Search NASA⌕ Search

Engineering topics

Allard, Lawrence F.

Publications and source records attributed to Allard, Lawrence F..

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

An additively manufactured near-eutectic Al-Ce-Ni-Mn-Zr alloy with high creep resistance

A new additively manufactured (AM) Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt.%) near-eutectic alloy is reported, which shows unprecedented creep resistance up to 400 °C (a homologous temperature of 0.72). The eutectic solidification microstructure comprises ~ 27 vol% of coarsening-resistant second phase network with an ultrafine (<100 nm) inter-phase spacing. Both Mn and Zr contribute to creep resistance of the alloy. Small amount of Mn addition promotes selection of coarsening resistant phases without compromising the alloy processability. Zr not only improves hot-tearing resistance, but further enhances the second phase coarsening resistance resulting in improved creep resistance. Neutron diffraction performed during creep deformation reveals that the underlying mechanism for creep resistance in this alloy is impedance to dislocation motion stemming from the ultrafine eutectic solidification microstructure, whereas load transfer strengthening becomes less effective as the creep temperature increases. The second phase forms a continuous network in the as-fabricated condition, which is maintained during long-term creep at 300 °C. However, this network is fragmented into fine dispersoids at higher temperatures. It is proposed that the rate-limiting deformation mechanism at 300–400 °C is (i) dislocation climb for the alloy with fragmented second phase dispersoids and (ii) Orowan looping for the alloy with a continuous second phase network. In conclusion, the present design of an AM-processable multicomponent eutectic alloy with high creep resistance can be applied to other metallic systems exhibiting eutectic reactions, with expected extreme creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and strengthening of Al-6Ce-3Ni-0.7Fe (wt%) alloy manufactured by laser powder-bed fusion

In this study, an Al-6Ce-3Ni-0.7Fe (wt%) alloy was fabricated via laser powder-bed fusion and its microstructure, thermal stability, tensile properties, and creep properties are investigated for two rapid-solidification rates with different eutectic spacings. For both faster- and slower-cooled states, the as-fabricated alloy mostly shows elongated grains with very fine eutectic networks (~40 nm lamellar width) comprising a high-volume fraction (~18 %) of intermetallic phases. Faster-cooled samples, however, display a less continuous eutectic network with finer spacing (~100 nm), leading to higher Orowan strengthening and therefore superior microhardness and yield stress up to ~350 °C. Upon aging (300 - 450 °C), micron-size Al 9 (Ni,Fe) 2 needle-like precipitates form within grains, and the Al 11 Ce 3 eutectic network spheroidizes, while retaining a submicron width and spacing, resulting in 33–37 % drop in microhardness after 144 h aging at 400 °C. Limited tensile ductility (~6 %) and creep ductility (~1-2 %) are measured for both faster- and slower-cooled alloys due to an inhomogeneous microstructure, where cavitation preferentially initiates at melt-pool boundaries, precipitate-free zones, and/or denuded zones, eventually leading to local fracture. Denuded zones, induced by stress, form due to diffusional flow with stress-dependent orientations, and are identified as microstructurally weak regions leading to strain localization. The present alloy does not show a significant difference in 300 °C creep resistance between: (i) tensile and compressive loading, (ii) faster- and slower-cooled samples, and (iii) continuous and spheroidized eutectics. Creep resistance at 300 °C is comparable to that of a Ce-richer Al-10.5Ce-3.1Ni-1.2Mn (wt%) alloy, despite the formation of denuded zones and needle-like Al 9 (Ni,Fe) 2 precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Investigation of Cu Species in Dealuminated Beta Zeolite Studied by Operando Closed-Cell Gas Reaction STEM

Direct conversion of ethanol to C3+ olefins is an attractive pathway to produce sustainable aviation fuels [1]. We recently reported a copper-containing catalyst supported on dealuminated (DeAl) beta zeolite that is capable of catalyzing cascade ethanol to olefins reactions with high olefins selectivity (88% C3+ olefin selectivity at 100% ethanol conversion). However, one of the deactivation mechanisms of the catalyst is copper sintering [2]. It was found that copper agglomerates can be redispersed through a simple oxidative treatment. To better understand the kinetics and process conditions conducive to redispersion, we studied the atmosphere and temperature dependent Cu species in Cu/DeAl-Beta catalyst under conditions matching those of the working catalyst.

beta zeolite↗
DOE OSTI2023

Effect of Mn on eutectic phase equilibria in Al-rich Al-Ce-Ni alloys

Microstructural analysis of additively manufactured (AM) Al-Ce-Ni-Mn alloys has identified phases not predicted from existing ternary liquidus projections in the Al-Ce-Ni system. Because the rapid cooling rate of AM is orders of magnitude above that of traditional casting, it is unclear if these additional phases arose from the non-equilibrium processing conditions of AM, a drastic shift in phase stability in the system due to the addition of 1 wt% Mn, or some combination of these two influences. The phases and microstructure of cast samples of Al-Ce-Ni and Al-Ce-Ni-Mn alloys were characterized for several annealing conditions which revealed the equilibrium phases at different temperatures. Phase analysis confirmed that minute levels of Mn substituted for Ni in the system drastically shifts the liquidus projection in the Al-rich corner of the ternary phase diagram such that the eutectic Al 3 Ni phase is suppressed in favor of the Al 23 Ni 6 (Ce,Mn) 4 phase. Further addition of Mn promotes the formation of Al 20 Mn 2 Ce and Al 10 Mn 2 Ce phases. The phase analysis data was then used to improve the CALPHAD modeling of the liquidus projection and isothermal sections for the Al-rich Al-Ce-Ni-Mn quaternary system. Thermodynamic modeling and experimental analysis on phases in the AM sample of Al-Ce-Ni with Mn confirmed that the phases present are consistent with Mn-containing Al-Ce-Ni cast samples. Here, this investigation demonstrates the potential for using secondary alloying elements to drastically alter phase stability and microstructure in alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Aluminum-cerium-manganese alloy embodiments for metal additive manufacturing

Disclosed herein are embodiments of an Al—Ce—Mn alloy for use in additive manufacturing. The disclosed alloy embodiments provide fabricated objects, such as bulk components, comprising a heterogeneous microstructure and having good mechanical properties even when exposed to conditions used during the additive manufacturing process. Methods for making and using alloy embodiments also are disclosed herein.

Allard, Lawrence F.↗
DOE OSTI2023

Grain boundary widening controls siderite (FeCO3) replacement of limestone (CaCO3)

Abstract The microstructure of minerals and rocks can significantly alter reaction rates. This study focuses on identifying transport paths in low porosity rocks based on the hypothesis that grain boundary widening accelerates reactions in which one mineral is replaced by another (replacement reaction). We conducted a time series of replacement experiments of three limestones (CaCO 3 ) of different microstructures and solid impurity contents using FeCl 2 . Reacted solids were analyzed using chemical imaging, small angle X-ray and neutron scattering and Raman spectroscopy. In high porosity limestones replacement is reaction controlled and complete replacement was observed within 2 days. In low porosity limestones that contain 1–2% dolomite impurities and are dominated by grain boundaries, a reaction rim was observed whose width did not change with reaction time. Siderite (FeCO 3 ) nucleation was observed in all parts of the rock cores indicating the percolation of the solution throughout the complete core. Dolomite impurities were identified to act as nucleation sites leading to growth of crystals that exert force on the CaCO 3 grains. Widening of grain boundaries beyond what is expected based on dissolution and thermal grain expansion was observed in the low porosity marble containing dolomite impurities. This leads to a self-perpetuating cycle of grain boundary widening and reaction acceleration instead of reaction front propagation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Using θ' interfaces as templates for planar L1 2 precipitation in AlCuMnZr alloys

Controlled Mn and Zr additions to Al-Cu alloys have allowed for the improved retention of mechanical properties after extended 350°C exposures by stabilizing the main strengthening θ' (Al 2 Cu) phase. Ultimately, θ'/L1 2 (Al 3 Zr) co-precipitate formation stabilizes θ' most effectively; however, Zr diffuses sluggishly and has low solubility in aluminum castings. Increasing the Zr segregation rate would allow for faster and more effective θ'/L1 2 co-precipitation. It is demonstrated that the Zr segregation rate is faster when the Zr matrix content is higher. A much higher Zr matrix content was achieved by rapid cooling during additive manufacturing (AM) that produces θ'/L1 2 co-precipitation faster, which is shown by scanning transmission electron microscopy and atom probe tomography experiments. It was also found that Zr continuously segregates to θ' interfaces up to the most aggressive heat treatment studied such that planar L1 2 precipitates remain after the metastable θ' dissolves. In this manner, we demonstrate that θ' coherent interfaces serve as perfect templates to form stable planar L1 2 precipitates that can provide strength at higher temperatures than traditional θ' strengthened AlCu alloys. This work introduces an alloy design strategy that uses metastable precipitates to quickly nucleate and grow co-precipitates with a desired geometry that contain slow diffusing elements. These ideas can be applied to engineer more heat resistant alloys by taking advantage of high solute matrix contents enabled by rapid cooling during additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Performing In Situ Closed-Cell Gas Reactions in the Transmission Electron Microscope

Gas reactions studied by in situ electron microscopy can be used to capture the real-time morphological and microchemical transformations of materials at length scales down to the atomic level. In situ closed-cell gas reaction (CCGR) studies performed using (scanning) transmission electron microscopy (STEM) can separate and identify localized dynamic reactions, which are extremely challenging to capture using other characterization techniques. For these experiments, we used a CCGR holder that utilizes microelectromechanical systems (MEMS)-based heating microchips (hereafter referred to as "E-chips"). The experimental protocol described here details the method for performing in situ gas reactions in dry and wet gases in an aberration-corrected STEM. This method finds relevance in many different materials systems, such as catalysis and high-temperature oxidation of structural materials at atmospheric pressure and in the presence of various gases with or without water vapor. Here, several sample preparation methods are described for various material form factors. During the reaction, mass spectra obtained with a residual gas analyzer (RGA) system with and without water vapor further validates gas exposure conditions during reactions. Integrating an RGA with an in situ CCGR-STEM system can, therefore, provide critical insight to correlate gas composition with the dynamic surface evolution of materials during reactions. In situ/operando studies using this approach allow for detailed investigation of the fundamental reaction mechanisms and kinetics that occur at specific environmental conditions (time, temperature, gas, pressure), in real-time, and at high spatial resolution.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Isolated Metal Sites in Cu–Zn–Y/Beta for Direct and Selective Butene-Rich C 3+ Olefin Formation from Ethanol

Direct and selective production of C 3+ olefins from bioethanol remains a critical challenge and important for the production of renewable transportation fuels such as aviation biofuels. In this study, we report a Cu–Zn–Y/Beta catalyst for selective ethanol conversion to butene-rich C 3+ olefins (88% selectivity at 100% ethanol conversion, 623 K), where the Cu, Zn, and Y sites are all highly dispersed. The ethanol-to-butene reaction network includes ethanol dehydrogenation, aldol condensation to crotonaldehyde, and hydrogenation to butyraldehyde, followed by further hydrogenation and dehydration reactions to form butenes. Cu sites play a critical role in promoting hydrogenation of the crotonaldehyde C═C bond to form butyraldehyde in the presence of hydrogen, making this a distinctive pathway from crotyl alcohol-based ethanol-to-butadiene reaction. Reaction rate measurements in the presence of ethanol and acetaldehyde (543 K, 12 kPa ethanol, 1.2 kPa acetaldehyde, 101.9 kPa H 2 ) over monometallic Zn/Beta and Y/Beta catalysts indicate that Y sites have higher C–C coupling rates than over Zn sites (initial C–C coupling rate, 6.1 × 10 –3 mol mol Y –1 s –1 vs 1.2 × 10 –3 mol mol Zn –1 s –1 ). Further, Lewis-acidic Y-site densities over Cu–Zn–Y/Beta with varied Y loadings are linearly correlated with the initial C–C coupling rates, suggesting that Lewis-acidic Y sites are the predominant sites that catalyze C–C coupling in Cu–Zn–Y/Beta catalysts. Control experiments show that the dealuminated Beta support is important to form higher density of Lewis-acidic Y sites in comparison with other supports such as silica, or deboronated MWW despite similar atomic dispersion of Y sites and Y–O coordination numbers over these supports, leading to more than 9 times higher C–C coupling rate per mole Y over dealuminated Beta relative to other supports. This study highlights the significance of unique combination of metal sites in contributing to the selective valorization of ethanol to C 3+ olefins, motivating for exploring multifunctional zeolite catalysts, where the presence of multiple sites with varying reactivities and functions allows for controlling the predominant molecular fluxes toward the desired products in complex reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Selective butene formation in direct ethanol-to-C3+-olefin valorization over Zn-Y/Beta and single-atom alloy composite catalysts using in situ generated hydrogen

The selective production of C3+ olefins from renewable feedstocks, especially via C1 and C2 platform chemicals, is a critical challenge for obtaining economically viable low-carbon middle distillate transportation fuels (i.e., jet and diesel). Here, we report a multifunctional catalyst system composed of Zn-Y/Beta and “single-atom” alloy (SAA) Pt-Cu/Al2O3 which selectively catalyzes ethanol-to-olefins (C3+, ETO) valorization in the absence of cofed hydrogen, forming butenes as the primary olefin products. Beta zeolites containing predominately isolated Zn and Y metal sites catalyze ethanol upgrading steps (588 K, 3.1 kPa ethanol, ambient pressure) regardless of cofed hydrogen partial pressure (0-98.3 kPa H2), forming butadiene as the primary product (60% selectivity at 87% conversion). The Zn-Y/Beta catalyst possesses site-isolated Zn and Y Lewis acid sites (at ~7 wt% Y) and Brønsted acidic Y sites, the latter of which has been previously uncharacterized. A secondary bed of SAA Pt-Cu/Al2O3 selectively hydrogenates butadiene to butene isomers at a consistent reaction temperature using hydrogen generated in situ from ethanol-to-butadiene (ETB) conversion. This unique hydrogenation reactivity at near-stoichiometric hydrogen and butadiene partial pressures is not observed over monometallic Pt or Cu catalysts, highlighting these operating conditions as a critical SAA catalyst application area for conjugated diene selective hydrogenation at high reaction temperatures (>573 K) and low H2/diene ratios (e.g., 1:1). Single-bed steady state selective hydrogenation rates, associated apparent hydrogen and butadiene reaction orders, and DFT calculations of the Horiuti-Polanyi reaction mechanisms indicate that the unique butadiene selective hydrogenation reactivity over SAA Pt-Cu/Al2O3 reflects lower hydrogen scission barriers relative to monometallic Cu surfaces and limited butene binding energies relative to monometallic Pt surfaces. DFT calculations further indicate the preferential desorption of butene isomers over SAA Pt-Cu(111) and Cu(111) surfaces while Pt(111) surface favors subsequent butene hydrogenation reactions to form butane over butene desorption events. Under operating conditions without of hydrogen cofeeding, this combination of Zn-Y/Beta and SAA Pt-Cu catalysts can selectively form butenes (65% butenes, 78% C3+ selectivity at 94% conversion) and avoid butane formation using only in situ generated hydrogen, avoiding costly hydrogen cofeeding requirements that hinder many renewable energy processes.

Cordon, Michael↗
DOE OSTI2021

Long-Term 13 C Uptake by 12 C-Enriched Calcite

Knowledge of the exchange of carbon isotopes between dissolved inorganic carbon and calcite minerals is of long-standing importance for the interpretation of sedimentary paleoclimate records and 14 C transport in the geosphere. To assess the mechanism and rates of carbon isotope exchange, we equilibrated 12 C-pure synthetic calcite particles in water, first in a glovebox and then in contact with atmospheric P CO 2 and 13 C/ 12 C ratio, at two different temperatures. Cavity ring-down infrared spectroscopy δ 13 C measurements of the solid revealed sustained 13C incorporation for over a period of 500 days (21 °C) and 125 days (50 °C). We developed a quantitative model for recrystallization and isotope exchange, assuming that the interfacial free energy provides a thermodynamic driving force for the growth of larger particles at the expense of smaller ones. Furthermore, this Ostwald ripening model did not reproduce the kinetics of 13C uptake and required greater coarsening than observed. Rather, the data were best explained by a mechanism involving surface exchange and solid-phase diffusion of 13C into the particles with an inferred effective diffusion constant at 21 °C of about 10 –25 m 2 /s. Although this work cannot rule out the possibility that structural or chemical aspects of the synthetic particles enabled faster 13 C uptake than could be observed in natural systems, this study adds to the body of the recent work, suggesting that fast exchange processes are possible, likely through grain boundaries and other defects.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Single-step selective oxidation of methane to methanol in the aqueous phase on iridium-based catalysts

In this work, one-step conversion of methane to methanol using molecular oxygen as the oxidant in the presence of CO in aqueous solutions on copper or palladium promoted Ir-ZSM-5 catalyst is first reported. The addition of a second metal to Ir-ZSM-5 promotes the catalyst activity, while product selectivity can be tuned either to methanol on IrCu-ZSM-5 or to formic acid exclusively on IrPd-ZSM-5. Most effective is the combination of the three metal species together. Approximately 1200 μmol/g cat methanol, or ~23.4 mol of methanol per mol of Ir, are formed on the IrCuPd trimetallic system (methanol selectivity ~80 %) at 150 °C in 1 h. Our results also demonstrate that atomically dispersed Ir(I)(CO) 2 species formed in the presence of CO can activate the C–H bond of methane to methyl species at temperatures below 150 °C. The good stability in cyclic operation is an additional attribute, rendering this type of catalyst a “front-runner” in future catalyst development for direct methane-to-liquid oxygenates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Oxidation and Associated Pore Structure Modification During Experimental Alteration of Granite

Weathering plays a crucial role in a number of environmental processes, and the microstructure and evolution of multi-scale pore space is a critically important factor in the weathering of geological formations. In igneous rocks the infiltration of meteoric water into initially relatively dry material can cause the rock to begin to disaggregate, increasing porosity and surface area, and allowing further disaggregation and weathering to occur. These processes, in turn, allow biota to colonize the rock, further enhancing the weathering rate. In some igneous rocks this may be driven by oxidation of primary minerals. One such mineral, biotite, has been repeatedly mentioned as a cause of cracking during oxidation. However, the scale-dependence of the processes by which this occurs are poorly understood. We cannot, therefore, accurately extrapolate laboratory reaction rates to the field in predictive numerical models. In order to better understand the effects of oxidation and test the hypothesis that fracture and disaggregation are initiated by swelling of oxidizing biotites, we reacted granite cores in a selenic acid-rich aqueous solution at 200°C for up to 438 days. Elevated temperatures and selenic acid were used to provide relatively fast reaction rates and highly oxidizing conditions in sealed reaction vessels. These experiments were analyzed using a combination of imaging, X-ray diffraction, Mössbauer spectroscopy, and small- and ultra-small angle neutron scattering to interrogate porosity and microfracture formation. The experimental results show little observable biotite swelling, but significant transport and growth of iron oxides and/or clays along grain boundaries throughout the sample. Significant increases in porosity were also observed at the sample rim, likely associated with feldspar alteration. Fractures and transport were observed throughout the core, suggesting that stresses due to crystallization pressures caused by the growing iron phases may be the initiating factors in granite weathering, possibly followed by biotite swelling after sufficient permeability is achieved.

Anovitz, Lawrence M.↗
DOE OSTI2020

The synergistic role of Mn and Zr/Ti in producing θ'/L12 co-precipitates in Al-Cu alloys

Microstructural stability is a critical factor to consider when designing new alloys for high-temperature applications. An Al-Cu alloy with Mn and Zr additions has recently been developed to withstand extended exposures of up to 350 °C. The addition of Mn in combination with Zr and their segregation to precipitate interfaces play a significant role in stabilizing the metastable θ ' precipitates responsible for the alloy&#x27;s hardness; however, adding Zr and Mn separately only improves the stability to 200 °C and 300 °C, respectively. To this end, the effect of the synergistic additions on interfacial structure and chemistry was studied in detail using atom probe tomography (APT) and scanning transmission electron microscopy (STEM) for Al-Cu-Mn-Zr/Ti-containing alloys subjected to long-term annealing (up to 2,100 h) in the critical temperature range, 300 °C and 350 °C, to investigate the role of Zr/Ti in increasing the θ '-precipitate stability. The APT and STEM results reveal that Mn additions stabilize θ ' long enough for the slower diffusing Zr atoms to segregate to coherent θ ' interfaces that eventually create a θ '/ L1 2 -Al 3 (Zr x ,Ti 1-x ) co-precipitate structure. The co-precipitate is highly stable, as shown by density functional theory calculations, and is a key factor that governs microstructural stability beyond 300 °C. This study reveals how solute additions with different stabilization mechanisms can work in concert to stabilize a desired microstructure, and the results provide insights that can be applied to other high-temperature alloy systems.

36 MATERIALS SCIENCE↗