Search NASA⌕ Search

Engineering topics

Alam, Muhammad A.

Publications and source records attributed to Alam, Muhammad A..

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Two-dimensional perovskite templates for durable, efficient formamidinium perovskite solar cells

We present a design strategy for fabricating ultrastable phase-pure films of formamidinium lead iodide (FAPbI 3 ) by lattice templating using specific two-dimensional (2D) perovskites with FA as the cage cation. When a pure FAPbI 3 precursor solution is brought in contact with the 2D perovskite, the black phase forms preferentially at 100°C, much lower than the standard FAPbI 3 annealing temperature of 150°C. X-ray diffraction and optical spectroscopy suggest that the resulting FAPbI 3 film compresses slightly to acquire the (011) interplanar distances of the 2D perovskite seed. The 2D-templated bulk FAPbI 3 films exhibited an efficiency of 24.1% in a p-i-n architecture with 0.5–square centimeter active area and an exceptional durability, retaining 97% of their initial efficiency after 1000 hours under 85°C and maximum power point tracking.

14 SOLAR ENERGY↗
DOE OSTI2022

Worldwide Physics-Based Lifetime Prediction of c-Si Modules Due to Solder-Bond Failure

Lifetime prediction of the fielded c-Si solar modules due to location-specific weather conditions has been an important topic of photovoltaic research and the economic viability of solar energy. Data analytic techniques such as the performance ratio method, Statistical clear sky model, and Suns-Vmp methods quantify the degradation from measured data of a solar farm, however, the nonlinear time-dependence and correlated degradations make it difficult to use the empirical degradation rates for ultimate lifetime projection. In this article, we propose a complementary physics-based model to predict the solder bond failure caused by mechanical stress associated with the variations of the temperature. Integrating the worldwide weather information from NASA/NSRDB databases, the model predicts the location-specific output-power degradation and the lifetime of a module due to solder bond failure. The model parameters are calibrated against qualification tests involving thermal cycling of specific batches of modules from a specific technology/manufacturer. The results may be summarized as: 1) Modules installed at higher latitudes show a longer lifetime due to reduced damage accumulation. 2) The reduction of temperature fluctuation close to large bodies of water, such as seashores, increases solder bond lifetime significantly. 3) Relatively speaking, modules installed close to the Tropic of Cancer/Capricorn (23.5 degrees North/South) suffer from a higher solder bond damage and have a shorter lifetime, suggesting a conservative design. This model should serve as a building block of a comprehensive reliability framework that can predict the lifetime of a module that experiences simultaneous and correlated degradation mechanisms involving yellowing, corrosion, and potential-induced degradation.

14 SOLAR ENERGY↗
DOE OSTI2021

Light-activated interlayer contraction in two-dimensional perovskites for high-efficiency solar cells

Understanding and tailoring the physical behaviour of halide perovskites under practical environments is critical for designing efficient and durable optoelectronic devices. Here, we report that continuous light illumination leads to >1% contraction in the out-of-plane direction in two-dimensional hybrid perovskites, which is reversible and strongly dependent on the specific superlattice packing. X-ray photoelectron spectroscopy measurements show that constant light illumination results in the accumulation of positive charges in the terminal iodine atoms, thereby enhancing the bonding character of inter-slab I–I interactions across the organic barrier and activating out-of-plane contraction. Correlated charge transport, structural and photovoltaic measurements confirm that the onset of the light-induced contraction is synchronized to a threefold increase in carrier mobility and conductivity, which is consistent with an increase in the electronic band dispersion predicted by first-principles calculations. Flux-dependent space-charge-limited current measurement reveals that light-induced interlayer contraction activates interlayer charge transport. Lastly, the enhanced charge transport boosts the photovoltaic efficiency of two-dimensional perovskite solar cells up to 18.3% by increasing the device’s fill factor and open-circuit voltage.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Training Restricted Boltzmann Machines With a D-Wave Quantum Annealer

Restricted Boltzmann Machine (RBM) is an energy-based, undirected graphical model. It is commonly used for unsupervised and supervised machine learning. Typically, RBM is trained using contrastive divergence (CD). However, training with CD is slow and does not estimate the exact gradient of the log-likelihood cost function. In this work, the model expectation of gradient learning for RBM has been calculated using a quantum annealer (D-Wave 2000Q), where obtaining samples is faster than Markov chain Monte Carlo (MCMC) used in CD. Training and classification results of RBM trained using quantum annealing are compared with the CD-based method. The performance of the two approaches is compared with respect to the classification accuracies, image reconstruction, and log-likelihood results. The classification accuracy results indicate comparable performances of the two methods. Image reconstruction and log-likelihood results show improved performance of the CD-based method. It is shown that the samples obtained from quantum annealer can be used to train an RBM on a 64-bit “bars and stripes” dataset with classification performance similar to an RBM trained with CD. Though training based on CD showed improved learning performance, training using a quantum annealer could be useful as it eliminates computationally expensive MCMC steps of CD.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Dark Lock-in Thermography Identifies Solder Bond Failure as the Root Cause of Series Resistance Increase in Fielded Solar Modules

Correlating the electrical performance of photovoltaic modules to the spatially resolved photoluminescence, electroluminescence, and dark lock-in thermography (DLIT) images is an important long-term goal for developing solar cell technology. These images offer highly sophisticated and detailed information about the spatial distribution and (if imaged at successive time intervals) temporal degradation of local series and shunt resistances. There have been extensive studies to correlate these imaging techniques to local characteristics at the cell level. However, it has been difficult to extract and quantify module-level information from the techniques. In this study, we interpret module current-voltage (I-V) measurements along with corresponding DLIT images within a module-scale simulation framework, demonstrating that series resistance degradation of the module I-V characteristics, in this case, can be attributed to solder bond failures. Our simulations highlight how current crowding associated with a failed solder joint (or a section of the solder pad) translates to the characteristic point-like (asymmetric doublet) heating pattern in neighboring solder joints (or the neighboring regions of the solder pad). Overall, the correlation between series resistance and solder joint degradation could inform expedited diagnosis of field degradation of solar modules.

42 ENGINEERING↗
DOE OSTI2020

LCOE*: Re-Thinking LCOE for Photovoltaic Systems

Solar industry is working towards reducing the levelized cost of energy (LCOE). The LCOE formulation includes various implicitly connected cost and physical design parameters. This entails complex cost analyses by economists, and electrical analysis and energy yield calculations of solar farms by device physicists/technologists. The standard formulation requires a constant exchange of information to optimize the design of a specific farm. In this paper, we present a fundamental reformulation of LCOE (in terms of LCOE*) to deconvolve the cost vs. energy yield analysis so that economists and technologists can work independently towards minimizing LCOE. We validate our LCOE* formulation by comparing LCOE calculated by the traditional vs. new method. We further provide a global analysis of LCOE* as an illustrative example. This LCOE* will accelerate new technology development (e.g. bifacial PV) by allowing a rapid and transparent analysis of its cost-performance trade-off.

14 SOLAR ENERGY↗