Alessandro Geist | Search NASA

NASA NTRS2020

NASA SpaceCube Intelligent Multi-Purpose System for Enabling Remote Sensing, Communication, and Navigation in Mission Architectures

New, innovative CubeSat mission concepts demand modern capabilities such as artificial intelligence and autonomy, constellation coordination, fault mitigation, and robotic servicing –all of which require vastly more processing resources than legacy systems are capable of providing. Enabling these domains within a scalable, configurable processing architecture is advantageous because it also allows for the flexibility to address varying mission roles, such as a command and data-handling system, a high-performance application processor extension, a guidance and navigation solution, or an instrument/sensor interface. This paper describes the NASA SpaceCube Intelligent Multi-Purpose System (IMPS), which allows mission developers to mix-and-match 1U (10 cm × 10 cm) CubeSat payloads configured for mission-specific needs. The central enabling component of the system architecture to address these concerns is the SpaceCube v3.0 Mini Processor. This single-board computer features the 20nm Xilinx Kintex UltraScale FPGA combined with a radiation-hardened FPGA monitor, and extensive IO to integrate and interconnect varying cards within the system. To unify the re-usable designs within this architecture, the CubeSat Card Standard was developed to guide design of 1U cards. This standard define spinout configurations, mechanical, and electrical specifications for 1U CubeSat cards, allowing the backplane and mechanical enclosure to be easily extended. NASA has developed several cards adhering to the standard (System-on-Chip, power card, etc.), which allows the flexibility to configure a payload from a common catalog of cards.

Advanced Avionics, Hybrid Processing, Data Process↗

NASA NTRS2012

SpaceCube Mini

This version of the SpaceCube will be a full-fledged, onboard space processing system capable of 2500+ MIPS, and featuring a number of plug-andplay gigabit and standard interfaces, all in a condensed 3x3x3 form factor [less than 10 watts and less than 3 lb (approximately equal to 1.4 kg)]. The main processing engine is the Xilinx SIRF radiation- hardened-by-design Virtex-5 FX-130T field-programmable gate array (FPGA). Even as the SpaceCube 2.0 version (currently under test) is being targeted as the platform of choice for a number of the upcoming Earth Science Decadal Survey missions, GSFC has been contacted by customers who wish to see a system that incorporates key features of the version 2.0 architecture in an even smaller form factor. In order to fulfill that need, the SpaceCube Mini is being designed, and will be a very compact and low-power system. A similar flight system with this combination of small size, low power, low cost, adaptability, and extremely high processing power does not otherwise exist, and the SpaceCube Mini will be of tremendous benefit to GSFC and its partners. The SpaceCube Mini will utilize space-grade components. The primary processing engine of the Mini is the Xilinx Virtex-5 SIRF FX-130T radiation-hardened-by-design FPGA for critical flight applications in high-radiation environments. The Mini can also be equipped with a commercial Xilinx Virtex-5 FPGA with integrated PowerPCs for a low-cost, high-power computing platform for use in the relatively radiation- benign LEOs (low-Earth orbits). In either case, this version of the Space-Cube will weigh less than 3 pounds (.1.4 kg), conform to the CubeSat form-factor (10x10x10 cm), and will be low power (less than 10 watts for typical applications). The SpaceCube Mini will have a radiation-hardened Aeroflex FPGA for configuring and scrubbing the Xilinx FPGA by utilizing the onboard FLASH memory to store the configuration files. The FLASH memory will also be used for storing algorithm and application code for the PowerPCs and the Xilinx FPGA. In addition, it will feature highspeed DDR SDRAM (double data rate synchronous dynamic random-access memory) to store the instructions and data of active applications. This version will also feature SATA-II and Gigabit Ethernet interfaces. Furthermore, there will also be general-purpose, multi-gigabit interfaces. In addition, the system will have dozens of transceivers that can support LVDS (low-voltage differential signaling), RS-422, or SpaceWire. The SpaceCube Mini includes an I/O card that can be customized to meet the needs of each mission. This version of the SpaceCube will be designed so that multiple Minis can be networked together using SpaceWire, Ethernet, or even a custom protocol. Scalability can be provided by networking multiple SpaceCube Minis together. Rigid-Flex technology is being targeted for the construction of the SpaceCube Mini, which will make the extremely compact and low-weight design feasible. The SpaceCube Mini is designed to fit in the compact CubeSat form factor, thus allowing deployment in a new class of missions that the previous SpaceCube versions were not suited for. At the time of this reporting, engineering units should be available in the summer 2012.

Michael Lin↗

NASA NTRSDate not supplied

SpaceCubE OVERVIEW and Use of COTS Parts in Space

This presentation provides an overview of the SpaceCube data processing technology and successful use of Commercial Off-the-Shelf (COTS) parts on 11 space missions/payloads.

COTS Parts, SpaceCube↗