Search NASA⌕ Search

Engineering topics

Ainsworth, R.

Publications and source records attributed to Ainsworth, R..

NIOLD Run 4 Report

In this report we discuss the motivation, methods, and analysis of the IOTA Run 4 studies of the Nonlinear Integrable Optics, Landau Damping (NIOLD) experiment. We introduce Landau Damping, an effect that damps collective instabilities in particle accelerators. We also introduce and discuss a new method to measure stability diagrams which quantify the strength of Landau Damping, that employs an antidamper. We also present the data collection process, the data analysis procedure, and the preliminary results. The first results qualitatively agree with the analytical predictions and the simulations. Next steps for the current data and goals for future data are also discussed.

43 PARTICLE ACCELERATORS↗

Optimizing the tuning range of the Fermilab Recycler 53MHz RF cavities by exploiting the avoided crossing of the tuner and cavity modes

The electromagnetic eigenmodes of the Fermilab Recycler RF cavities were simulated with ACE3P running on NERSC's 'Perlmutter' supercomputer in an attempt to optimize their tuning range to comfortably support slip-stacking. A theory, based on coupled circuits and avoided crossings, was developed to explain the origins of the tuning range for tuner-cavity waveguide systems. This provided a logical, rigorous method to carry out this optimization, although engineering problems due to high voltages in the tuner and the operational $\mu$ range of the garnet had to be carefully implemented. It was shown that the desired goal of 10kHz of tuning was not attainable with the current cavity specifications. The maximum tuning range obtained was 5.59kHz for a single tuner with a coaxial line of length 63in. A double tuner cavity was also studied using the simulation software, although with little improvement in the tuning range. A promising technique to improve the tuning range involving the desynchronization of the garnets' magnetic permeabilities is proposed.

43 PARTICLE ACCELERATORS↗

The Ionization Profile Monitors in the Recycler Ring

The ionization profile monitors (IPMs) are used to measure the beam size in synchrotrons. Both the Fermilab Recycler and Main Injector (MI) machines have IPMs. However, they were not well understood enough to provide confidence in their measurements. Accurately measuring beam size through the IPMs was crucial to recognize the loss mechanisms for accelerators and to keep the beam loss to a minimum. Thus, performing measurements with different parameters using the IPMs led to a better analysis on how changes in conditions affect the beam size. The IPM measurements are compared with that of multi-wires in the upstream transfer line after applying corrections. The results were compared with other diagnostics and the change in the beam size for different parameters are presented in this paper.

43 PARTICLE ACCELERATORS↗

Electron Cloud Simulations In The Fermilab Recycler

We present a simulation study to characterize the stability region of the Fermilab (FNAL) Recycler in the context of secondary emission yield (SEY). Interactions between electrons and beam pipe material can produce electron clouds that jeopardize beam stability in certain focusing configurations. Such an instability was documented in the Recycler, and the work presented here reflects improvements to better understand that finding. We incorporated the Furman-Pivi Model into a PyECLOUD analysis, and we determined the instability threshold given various bunch lengths, intensities, SEY magnitudes, and model parameters.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Experimental studies of 7-cell dual axis asymmetric cavity for energy recovery linac

High average current, transportable energy recovery linacs (ERLs) can be very attractive tools for a number of applications including next generation high-luminosity, compact light sources. Conventional ERLs are based on an electron beam circulating through the same set of rf cavity cells. This leads to an accumulation of high-order modes inside the cavity cells, resulting in the development of a beam breakup (BBU) instability, unless the beam current is kept below the BBU start current. This limits the maximum current which can be transported through the ERL and hence the intensity of the photon beam generated. It has recently been proposed that splitting the accelerating and decelerating stages, tuning them separately and coupling them via a resonance coupler can increase the BBU start current. The paper presents the first experimental rf studies of a dual axis 7-cell asymmetric cavity and confirms the properties predicted by the theoretical model. The field structures of the symmetric and asymmetric modes are measured and good agreement with the numerical predictions is demonstrated. The operating mode field flatness was also measured and discussed. A novel approach based on the coupled mode (Fano-like) model has been developed for the description of the cavity eigenmode spectrum and good agreement between analytical theory, numerical predictions and experimental data is shown. Finally, numerical and experimental results observed are analyzed, discussed and a good agreement between theory and experiment is demonstrated.

43 PARTICLE ACCELERATORS↗

Transition Crossing in the Main Injector for PIP-II

Proton Improvement Plan-II (PIP-II) [1] is Fermilab’s plan for providing powerful, high-intensity proton beams to the laboratory’s experiments. PIP II will include upgrades to the Booster, Recycler and Main Injector which will be required to accelerate 50% more beam as well as increasing the Booster repetition rate from 15 to 20 Hz. To accommodate the faster rate, the momentum separation of the slip stacking beams in the Recycler must increase which will result in in larger longitudinal emittance bunches in MI. In order to cross transition without losses, it is expected a gamma-t jump will be needed. Gamma-t jump schemes for the MI are investigated.

Ainsworth, R.↗

Compact, energy efficient superconducting asymmetric ERL for ultra-high fluxes of X-ray and THz

To make the light sources compact and energy efficient, an energy recovery Superconducting RF LINAC can be used. We suggest a dual-axis, asymmetric cavity instead of conventional single axis, symmetric cavity configurations to generate average electron beam currents above 1 A, while still avoiding development of the beam breakup instability (BBU). The use of an asymmetric cavity allows one to increase the start current of HOMs participating in BBU instability development, as well as to break the positive feedback, resulting in the capability of a high average current electron beam to be driven without loss through the system. In this work, the results of experimental studies of an asymmetric cavity are presented and compared with theoretical predictions. The following steps toward design of a full-scale superconducting cavity are also discussed.

43 PARTICLE ACCELERATORS↗

Transition Crossing in the Main Injector for PIP-II

Proton Improvement Plan-II (PIP-II) is Fermilab’s plan for providing powerful, high-intensity proton beams to the laboratory’s experiments. PIP II will include upgrades to the Booster, Recycler and Main Injector which will be required to accelerate 50% more beam as well as increasing the Booster repetition rate from 15 to 20 Hz. To accommodate the faster rate, the momentum separation of the slip stacking beams in the Recycler must increase which will result in in larger longitudinal emittance bunches in MI. In order to cross transition without losses, it is expected a gammat jump will be needed. Gamma-t jump schemes for the MI are investigated

43 PARTICLE ACCELERATORS↗

Resistive Wall Growth Rate Measurements in the Fermilab Recycler

Impedance could represent a limitation of running high intensity beams in the Fermilab recycler. With high intensity upgrades foreseen, it is important to quantify the impedance. To do this,studies have been performed measuring the growth rate of presumably the resistive wall instability. The growth rates at varying intensities and chromaticities are shown. The measured growth rates are compared to ones calculated with the resistive wall impedance.

Ainsworth, R.↗

Fermilab Recycler Collimation System Design

To provide 700 kW proton beams for neutrino production in the NuMI facility, we employ slip stacking in the Recycler with transfer to the Main Injector for recapture and acceleration. Slip stacking with 12 Booster batches per 1.33 sec cycle of the Main Injector has been implemented and briefly tested while extensive operation with 8 batches and 10 batches per MI cycle has been demonstrated. Operation in this mode since 2013 shows that loss localization is an essential component for long term operation. Beam loss in the Recycler will be localized in a collimation region with design capability for absorbing up to 2 kW of lost protons in a pair of 20-Ton collimators (absorbers). This system will employ a two stage collimation with a thin molybdenum scattering foil to define the bottom edge of both the injected and decelerated-for-slipping beams. Optimization and engineering design of the collimator components and radiation shielding are based on comprehensive MARS15 simulations predicting high collimation efficiency as well as tolerable levels of prompt and residual radiation. The system installation during the Fermilab 2016 facility shutdown will permit commissioning in the subsequent operating period.

43 PARTICLE ACCELERATORS↗