Engineering topics

Alfonso, N.

Publications and source records attributed to Alfonso, N..

10 records

DOE OSTI2024

Thermonuclear performance variability near ignition at the National Ignition Facility

We describe our current understanding of the variability and degradation mechanisms observed through a series of five indirectly driven inertial fusion implosions fielded at the National Ignition Facility in the fall of 2021, four of which attempted to reproduce the first experiment to achieve Lawson's criterion for ignition with a thermonuclear yield of 1.35 MJ on August 8, 2021. A large number of absolutely calibrated (imaging, time-resolved, and spectrally resolved) x-ray and neutron diagnostics are fielded on the NIF along multiple lines of sight for each experiment. This allows for a reconstruction of the DT fuel and ablator mix injected into the hotspot around peak burn. We show that nuclear yield variations are well reproduced by numerical modeling when the measured low mode asymmetries and mix mass are included. Furthermore, these observed perturbations during burn are linked to small variations in laser delivery and capsule defects. Stringent specifications are then set to achieve robust ignition with the implosion design studied in this paper.

Divol, L. (ORCID:0000000269699898)↗

DOE OSTI2024

Achievement of Target Gain Larger than Unity in an Inertial Fusion Experiment

On December 5, 2022, an indirect drive fusion implosion on the National Ignition Facility (NIF) achieved a target gain G target of 1.5. This is the first laboratory demonstration of exceeding “scientific breakeven” (or G target > 1 ) where 2.05 MJ of 351 nm laser light produced 3.1 MJ of total fusion yield, a result which significantly exceeds the Lawson criterion for fusion ignition as reported in a previous NIF implosion [H. Abu-Shawareb (Indirect Drive ICF Collaboration), ]. This achievement is the culmination of more than five decades of research and gives proof that laboratory fusion, based on fundamental physics principles, is possible. This Letter reports on the target, laser, design, and experimental advancements that led to this result. Published by the American Physical Society 2024

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Proof-of-Principle Experiment on the Dynamic Shell Formation for Inertial Confinement Fusion

In the dynamic-shell (DS) concept [Goncharov et al., Phys Rev. Lett. 125, 065001 (2020)] for laser-driven inertial confinement fusion the deuterium-tritium fuel is initially in the form of a homogeneous liquid inside a wetted-foam spherical shell. This fuel is ignited using a conventional implosion, which is preceded by a initial compression of the fuel followed by its expansion and dynamic formation of a high-density fuel shell with a low-density interior. This letter reports on a scaled-down, proof-of-principle experiment on the OMEGA laser demonstrating, for the first time, the feasibility of DS formation. A shell is formed by convergent shocks launched by laser pulses at the edge of a plasma sphere, with the plasma itself formed as a result of laser-driven compression and relaxation of a surrogate plastic-foam ball target. Three x-ray diagnostics, namely, 1-D spatially resolved self-emission streaked imaging, 2-D self-emission framed imaging, and backlighting radiography, have shown good agreement with the predicted evolution of the DS and its stability to low Legendre mode perturbations introduced by laser irradiation and target asymmetries.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Lawson Criterion for Ignition Exceeded in an Inertial Fusion Experiment

For more than half a century, researchers around the world have been engaged in attempts to achieve fusion ignition as a proof of principle of various fusion concepts. Following the Lawson criterion, an ignited plasma is one where the fusion heating power is high enough to overcome all the physical processes that cool the fusion plasma, creating a positive thermodynamic feedback loop with rapidly increasing temperature. In inertially confined fusion, ignition is a state where the fusion plasma can begin “burn propagation” into surrounding cold fuel, enabling the possibility of high energy gain. While “scientific breakeven” (i.e., unity target gain) has not yet been achieved (here target gain is 0.72, 1.37 MJ of fusion for 1.92 MJ of laser energy), this work reports the first controlled fusion experiment, using laser indirect drive, on the National Ignition Facility to produce capsule gain (here 5.8) and reach ignition by nine different formulations of the Lawson criterion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Foam-lined hohlraum, inertial confinement fusion experiments on the National Ignition Facility

Experiments on the National Ignition Facility (NIF) to study hohlraums lined with a 20-mg/cc 400-μm-thick Ta 2 O 5 aerogel at full scale (hohlraum diameter = 6.72 mm) are reported. Driven with a 1.6-MJ, 450-TW laser pulse, the performance of the foam liner is diagnosed using implosion hot-spot symmetry measurements of the high-density carbon (HDC) capsule and measurement of inner beam propagation through a thin-wall 8-μm Au window in the hohlraum. Results show an improved capsule performance due to laser energy deposition further inside the hohlraum, leading to a modest increase in x-ray drive and reduced preheat due to changes in the x-ray spectrum when the foam liner is included. In addition, the outer cone bubble uniformity is improved, but the predicted improvement in inner beam propagation to improve symmetry control is not realized for this foam thickness and density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Fill tube dynamics in inertial confinement fusion implosions with high density carbon ablators

Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Experimental demonstration of the reduced expansion of a laser-heated surface using a low density foam layer, pertaining to advanced hohlraum designs with less wall-motion

The ablative expansion of laser-heated materials is important for determining how hohlraum cavities can be utilized for inertial confinement fusion. The utility of a low-density foam layer to reduce the density of the expanding heated hohlraum wall is demonstrated here in a series of experiments on the National Ignition Facility. X-ray radiography measurements of the expanding foam-lined Au wall in low aspect-ratio cylindrical geometry are used to compare the impact of Au-doped CH and Ta 2 O 5 foams between 10 and 40 mg/cc on the wall expansion. HYDRA Simulations are used to estimate the x-ray transmission at the 1/4 nc surface, which is important in understanding the absorption of laser light by the plasma. These demonstrate for the first time that a foam layer reduces the expansion of a hohlraum-like target and illustrate that the interplay between the expanding foam plasma and the shock reflected by the hohlraum wall is critical in optimizing foam-liner parameters to achieve the maximum time for a symmetric drive on a capsule.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Recent and planned hydrodynamic instability experiments on indirect-drive implosions on the National Ignition Facility

At National Ignition Facility (NIF), yield amplification due to alpha particle heating approached ~3 in the highest performing inertial confinement fusion (ICF) implosions, while yield amplification of ~15-30 is needed for ignition. Hydrodynamic instabilities are a major factor in degradation of implosions while understanding and mitigation of the instabilities are critical to achieving ignition. This article describes recent and planned hydrodynamic instability experiments with several focused platforms that have been developed to directly measure these instabilities in all phases of ICF implosions. Measurements of ripple-shock generation at OMEGA laser have indicated initial seeds for the instabilities in three ablators - plastic (CH), beryllium, and high-density carbon (HDC). Hydrodynamic Growth Radiography (HGR) platform was used to measure instability growth at the ablation front in the acceleration phase of implosions. This platform used pre-imposed 2-D perturbations for growth factor measurements at different perturbation wavelengths and was also used to measure growth of “native roughness” modulations, fill tubes, and capsule support membranes or “tents”. Also, in the acceleration phase several new experimental platforms have been or are being developed to measure instability growth at the ablator-ice interface. In the deceleration phase of implosions, “self-emission” and “self-backlighting” platforms were developed to measure perturbations near peak compression. This article reviews recent progress and results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Ultra-high aspect ratio pores milled in diamond via laser, ion and electron beam mediated processes

Microfabrication techniques are critical for the rapid prototyping and development of applications for cutting edge materials. Recently diamond has gained considerable interest for quantum photonic, biosensing, inertial confinement fusion and magnetometer applications. In this article, ultra-high aspect ratio milling of diamond micropores by photon, ion and electron based methods is reported. A multiphoton absorption laser ablation approach is revealed to rapidly produce sub-10 μm diameter micropores in diamond with an aspect ratio of 14:1 and a tapered profile at the surface interface. Chemically active, oxygen focused ion beam milling produces high-aspect ratio pores in diamond with an aspect ratio of 65:1 and minimal tapering over the length of the pore, overcoming the physical interaction volume limitations imposed in conventional gallium based focused ion beam milling and laser ablation methods. Oxygen-mediated electron beam induced etching is revealed to negate the limitations imposed by physical sputtering mechanisms utilized in focused ion beam milling via the direct initiation of chemical reactions at the receding surface, producing aspect ratios on the order of 200:1. Numerical simulations reveal the physical basis for the superior aspect-ratio pore milling of the oxygen focused ion beam milling and electron beam induced etching methods. Our results demonstrate direct-write methods for the fabrication of ultra-high aspect micropores in diamond and provide insight into the underlying mechanisms of these physical processes. The three methods demonstrated here can be interchanged for applications based on the desired characteristic aspect ratio and process throughput.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Mixing in ICF implosions on the National Ignition Facility caused by the fill-tube

The micrometer-scale tube that fills capsules with thermonuclear fuel in inertial confinement fusion experiments at the National Ignition Facility is also one of the implosion's main degradation sources. It seeds a perturbation that injects the ablator material into the center, radiating away some of the hot-spot energy. This paper discusses how the perturbation arises in experiments using high-density carbon ablators and how the ablator mix interacts once it enters the hot-spot. Both modeling and experiments show an in-flight areal-density perturbation and localized x-ray emission at stagnation from the fill-tube. Simulations suggest that the fill-tube is degrading an otherwise 1D implosion by ~2×, but when other degradation sources are present, the yield reduction is closer to 20%. Characteristics of the fill-tube assembly, such as the through-hole size and the glue mass, alter the dynamics and magnitude of the degradation. Overall, these aspects point the way toward improvements in the design, some of which (smaller diameter fill-tube) have already shown improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗