Search NASA⌕ Search

Engineering topics

Alia, Shaun M.

Publications and source records attributed to Alia, Shaun M..

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Identifying electrochemical processes by distribution of relaxation times in proton exchange membrane electrolyzers

Distribution of relaxation time (DRT) is used to interpret electrochemical impedance spectroscopy (EIS) for proton exchange membrane (PEM) water electrolyzers, with an attempt to separate overlapped relaxation processes in Nyquist plots. By varying operating conditions and catalyst loadings, four main relaxation peaks arising from EIS can be identified and successfully separated from low to high frequencies as (P1) mass transport, (P2) oxygen evolution reaction kinetics, (P3) reaction kinetics (with faster time constant than P2), and (P4) ionic transport. Here, the shape, height, and frequency of the DRT peaks change with different membrane electrode assembly (MEA) configurations. Electron microscopy reveals distinct features from the cross-sectioned MEAs which verify critical DRT results in that increasing the iridium (Ir)-anode loading from 0.2 mgIr/cm 2 to 1.5 mgIr/cm 2 reduces kinetic losses due to higher site-access; a thick and compacted anode, however, also triggers higher ohmic resistances from membrane/catalyst layer hydration and increases transport losses due to longer ionomer pathways. DRT provides higher resolution to EIS for deconvoluting processes with different relaxation times and the quantification of DRT peaks improves the accounting of total losses from each process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Simulated Start-Stop and the Impact of Catalyst Layer Redox on Degradation and Performance Loss in Low-Temperature Electrolysis

Stress tests are developed that focus on anode catalyst layer degradation in proton exchange membrane electrolysis due to simulated start-stop operation. Ex situ testing indicates that repeated redox cycling accelerates catalyst dissolution, due to near-surface reduction and the higher dissolution kinetics of metals when cycling to high potentials. Similar results occur in situ, where a large decrease in cell kinetics (>70%) is found along with iridium migrating from the anode catalyst layer into the membrane. Additional processes are observed, however, including changes in iridium oxidation, the formation of thinner and denser catalyst layers, and platinum migration from the transport layer. Increased interfacial weakening is also found, adding to both ohmic and kinetic loss by adding contact resistances and isolating portions of the catalyst layer. Repeated shutoffs of the water flow further accelerate performance loss and increase the frequency of tearing and delamination at interfaces and within catalyst layers. These tests were applied to several commercial catalysts, where higher loss rates were observed for catalysts that contained ruthenium or high metal content. These results demonstrate the need to understand how operational stops occur, to identify how loss mechanisms are accelerated, and to develop strategies to limit performance loss.

08 HYDROGEN↗
DOE OSTI2024

Catalyst-Specific Accelerated Stress Tests in Proton Exchange Membrane Low-Temperature Electrolysis for Intermittent Operation

Device-level stress tests are developed that focus on anode catalyst layer degradation and future anticipated operating conditions, including intermittent load and reduced platinum group metal content. Square-wave cycles with an upper load limit of 2.5 A cm -2 are utilized to screen commercial iridium (Ir) materials. Performance losses are primarily due to decreasing kinetics and are accompanied by catalyst migration into the membrane, worsening catalyst/ionomer integration, and weakening of the catalyst/membrane interface. For ruthenium-containing catalysts, the in situ performances are higher but durabilities lower than Ir baselines, and any performance advantage is lost within the test. Increased loss is likely due to the higher dissolution rate; microscopy confirmed greater degrees of ruthenium migration. For Ir metal or mixed oxides, ex situ activity improvements generally did not translate to in situ performance. The durability, however, is significantly lower and the loss rate increased from 3 (oxide) to 9 (metal) μ V cycle -1 . These results are consistent with historical findings in literature, rationalize the continued use of iridium oxide as a baseline catalyst, and demonstrate that traditional catalyst development approaches may not improve device-level durability when focused on low-cost applications. A shift in focus may therefore be more effective at improving catalyst utilization and lessening load requirements.

08 HYDROGEN↗
DOE OSTI2024

Aerogel-derived nickel-iron oxide catalysts for oxygen evolution reaction in alkaline media

Anion exchange membrane water electrolyzers (AEMWEs) can generate hydrogen with a pure water feed using noble metal-free catalysts. Here, the development of highly active and stable catalysts for oxygen evolution reaction (OER) is required for improving performance of AEMWEs systems. Ni-Fe (oxy)hydroxides show high OER catalytic activity in alkaline media, but typically have low surface area. In this work, we investigate a series of Ni-Fe oxides with high surface area and disordered morphology, obtained using an aerogel synthesis method. We evaluate the impact of different synthesis variables on the OER activity and demonstrate that heat treatment at high temperatures generates more ordered structure, resulting in a decrease in OER activity. Advanced characterization reveals that maintaining highly disordered and porous structure of the aerogel is essential to achieving high OER activity, as it enables the formation of highly OER-active lamellar structures of the catalyst.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Catalytic Activity and Stability of Non-Platinum Group Metal Oxides for the Oxygen Evolution Reaction in Anion Exchange Membrane Electrolyzers

The activities and stabilities of non-platinum group metals (PGMs) in the forms of monometallic (Mn 2 O 3 , Fe 2 O 3 , Co 3 O 4 , NiO) and bimetallic (NiFe 2 O 4 , CoNiO 2 ) oxides were assessed for the oxygen evolution reaction (OER) in alkaline media and compared with IrO 2 . Both half-cell, rotating disc electrode (RDE) apparatus and single-cell, membrane electrode assemblies (MEA) were used to study kinetic and device-level performance in parallel and to provide insights into the use of these materials in anion exchange membrane (AEM) electrolyzers. Normalization of RDE results by geometric and physical surface areas, double layer capacitance, and metal content probed differences in physically vs electrochemically accessible surface areas and ensured reported trends were independent of the normalization method. The results showed that: (i) Ni- and Co- containing materials met or exceeded IrO 2 performance in both RDE and MEA testing, (ii) Co 3 O 4 deactivated over time-on-stream (1.8 V for 13.5 h) due to oxide and, relatedly, particle growth, (iii) NiFe 2 O 4 increased in activity over time-on-stream due to dissolution of Fe and an increased Ni/Fe ratio, and (iv) reduction of catalyst layer resistance is an avenue to further increase device-level performance. These results demonstrated the clear viability for non-PGMs to be used as anode catalysts in AEM devices.

25 ENERGY STORAGE↗
DOE OSTI2022

Rotating Disk Electrode Standardization and Best Practices in Acidic Oxygen Evolution for Low-Temperature Electrolysis

Efforts in oxygen evolution catalyst development have significantly increased and often use rotating disk electrode half-cells to evaluate intrinsic kinetics and screen materials for short-term durability. Standardizing rotating disk electrode test protocols is critical to experimental accuracy, to realistically assess their potential impact at a device level and to assess how different catalyst approaches and concepts are prioritized. The goal of this study is to provide standardized test protocols and suggest best practices to help reduce variability in ex situ materials characterization in the broader community. Specifically, these protocols focus on test cleanliness and materials choices, including how electrodes are prepared and tested, and the impact on activity observations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electrolyzer Performance Loss from Accelerated Stress Tests and Corresponding Changes to Catalyst Layers and Interfaces

Stress tests are developed for proton exchange membrane electrolyzers that utilize low catalyst loading, elevated potential, and frequent cycling with square- and triangle-waves to accelerate anode catalyst layer degradation during intermittent operation. Kinetics drive performance losses (ohmic/transport secondary) and are accompanied by decreasing exchange current density, decreasing cyclic voltammetric capacitance, and increasing polarization resistance. Decreased kinetics are likely due to a combination of iridium (Ir) migration into electrochemically inaccessible locations in the anode or membrane, Ir particle growth (supported by X-ray scattering), changes in the extent of the Ir oxidation state (supported by X-ray absorption spectroscopy), and anode catalyst layer reordering. Decreasing catalyst/transport layer contact and catalyst/membrane interfacial tearing may add contact resistances and account for increasing ohmic losses. Performance losses for low and moderate catalyst loading, as well as from accelerated and model wind/solar cycling protocols, were likewise dominated by kinetics but vary in severity. Additionally, accelerated cycling (1 cycle per minute) appears to reasonably accelerate relevant loss mechanisms and can be used to project electrolyzer lifetime from anode deterioration. Ongoing accelerated stress test development and studies into performance loss mechanisms will continue to be critical as electrolysis shifts to intermittent power and low-cost applications.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Optimization of Extended-Surface PtNi Nanowire Oxygen Reduction Electrocatalysts Produced via Atomic Layer Deposition

Polymer electrolyte membrane fuel cells (PEMFCs) produce electricity with only heat and water as byproducts, but sluggish kinetics of the oxygen reduction reaction (ORR) at the cathode and durability limitations restrict widespread commercialization, motivating the development of advanced catalysts. In this research, extended-surface platinum nickel (PtNi) nanowires (NWs) synthesized using the scalable atomic layer deposition (ALD) technique are investigated with the goal of exploring the durability benefits of high-aspect-ratio electrocatalysts and the tunability of beneficial kinetic properties. The surface and bulk composition and the structure of the PtNi NWs were investigated as a function of a series of postsynthesis modifications. The results from a combination of electron microscopy and X-ray spectroscopy characterization techniques were correlated to electrochemical performance to gain a comprehensive understanding of the structure-property-performance relationships. The robust structure of the ALD-derived NWs enabled additional postsynthesis optimization steps, which were not possible with previous-generation materials synthesized via spontaneous galvanic displacement, resulting in a catalyst with beneficial properties for catalyst kinetics as well as improved durability. Our study demonstrates potential pathways toward further improving the performance of this class of materials through optimization of bulk and surface properties of the catalyst.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Discovering and Demonstrating a Novel High-Performing 2D-Patterned Electrode for Proton-Exchange Membrane Water Electrolysis Devices

Proton-exchange membrane water electrolysis (PEMWE) produces hydrogen with high efficiency and purity but uses high-loading platinum-group metal (PGM) catalysts. Such concerns call for the development of novel electrode architectures to improve catalyst utilization and mass activity, thus promoting PEMWE cost competitiveness for large-scale implementation. In this study, we demonstrated, for the first time, a novel two-dimensional (2D)-patterned electrode with edge effects to address these challenges. The edge effect was induced by membrane properties, potential distribution, and counter electrode coverage and could be optimized by tuning the catalyst layer dimensions. To achieve identical PEMWE performance, the optimal pattern saved the 21% anode PGM catalyst compared with the conventional catalyst fully covered electrode. The PGM catalyst could be further reduced by 61% to boost mass activity with no significant performance loss. The results also indicated that the electrode uniformity in PEMWE cells might not be as critical as that in PEM fuel cells. Finally, the novel 2D-patterned electrode could effectively reduce PGM catalyst loading, accelerating affordable and large-scale production of hydrogen and other value-added chemicals via electrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Mechanistic understanding of pH effects on the oxygen evolution reaction

The oxygen-evolution reaction (OER) is pivotal in many energy-conversion technologies as it is an important counter reaction to others that convert stable chemicals to higher-value products using electrochemistry. The local microenvironment and pH for the anode OER can vary from acidic to neutral to alkaline depending on the system being explored, making definitive mechanistic insights difficult. In this paper, we couple experiments, first-principles calculations based on density functional theory, microkinetics, and transport modeling to explore the entire pH range of the OER. At low current densities, neutral pH values unexpectedly perform better than the acidic and alkaline conditions, and this trend is reversed at higher current densities (> 20 mA cm -2 ). Using multiscale modeling, this switch is rationalized by a change from a dual-reaction mechanism to a single rate-determining step. The model also shows how the alkaline reaction rates dominate in the middle to high pH range. Furthermore, we explore that the local pH for near-neutral conditions is much different (e.g., 2.4 at the reaction surface vs. 9 in the bulk) than the pH extremes, demonstrating the criticality that transport phenomena plays in kinetic activity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Effect of Material Properties on Oxygen Evolution Activity and Assessing Half-Cell Screening as a Predictive Tool in Electrolysis

Iridium-based oxygen evolution catalysts are screened in this study for activity and stability with rotating disk electrode (RDE) half-cells. This study focuses on the electrochemical and materials approaches needed to characterize oxygen evolution catalysts, and include testing for activity, stability, composition, oxide content, and structure. Findings also discuss recommendations for data interpretation and detail the difficulties of comparing catalysts across materials sets with different elemental and oxide compositions, and linking RDE activity to device-level performance. The materials evaluated are a mixture of oxides and metals, and several methods are used to quantify metal content, qualitatively assess oxide content, and determine total surface area. Oxygen evolution activities and stabilities are compared, where a wide range of results are reported. In general, higher RDE performances are found for catalysts that contained larger amounts of ruthenium and metals. Higher durability, however, is found for catalysts that only contained iridium and a higher proportion of oxides. Additionally, catalysts are evaluated for performance in membrane electrode assemblies to assess RDE as a predictive tool in electrolysis. While activity trends within individual material sets generally held between ex- and in-situ testing, RDE tends to overestimate the activity of more metallic catalysts when compared to device-level performance. These results stress the need for multiple metal/oxide baselines for mixed catalysts, to better project in-situ kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Current research in low temperature proton exchange membrane-based electrolysis and a necessary shift in focus

While hydrogen has limited use in energy markets today, significant growth is possible in grid storage and as an energy carrier in other sectors. Along with lower electricity prices, further hydrogen cost reduction can enable electrochemical water splitting, particularly as the use of intermittent, renewable power sources increases and the quantity and duration of storage requirements limit electrical storage options. With the improved viability of large-scale hydrogen production, research in low temperature electrolysis has dramatically increased. The overwhelming majority of research efforts within proton exchange membrane-based systems has focused on catalyst development, although a smaller set have developed transport layers as well. As proton exchange membrane-based electrolysis shifts into higher technology readiness levels, however, there is a growing need for work optimizing materials integration, developing component-specific and device-level accelerated stress tests, and addressing manufacturing considerations. These areas directly impact electrolyzer performance, durability, and cost, and are critical to advancing hydrogen’s value and electrochemical water splitting.

08 HYDROGEN↗