronting the planner of V/STOL test programs. It is indicated that large-scale V/STOL wind-tunnel testing can sometimes compete with small-scale testing in the effort required (overall test time) and program costs because of the possibility of conducting a number of different tests with a single large-scale model where several small-scale models would be required. The benefits of both high- and full-scale Reynolds numbers, more detailed configuration simulation, and number and type of onboard measurements increase rapidly with scale. Planning must be more detailed at large scale in order to balance the trade-offs between the increased costs, as number of measurements and model configuration variables increase and the benefits of larger amounts of information coming out of one test.

Koenig, D. G.↗
NASA NTRS1977

Validation of AV-8B V/STOL characteristics by full scale static and wind tunnel tests

The background which led to the requirement for the full scale powered wind tunnel tests of an AV-8B model, and the formulation of specific objectives for the test, are outlined. The detailed planning, analysis, and coordination with NASA, NAVAIR, and other industry participants is described. The modification of an AV-8A Harrier into an AV-8B configuration suitable for full scale testing at Ames is described. In addition, instrumentation and data systems are explained. Operations during the 40 ft x 80 ft wind tunnel testing and the resulting propulsion, aerodynamic, performance, stability and control data are presented and suggestions offered for future V/STOL testing.

Hollingsworth, E. G.↗
NASA NTRS1976

Correlation of internal surface turbulence with far-field noise of the augmentor wing propulsive-lift concept

A wind tunnel investigation was conducted to determine the nature, strength, and variation with airspeed of the acoustic sources of the augmentor wing propulsive-lift concept. The augmentor wing overall noise is dominated by the high frequency jet mixing noise characteristic of the lobed primary nozzle. The augmentor modifies the intensity and propagation characteristics of the jet sources, especially those that exist inside the augmentor. The interaction of the turbulent flow with the augmentor creates low-frequency, low-intensity surface noise and trailing edge noise. These sources dominate any jet mixing noise that is present at the low frequencies and could become significant if the jet noise was suppressed by treating the augmentor with a lining tuned to the jet noise source location. The far-field noise of the untreated augmentor is unaffected by airspeed; however, this may not be the case when the jet noise is suppressed, because the trailing edge surface pressure and correlations with far-field noise do show a reduction with forward speed.

Falarski, M. D.↗
NASA NTRS1975

Acoustic characteristics of a large scale wind-tunnel model of a jet flap aircraft

The expanding-duct jet flap (EJF) concept is studied to determine STOL performance in turbofan-powered aircraft. The EJF is used to solve the problem of ducting the required volume of air into the wing by providing an expanding cavity between the upper and lower surfaces of the flap. The results are presented of an investigation of the acoustic characteristics of the EJF concept on a large-scale aircraft model powered by JT15D engines. The noise of the EJF is generated by acoustic dipoles as shown by the sixth power dependence of the noise on jet velocity. These sources result from the interaction of the flow turbulence with flap of internal and external surfaces and the trailing edges. Increasing the trailing edge jet from 70 percent span to 100 percent span increased the noise 2 db for the equivalent nozzle area. Blowing at the knee of the flap rather than the trailing edge reduced the noise 5 to 10 db by displacing the jet from the trailing edge and providing shielding from high-frequency noise. Deflecting the flap and varying the angle of attack modified the directivity of the underwing noise but did not affect the peak noise. A forward speed of 33.5 m/sec (110 ft/sec) reduced the dipole noise less than 1 db.

Falarski, M. D.↗
NASA NTRS1974

Comparison of the acoustic characteristics of large-scale models of several propulsive-lift concepts

Wind-tunnel acoustic investigations were performed to determine the acoustic characteristics and the effect of forward speed on the over-the-wing externally blown jet flap (OTW), the under-the-wing externally blown jet flap (UTW), the internally blown jet flap (IBF), and the augmentor wing (AW). The data presented represent the basic noise generated by the powered-lift system without acoustic treatment, assuming all other noise sources, such as the turbofan compressor noise, have been suppressed. Under these conditions, when scaled to a 100,000-lb aircraft, the OTW concept exhibited the lowest perceived noise levels, because of dominant low-frequency noise and wing shielding of the high-frequency noise. The AW was the loudest configuration, because of dominant high-frequency noise created by the high jet velocities and small nozzle dimensions. All four configurations emitted noise 10 to 15 PNdB higher than the noise goal of 95 PNdB at 500 ft.

Falarski, M. D.↗
NASA NTRS1974

Evaluation of a new jet flap propulsive-lift system for turbofan-powered STOL transports

A large-scale STOL transport model with a new jet flap propulsive-lift system was subject to wind-tunnel testing. Aerodynamically, this IBF system combines the benefits of the jet flap and the mechanical flap with boundary layer control. Structurally, it creates its own spanwise air duct with the deflection of the mechanical flap. An additional short-chord control flap, located at the jet-flap exit, provides a powerful means for flight path and lateral controls. The results show that the overall effectiveness of this flap system compares well with other jet flap propulsive-lift systems. A preliminary study based on the wind-tunnel data was made on a medium-size IBF STOL jet transport configuration for a typical-military mission. This study showed that the IBF results in a configuration with a relatively low T/W ratio, making the system an attractive candidate for future designs.

Chin, Y. T.↗
NASA NTRS1973

Aerodynamic characteristics of a large-scale model with a swept wing and a jet flap having an expandable duct

The data from an investigation of the aerodynamic characteristics of the expandable duct-jet flap concept are presented. The investigation was made using a large-scale model in the Ames 40- by 80-foot Wind Tunnel. The expandable duct-jet flap concept uses a lower surface, split flap and an upper surface, Fowler flap to form an internal, variable area cavity for the blowing air. Small amounts of blowing are used on the knee of the upper surface flap and the knee of a short-chord, trailing edge control flap. The bulk of the blowing is at the trailing edge. The flap could extend the full span of the model wing or over the inboard part only, with blown ailerons outboard. Primary configurations tested were two flap angles, typical of takeoff and landing; symmetric control flap deflections, primarily for improved landing performance; and asymmetric aileron and control flap deflections, for lateral control.

Aiken, T. N.↗
NASA NTRS1973

Aerodynamic and noise measurements on a quasi-two dimensional augmentor wing model with lobe-type nozzles

An investigation was made of the static, wind-on aerodynamic and static noise characteristics of an augmentor wing having lobe type nozzles. The study was made in the Ames 7-by 10-Foot No. 1 Wind Tunnel using a small-scale, quasi-two-dimensional model. Several configurations of lobe nozzles as well as a normal slot nozzle were tested. Results indicate that lobe nozzles offer improved static and wind-on aerodynamics and reduced static noise relative to slot nozzles. Best wind-on performance was obtained when the tertiary gap was closed even though the static thrust augmentation was maximum with the gap open. Static thrust augmentation, wind-on lift and drag, and static noise directivity are presented as well as typical static and wind-on exit velocity profiles, surface pressure distributions and noise spectrums. The data are presented with limited discussion.

Aiken, T. N.↗
NASA NTRS1973

Results of Full-Scale Wind Tunnel Tests on the H.126 Jet Flap Aircraft

The aerodynamic characteristics of the full-scale H.126 jet flap aircraft were studied in a 40- by 80 foot wind tunnel. The H.126 aircraft is designed for research on flight characteristics of an aircraft using the jet flap principle. Static longitudinal, lateral, and directional characteristics were measured at a Reynolds number of 2.5 to 2.7 million. The jet control power as well as the aerodynamic characteristics were measured and are presented herein with limited discussion. The primary configuration variables were flap and aileron deflection.

Aiken, T. N.↗
NASA NTRS1972

Advanced augmentor-wing research

Results of research on advanced augmentors are discussed. Research concerned with performance indicated that: (1) augmentors with lobe-type nozzles give higher thrust augmentation than those with slot-type primary nozzles; (2) the thrust of augmentor wings at forward speed is greater than that of internally blown flaps for the speed range of interest; and (3) the optimum augmentor geometry at forward speed may be different from the optimum static geometry. Analysis of augmentor-wing data shows that the data may be correlated by accounting for the augmentation and entrainment in defining a net thrust coefficient.

Aiken, T. N.↗
NASA NTRS1972

Advanced augmentor-wing research

Results of research on advanced augmentors are discussed. Research concerned with performance has indicated that: (1) augmentors with lobe-type nozzles give higher thrust augmentation than those with slot-type primary nozzles, (2) the thrust of augmentor wings at forward speed is greater than that of internally blown flaps for the speed range of interest, and (3) the optimum augmentor geometry at forward speed may be different from the optimum static geometry. Analysis of augmentor-wing data has shown that the data may be correlated by accounting for the augmentation and entrainment in defining a net thrust coefficient.

Aiken, T. N.↗
NASA NTRS1971

Full-scale wind-tunnel tests of a small unpowered jet aircraft with a T-tail

The aerodynamic characteristics of a full scale executive type jet transport aircraft with a T-tail were investigated in a 40 x 80 ft (12.2 by 24.4 meter) wind tunnel (subsonic). Static, longitudinal, and lateral stability, and control characteristics were determined at angles of attack from -2 deg to +42 deg. The aircraft wing had 13 deg of sweep and an aspect ratio of 5.02. The aircraft was tested power off with various wing leading- and trailing-edge high lift devices. The basic configuration was tested with and without such components as engine nacelles, wing tip tanks, and empannage. Hinge-moment data were obtained and downwash angles in the horizontal-tail plane location were calculated. The data were obtained at Reynolds numbers of 4.1 million and 8.7 million based on mean aerodynamic chord. The model had static longitudinal stability through initial stall. Severe tail buffet occurred near the angle of attack for maximum lift. Above initial stall the aircraft had pronounced pitch-up, characteristic of T-tail configurations. A stable trim point was possible at angles of attack between 30 deg and 40 deg (depending on c.g. location and flap setting). Hinge-moment data showed no regions with adverse effects on stick force. Comparisons of wind-tunnel data and flight-test are presented.

Soderman, P. T.↗