Search NASA⌕ Search

Engineering topics

Allen, C. W.

Publications and source records attributed to Allen, C. W..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Study of ball bearing torque under elastohydrodynamic lubrication

Spinning and rolling torques were measured in an angular-contact ball bearing with and without a cage under several lubrication regimes in a modified NASA spinning torque apparatus. Two lubricants were used - a di-2 ethylhexyl sebacate and a synthetic paraffinic oil, at shaft speeds of 1000, 2000, and 3000 rpm and bearing loads from 45 newtons (10 lb) to 403 newtons (90 lb). An analytical model was developed from previous spinning friction models to include rolling with spinning under lubrication regimes from thin film to flooded conditions. The bearing torque values have a wide variation, under any condition of speed and load, depending on the amount of lubricant present in the bearing. The analytical model compared favorably with experimental results under several lubrication regimes.

Townsend, D. P.↗
NASA NTRS1973

Friction losses in a lubricated thrust-loaded cageless angular-contract bearing

The NASA spinning torque apparatus was modified to measure the spinning torque on a cageless ball thrust bearing. Friction torque was measured for thrust loads varying from 44.5 to 403 newtons (10 to 90 lb) at speeds of 1000, 2000, and 3000 rpm. Tests were conducted with di-2-ethylhexyl sebacate and a synthetic paraffinic oil. These tests were run with either oil jet lubrication or with a thin surface film of lubricant only. An analytical model which included rolling resistance was developed and extended from previous models for spinning torque and lubricant rheology. The model was extended by the inclusion of rolling resistance. The computed values were in fair agreement with the experimental results and confirmed previous hypotheses that a thin lubricant film gives minimum bearing torque and an oil jet flow of a viscous lubricant will result in considerable rolling torque in addition to the torque due to ball spin.

Townsend, D. P.↗
NASA NTRS1973

New generalized rheological model for lubrication of a ball spinning in a nonconforming groove

The elastohydrodynamic theory for predicting the spinning friction of a ball in a nonconforming groove was modified to incorporate a rheological model. The rheological model is based on the exponential pressure viscosity relation for low shear stresses, but at high shear rates and pressures, the relation is altered to one in which the shear stress is porportional to the normal stress. The model was fitted to experimental spinning torques for four different lubricants: a synthetic paraffinic lubricant, di-2-ethylhexyl sebacate, a super-refined naphthenic mineral oil, and a polyphenyl ether (5P4E). Good agreement between the model and experiment was found.

Allen, C. W.↗
NASA NTRS1973

Study of ball bearing torque under elastohydrodynamic lubrication

Spinning and rolling torques were measured in an angular-contact ball bearing with and without a cage under several lubrication regimes in a modified NASA spinning torque apparatus. Two lubricants were used, a di-2 ethylhexyl sebacate and a synthetic paraffinic oil, at shaft speeds of 1000, 2000, and 3000 rpm and bearing loads from 10 lbs to 90 lbs. An analytical model was developed from previous spinning friction models to include rolling with spinning under lubrication regimes from thin film to flooded conditions. The bearing torque values have a wide variation, under any condition of speed and load, depending on the amount of lubricant present in the bearing. The analytical model compared favorably with experimental results under several lubrication regimes.

Townsend, D. P.↗
NASA NTRS1972

An analytical solution for the squeeze film between a nondeformable sphere and groove

An analysis is presented to compute the film thickness, pressure and load relations between a rigid ball and rigid groove in normal approach when lubricated by a fluid with an exponential pressure-viscosity relationship. The geometry of the ball-groove system is reduced to the equivalent system of a paraboloid approaching a flat plate. Exact and approximate solutions are presented for the load and pressure relations. There is found to be a limiting load for a given geometry and lubricant regardless of the rate of approach.

Allen, C. W.↗
NASA NTRS1972

Comparison of conventional and microasperity elastohydrodynamic lubrication of a ballspinning in a nonconforming groove

An analysis was developed for the microasperity elastohydrodynamic lubrication of a ball spinning in a nonconforming groove. This analysis was compared to the conventional elastohydrodynamic analysis of a ball spinning in a nonconforming groove. Rheological models for a di-2-ethylhexyl sebacate, a super-refined naphthenic mineral oil, and a polyphenyl ether (5P4E) were constructed from spinning torque data by using both analyses. The value of the lubricant pressure-viscosity coefficient that makes the data fit the analyses of the fluids differs somewhat from published data. For all three lubricants, an exponential composite model best described the lubricant rheology. Good agreement existed with the experimental and analytical values of torque for both the conventional and microasperity elastohydrodynamic analysis for a spinning ball in a nonconforming groove.

Allen, C. W.↗