Search NASA⌕ Search

Engineering topics

Alexahin, Y

Publications and source records attributed to Alexahin, Y.

High-Field Combined-Function Magnets for a 1.5 x 1.5 TeV Muon Collider Storage Ring

Designs and parameters of dipoles and combined-function quadrupoles for bending arc lattice of a 1.5x1.5 TeV muon collider with an average luminosity of 4x1034 cm{sup -2}s{sup -1} are presented. The magnets use the Nb{sub 3}Sn superconductor and provide the required gradients and fields with the appropriate operating margins and field quality. The magnet apertures accommodate tungsten liners to minimize the dynamic heat load in the superconducting coils.

43 PARTICLE ACCELERATORS↗

Design of Accumulator and Compressor Rings for the Project-X Based Proton Driver

A Muon Collider (MC) and a Neutrino Factory (NF) - which may be considered as a step towards a MC - both require a high-power ({approx}4 MW) proton driver providing short (<1 m r.m.s. length) bunches for muon production. However, the driver repetition rates required for these two machines are different: {approx}15 Hz for MC and {approx}60 Hz for NF. This difference suggests employing two separate rings: one for accumulation of the proton beam from the Project-X linac in a few (e.g. 4) long bunches, the other for bunch compression - one by one for NF or all at a time for MC with simultaneous delivery to the target. The lattice requirements for these two rings are different: the momentum compaction factor in the accumulator ring should be large (and possibly negative) to avoid the microwave instability, while the compressor ring can be nearly isochronous in order to limit the required RF voltage and reduce the dispersion contribution to the beam size. In the present report we consider ring lattice designs which achieve these goals.

43 PARTICLE ACCELERATORS↗

Effect of Beam-Beam Interactions on Stability of Coherent Oscillations in a Muon Collider

In order to achieve peak luminosity of a muon collider in the 10{sup 34}/cm{sup 2}/s range the number of muons per bunch should be of the order of a few units of 10{sup 12} rendering the beam-beam parameter as high as 0.1 per IP. Such strong beam-beam interaction can be a source of instability if the working point is chosen close to a coherent beam-beam resonance. On the other hand, the beam-beam tunespread can provide a mechanism of suppression of the beam-wall driven instabilities. In this report the coherent instabilities driven by beam-beam and beam-wall interactions are studied with the help of BBSS code for the case of 1.5 TeV c.o.m muon collider.

43 PARTICLE ACCELERATORS↗

Effect of Field Errors in Muon Collider IR Magnets on Beam Dynamics

In order to achieve peak luminosity of a Muon Collider (MC) in the 10{sup 35} cm{sup -2}s{sup -1} range very small values of beta-function at the interaction point (IP) are necessary ({beta}* {le} 1 cm) while the distance from IP to the first quadrupole can not be made shorter than {approx}6 m as dictated by the necessity of detector protection from backgrounds. In the result the beta-function at the final focus quadrupoles can reach 100 km making beam dynamics very sensitive to all kind of errors. In the present report we consider the effects on momentum acceptance and dynamic aperture of multipole field errors in the body of IR dipoles as well as of fringe-fields in both dipoles and quadrupoles in the ase of 1.5 TeV (c.o.m.) MC. Analysis shows these effects to be strong but correctable with dedicated multipole correctors.

43 PARTICLE ACCELERATORS↗

A 3 TeV Muon Collider Lattice Design

A new lattice for 3 TeV c.o.m. energy with {beta}* = 5mm was developed which follows the basic concept of the earlier 1.5 TeV design but uses quad triplets for the final focus in order to keep the maximum magnet strength and aperture close to those in 1.5 TeV case. Another difference is employment of combined-function magnets with the goal to lower heat deposition in magnet cold mass and to eliminate bending field free regions which produce 'hot spots' of neutrino radiation that can be an issue at higher energy. The proposed lattice is shown to satisfy the requirements on luminosity, dynamic aperture and momentum acceptance.

43 PARTICLE ACCELERATORS↗

Observation of Instabilities of Coherent Transverse Ocillations in the Fermilab Booster

The Fermilab Booster - built more than 40 years ago - operates well above the design proton beam intensity of 4 {center_dot} 10{sup 12} ppp. Still, the Fermilab neutrino experiments call for even higher intensity exceeding 5.5 {center_dot} 10{sup 12} ppp. A multitude of intensity related effects must be overcome in order to meet this goal including suppression of coherent dipole instabilities of transverse oscillations which manifest themselves as a sudden drop in the beam current. In this report we present the results of observation of these instabilities at different tune, coupling and chromaticity settings and discuss possible cures.

43 PARTICLE ACCELERATORS↗

Tune Determination of Strongly Coupled Betatron Oscillations in a Fast-Ramping Synchrotron

Tune identification -- i.e. attribution of the spectral peak to a particular normal de of oscillations -- can present a significant difficulty in the presence of strong transverse coupling when the normal mode with a lower damping rate dominates spectra of Turn-by-Turn oscillations in both planes. The introduced earlier phased sum algorithm helped to recover the weaker normal mode signal from the noise, but by itself proved to be insufficient for automatic peak identification in the case of close phase advance distribution in both planes. To resolve this difficulty we modified the algorithm by taking and analyzing Turn-by-Turn data for two different ramps with the beam oscillation excited in each plane in turn. Comparison of relative amplitudes of Fourier components allows for correct automatic tune identification. The proposed algorithm was implemented in the Fermilab Booster B38 console application and successfully used for tune, coupling and chromaticity measurements.

43 PARTICLE ACCELERATORS↗

An application for tunes and coupling evaluation from turn-by-turn data at the Fermilab Booster

A console application using the phasing of Turn-by-Turn signals from the different BPMs has been tested at the Fermilab Booster. This technique allows the on-line detection of the beam tunes during the fast Booster ramp in conditions where other algorithms were unsuccessful. The application has been recently expanded to include the computation of the linear coupling coefficients. Algorithm and measurement results are presented. Although improved by the phased sum technique the automatic identification of the tunes is not always successful. This makes the use of the on-line application difficult. Ideas for further improvements are under investigation. Measurements have indicated that the effect of the skew quadrupoles is by a factor 3 weaker than expected from the nominal optics. A calibration of the skew quadrupole circuits using the TBT data is planned.

43 PARTICLE ACCELERATORS↗

Chromaticity correction for a muon collider optics

Muon Collider (MC) is a promising candidate for the next energy frontier machine. However, in order to obtain peak luminosity in the 10{sup 34} cm{sup 2}s{sup -1} range the collider lattice designmust satisfy a number of stringent requirements. In particular the expected large momentum spread of the muon beam and the very small {beta}* call for a careful correction of the chromatic effects. Here we present a particular solution for the interaction region (IR) optics whose distinctive feature is a three-sextupole local chromatic correction scheme. The scheme may be applied to other future machines where chromatic effects are expected to be large. The expected large muon energy spread requires the optics to be stable over a wide range of momenta whereas the required luminosity calls for {beta}* in the mm range. To avoid luminosity degradation due to hour-glass effect, the bunch length must be comparatively small. To keep the needed RF voltage within feasible limits the momentum compaction factor must be small over the wide range of momenta. A low {beta}* means high sensitivity to alignment and field errors of the Interaction Region (IR) quadrupoles and large chromatic effects which limit the momentum range of optics stability and require strong correction sextupoles, which eventually limit the Dynamic Aperture (DA). Finally, the ring circumference should be as small as possible, luminosity being inversely proportional to the collider length. A promising solution for a 1.5 TeV center of mass energy MC with {beta}* = 1 m in both planes has been proposed. This {beta}* value has been chosen as a compromise between luminosity and feasibility based on the magnet design and energy deposition considerations. The proposed solution for the IR optics together with a new flexible momentum compaction arc cell design allows to satisfy all requirements and is relatively insensitive to the beam-beam effect.

43 PARTICLE ACCELERATORS↗

Muon Collider design status

Muon Collider (MC) - proposed by G.I. Budker and A.N. Skrinsky a few decades ago - is now considered as the most exciting option for the energy frontier machine in the post-LHC era. A national Muon Accelerator Program (MAP) is being formed in the USA with the ultimate goal of building a MC at the Fermilab site with c.o.m. energy in the range 1.5-3 TeV and luminosity of {approx} 1.5 {center_dot} 10{sup 34} cm{sup -2} s{sup -1}. As the first step on the way to MC it envisages construction of a Neutrino Factory (NF) for high-precision neutrino experiments. The baseline scheme of the NF-MC complex is presented and possible options for its main components are discussed.

43 PARTICLE ACCELERATORS↗

Tune Evaluation From Phased BPM Turn-By-Turn Data

In fast ramping synchrotrons like the Fermilab Booster the conventional methods of betatron tune evaluation from the turn-by-turn data may not work due to rapid changes of the tunes (sometimes in a course of a few dozens of turns) and a high level of noise. We propose a technique based on phasing of signals from a large number of BPMs which significantly increases the signal to noise ratio. Implementation of the method in the Fermilab Booster control system is described and some measurement results are presented.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Rapid-cycling synchrotron with variable momentum compaction

There are conflicting requirements on the value of the momentum compaction factor during energy ramping in a synchrotron: at low energies it should be positive and sufficiently large to make the slippage factor small so that it is possible to work closer to the RF voltage crest and ensure sufficient RF bucket area, whereas at higher energies it should be small or negative to avoid transition crossing. In the present report we propose a lattice with a variable momentum compaction factor and consider the possibility of using it in a high repetition rate proton driver for a muon collider and neutrino factory.

43 PARTICLE ACCELERATORS↗

Conceptual design of the muon collider ring lattice

Muon collider is a promising candidate for the next energy frontier machine. However, in order to obtain peak luminosity in the 10{sup 35}/cm{sup 2}/s range the collider lattice design must satisfy a number of stringent requirements, such as low beta at IP ({beta}* < 1 cm), large momentum acceptance and dynamic aperture and small value of the momentum compaction factor. Here we present a particular solution for the interaction region optics whose distinctive feature is a three-sextupole local chromatic correction scheme. Together with a new flexible momentum compaction arc cell design this scheme allows to satisfy all the above-mentioned requirements and is relatively insensitive to the beam-beam effect.

43 PARTICLE ACCELERATORS↗

Helical FOFO Snake for 6D Ionization Cooling of Muons

A channel for 6D ionization cooling of muons is described which consists of periodically inclined solenoids of alternating polarity, liquid hydrogen absorbers placed inside the solenoids and RF cavities between them. An important feature of such a channel (called Helical FOFO snake) is that it can cool simultaneously muons of both signs. Theoretical considerations as well as results of simulations with G4beamline are presented which show that a 200 MHz HFOFO snake has sufficient acceptance to be used for initial 6D cooling in muon colliders and neutrino factories.

43 PARTICLE ACCELERATORS↗

Helical FOFO snake for 6D ionization cooling of muons

A channel for 6D ionization cooling of muons is described which consists of periodically inclined solenoids of alternating polarity, liquid hydrogen absorbers placed inside solenoids and RF cavities between them. Important feature of such channel (called Helical FOFO snake) is that it can cool simultaneously muons of both signs. Theoretical considerations as well as results of simulations with G4Beamline are presented which show that 200MHz HFOFO snake has sufficient acceptance to be used for initial 6D cooling in muon colliders and neutrino factories.

43 PARTICLE ACCELERATORS↗

Circularly Inclined Solenoid Channel for 6D Ionization Cooling of Muons

Ionization cooling is essential for realization of Muon Collider, muons beam based neutrino factories and other experiments involving muons. The simplest structure - absorber(s) immersed in alternating solenoidal magnetic field - provides only transverse cooling since the longitudinal motion in the most suitable momentum range (2-300MeV/c) is naturally anti-damped. To overcome this difficulty it is proposed to periodically tilt solenoids so that a rotating transverse magnetic field was created. By choosing the phase advance per period above a multiple of 2{pi} it is possible to ensure that muons with higher momentum make a longer path in the absorber (whether distributed or localized) thus providing longitudinal damping. Basic theory of such channel and results of tracking simulations are presented.

43 PARTICLE ACCELERATORS↗