Search NASA⌕ Search

Engineering topics

Ajayi, Oyelayo O.

Publications and source records attributed to Ajayi, Oyelayo O..

Improving knife milling performance for biomass preprocessing by using advanced blade materials

Mechanical preprocessing of biomass, including size reduction, is a crucial step in converting biomass into biofuel. However, feedstock inevitably contains abrasive intrinsic and extrinsic inorganics that may cause excessive tool wear in preprocessing. Here, this work demonstrates that performance of a knife mill can be significantly improved by applying a more wear-resistant blade material. A series of full-scale knife mill tests were performed for size reduction of forest residue using blades of tungsten carbide (WC–Co), iron-borided tool steel, and diamond-like carbon (DLC) coated tool steel. Blade material loss was quantified in correlation to the amount of feedstock processed and wear mechanisms were investigated via worn surface characterization. While the thin DLC coating was removed quickly, the WC-Co and iron-borided blades improved the tool life by 8X and 3X compared with the M2 tool steel blades (baseline), respectively. The in-situ throughput and power consumption measurements provided additional insights. The WC-Co and iron-borided blades had ~3X higher throughput than the baseline blades by the end of the test with lower normalized power consumption. The experimental results were then used as input for a techno-economic analysis, which suggested that the more wear resistant blades could cut the knife milling cost by $2–3 per ton of biomass processed with downtime reduced by 65–85%.

36 MATERIALS SCIENCE↗

Effect of Moisture and Feedstock Variability on the Rheological Behavior of Corn Stover Particles

Continuous feeding, processing, and handling of biomass powders is pivotal to the economic viability of integrated biorefineries. However, current challenges associated with the operational reliability of bulk solids handling and transport greatly impact the process economics and ultimately the widespread commercialization of integrated biorefineries. In this work, we examine the effect of moisture and feedstock variability on the flow behavior of corn stover biomass particles. The total flow energy, compressibility, shear properties, and wall friction angles were measured for corn stover samples A and B containing 0%, 15%, 25%, 50%, and 75% (mass fraction) moisture contents using a FT4 powder rheometer. In general, the flowability of both A and B was reduced when moisture was present as indicated by the stability and variable flow rate, compressibility, and shear tests. The 15% moisture sample had the highest flow energy, revealing the interplay between the increased surface tension and looser packing both of which were caused by liquid bridging. The 75% moisture sample had the highest compressibility and the lowest flowability factor (ff c ). The trend in wall friction angle was found to be dependent upon the surface hydrophobicity of the wall material. The wall friction angle on the hydrophilic, stainless-steel surface increased with moisture and therefore poses additional handling challenges. On the other hand, the wall friction angle on the hydrophobic polymer surfaces were the lowest for samples with intermediate moisture contents. Sample B had greater bulk density, smaller compressibility, and greater flowability than the sample A , as suggested by the compressibility and shear tests. The wall friction angle of sample B was higher than or equal to that of sample A depending on both the type and the surface roughness of the wall material.

09 BIOMASS FUELS↗

Flow behavior characterization of biomass Feedstocks

With the advancement of renewable energy, the processing and handling of biomass feedstocks has drawn enormous research interest. The key to economically viable and operationally reliable biomass handling processes involves a complete understanding of the flow behavior of different feedstocks as functions of the inherent critical material properties environmental conditions, and critical processing parameters. This review introduces the basic principles and methods in bulk solids flow and highlights recent efforts to understand the flow behavior of biomass feedstocks. The effects of inherent properties, environmental parameters, and handling equipment on the flow behavior of biomass feedstocks are presented. Particle size, shape, moisture, consolidation stress, temperature, storage time at rest, chemical treatment, and the material and geometry of the handling equipment all substantially influence biomass flowability. The limitations of current studies and the potential methods to overcome them are presented. Finally, an outlook for future research effort is provided, with proposed opportunities for improving the characterization of biomass flow.

Bulk solids testing↗

Assessment of a tomography-informed polyhedral discrete element modelling approach for complex-shaped granular woody biomass in stress consolidation

The design of handling equipment for granular biomass primarily requires experiments. Discrete element models (DEM) can provide designers with detailed insight into the behaviour of granular materials. However, granular biomass comprising complex-shaped particles is difficult to model with DEM. A tomography-informed DEM approach and an exhaustive assessment of the ability of the approach to predict the bulk behaviour of milled pines using experimental data is presented. Nano-CT scan was conducted to obtain 3D particle surface geometries as the basis for particle shape approximation by a polyhedral model and a sphero-polyhedral model. These models were applied in the simulation of a compressibility test. Our parametric study showed that particle Young's modulus and restitution coefficient are the two main properties influencing the simulated bulk behaviour of the DEM particles and that the level of approximating DEM particle shape for real particles is critical for accurately replicating the bulk behaviour of milled pines. The polyhedral model demonstrated better suitability than its sphero-polyhedral counterpart for modelling pine particles. The polyhedral model calibrated in a compressibility test was then applied in the simulations of a friction test without additional parameter tuning. Interlocking was dominant in the shear of bulk pine particles. Remarkably, the polyhedral model predicted the frictional behaviour of the pine particles when compared to the experimental results. The limitations of the model, as well as possible ways for enhancement, are discussed. This work provided novel insights into the suitability of complex-shaped DEM models for granular woody biomass.

Biomass flow↗

Mechanical processing of metallic component surfaces

A method of mechanically processing a metallic material component is provided whereby alloying, carburizing, nitriding and boriding can be performed using a friction stir processing tool. This method for mechanically processing metallic material surfaces is cost effective, efficient and does not require specialized equipment.

36 MATERIALS SCIENCE↗

Experimental Evaluation of Oxide Nanoparticles as Friction and Wear Improvement Additives in Motor Oil

The effect of two nanoparticle oxides on friction and wear was studied under laboratory test conditions using a reciprocating test machine and two test configurations. The addition of these nanoparticles in base stock oil under certain conditions reduced the coefficient of friction and improved wear, but that depended on the test configuration. Examination of the rubbed surfaces showed the pronounced formation of a tribofilm in some cases, while polishing on the surface was also observed in other cases. Contact configuration is important when oxide nanoparticles are being evaluated and the conclusions about their efficacy can be vastly different.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tribological synthesis method for producing low-friction surface film coating

An article of method of manufacture of a low friction tribological film on a substrate. The article includes a substrate of a steel or ceramic which has been tribologically processed with a lubricant containing selected additives and the additives, temperature, load and time of processing can be selectively controlled to bias formation of a film on the substrate where the film is an amorphous structure exhibiting highly advantageous low friction properties.

36 MATERIALS SCIENCE↗

Bio-derived Fuel Blend Dilution of Marine Engine Oil and Imapct on Friction and Wear Behavior

To reduce the amount of petroleum-derived fuel used in vehicles and vessels powered by internal combustion engines, the addition of bio-derived fuel extenders is a common practice. Ethanol is perhaps the most common bio-derived fuel used for blending, and butanol is being evaluated as a promising alternative. The present study determined the fuel dilution rate of three lubricating oils (E0, E10, and i-B16) in a marine engine operating in on-water conditions with a start-and-stop cycle protocol. The level of fuel dilution increased with the number of cycles for all three fuels. The most dilution was observed with i-B16 fuel, and the least with E10 fuel. In all cases, fuel dilution substantially reduced the oil viscosity. The impacts of fuel dilution and the consequent viscosity reduction on the lubricating capability of the engine oil in terms of friction, wear, and scuffing prevention were evaluated by four different tests protocols. Although the fuel dilution of the engine oil had minimal effect on friction, because the test conditions were under the boundary lubrication regime, significant effects were observed on wear in many cases. Fuel dilution also was observed to reduce the load-carrying capacity of the engine oils in terms of scuffing load reduction.

Ajayi, Oyelayo O.↗

Experimental Investigation of Friction and Wear Behavior of 304L Stainless Steel Sliding Against Different Counterface in Dry Contact

In this study, friction and wear behavior of 304L stainless steel sliding against different ball counterface under dry contact was investigated. Tests were conducted using a ball-on-flat contact configuration in reciprocating sliding with 440C stainless steel, Al alloy (2017) and bronze ball counterfaces under different loads. Detailed surface analysis was also done using 3-D profilometry technique and optical microscopy in order to determine wear mechanism and dimension. All the pairs exhibited initial rapid increase in coefficient of friction after which a variety of friction behavior, depending on the ball counterface, was observed. The flat and the ball counterface in 304L stainless steel-440C stainless steel pair showed wear that was proportional to applied load. In both 304L stainless steel-Al alloy (2017) and 304L stainless steel-bronze pairs, ball samples showed severe wear that was proportional to the applied load while material transfer from the different balls occurred in the flat. The study concluded that friction and wear were not material properties but a kind of responses that characterize a pair of surfaces in contact undergoing relative motion.

Olofinjana, Bolutife↗

Rapid surface hardening and enhanced tribological performance of 4140 steel by friction stir processing

Tribological performance of steel materials can be substantially enhanced by various thermal surface hardening processes. For relatively low-carbon steel alloys, case carburization is often used to improve surface performance and durability. If the carbon content of steel is high enough (>0.4%), thermal treatments such as induction, flame, laser, etc. can produce adequate surface hardening without the need for surface compositional change. This paper presents an experimental study of the use of friction stir processing (FSP) as a means to hardened surface layer in AISI 4140 steel. The impacts of this surface hardening process on the friction and wear performance were evaluated under both dry and lubricated contact conditions in reciprocating sliding. FSP produced the same level of hardening and superior tribological performance when compared to conventional thermal treatment, using only 10% of the energy and without the need for quenching treatments. With FSP surface hardness of about 7.8 GPa (62 Rc) was achieved while water quenching conventional heat treatment produced about 7.5 GPa (61 Rc) hardness. Microstructural analysis showed that both FSP and conventional heat treatment produced martensite. Although the friction behavior for FSP treated surfaces and the conventional heat treatment were about the same, the wear in FSP processed surfaces was reduced by almost 2× that of conventional heat treated surfaces. Furthermore, the superior performance is attributed to the observed grain refinement accompanying the FSP treatment in addition to the formation of martensite. As it relates to tribological performance, this study shows FSP to be an effective, highly energy efficient, and environmental friendly (green) alternative to conventional heat treatment for steel.

36 MATERIALS SCIENCE↗

Effect of laser surface texturing (LST) on tribochemical films dynamics and friction and wear performance

Surface texturing or topographical design is one of the primary techniques to control friction and wear performance of surfaces in tribological contact. Laser surface texturing (LST), whereby a laser beam is used to produce regular arrays of dimples on a surface, has been demonstrated to reduce friction in conformal lubricated contacts. Friction and wear behavior under boundary lubrication is also known to be dependent on the formation and durability of the tribochemical film formed from lubricant additives. In this paper, the effects of LST on the formation and durability of tribochemical films and its consequent impacts on friction and wear behavior in various lubrication regimes were evaluated. Friction and wear tests that cycled through different lubrication regimes were conducted with both polished and LST treated surfaces using a synthetic lubricant with and without model additives of ZDDP and MoDTC mixture. In the base oil without additives, LST produced noticeable reduction in friction in all lubrication regimes. However, with low-friction model additives, friction was higher in tests with LST due to significant differences in the tribochemical film formation in the polished and LST surfaces, as well as the sliding counterface. Continuous tribo-films were formed on ball conterface rubbed against polished surfaces while the films were streaky and discontinuous in ball rubbed against LST surfaces. LST produced more wear on the ball counterface in both base and additized oils. Lastly, no measurable wear was observed in both the polished and LST flat specimens.

36 MATERIALS SCIENCE↗

Modulated composite surfaces

Methods and compositions relating to the preparation of structurally and compositionally modulated composite surfaces that can potentially reduce friction and increase resistance to wear and scuffing in rolling, rotating and sliding bearing applications. Preparation of nano-to-micro size pores, holes, or dimples on a given solid surface and filling them with soft or hard coatings at desired thickness to achieve such properties.

Erdemir, Ali↗