Search NASA⌕ Search

Engineering topics

Allison, John E.

Publications and source records attributed to Allison, John E..

At least 19 records

Multiscale in-situ characterization of static recrystallization using dark-field X-ray microscopy and high-resolution X-ray diffraction

Abstract Dark-field X-ray microscopy (DFXM) is a high-resolution, X-ray-based diffraction microstructure imaging technique that uses an objective lens aligned with the diffracted beam to magnify a single Bragg reflection. DFXM can be used to spatially resolve local variations in elastic strain and orientation inside embedded crystals with high spatial (~ 60 nm) and angular (~ 0.001°) resolution. However, as with many high-resolution imaging techniques, there is a trade-off between resolution and field of view, and it is often desirable to enrich DFXM observations by combining it with a larger field-of-view technique. Here, we combine DFXM with high-resolution X-ray diffraction (HR-XRD) applied to an in-situ investigation of static recrystallization in an 80% hot-compressed Mg–3.2Zn–0.1Ca wt.% (ZX30) alloy. Using HR-XRD, we track the relative grain volume of > 8000 sub-surface grains during annealing in situ. Then, at several points during the annealing process, we “zoom in” to individual grains using DFXM. This combination of HR-XRD and DFXM enables multiscale characterization, used here to study why particular grains grow to consume a large volume fraction of the annealed microstructure. This technique pairing is particularly useful for small and/or highly deformed grains that are often difficult to resolve using more standard diffraction microstructure imaging techniques.

36 MATERIALS SCIENCE↗

Quantitative analysis of three-dimensional fatigue crack path selection in Mg alloy WE43 using high-energy X-ray diffraction microscopy

Fatigue short-cracks in Mg alloys display complex growth behavior due to high plastic anisotropy and crack path dependence on local microstructural features. In this study, the three-dimensional crystallography of short-crack paths in Mg alloy WE43 was characterized by mapping near-field high-energy X-ray diffraction microscopy (HEDM) reconstructed grain maps to high-resolution X-ray CT reconstructions of the fracture surfaces in the crack initiation and short-crack growth regions of six ultrasonic fatigue specimens. Crack–grain–boundary intersections were analyzed at 81 locations across the six crack paths. The basal intragranular, non-basal intragranular, or intergranular character of short-crack growth following each boundary intersection was correlated to crystallographic and geometric parameters of the trailing and leading grains, three-dimensional grain boundary plane, and advancing crack front. The results indicate that crack paths are dependent on the combined crystallographic and geometric character of the local microstructure, and crack path prediction can be improved by use of dimensionality reduction on subsets of high-linear-correlation microstructural parameters.

36 MATERIALS SCIENCE↗

Microstructure-Sensitive modeling of surface roughness and notch effects on extreme value fatigue response

Fatigue life knockdown due to surface roughness induces local stress concentrations. Physical fatigue experiments are crucial to qualify materials for use but are limited in their capability to examine the mechanisms underlying the fatigue crack formation driving force due to these stress concentrations. Microstructure-sensitive computational models can aid in this regard and are employed in this work to examine the effects of surface roughness in Al 7075-T6. Digital microstructure models are subjected to crystal plasticity finite element method (CPFEM) simulations to examine the combined effects of microstructure and grain scale asperities on the driving force for fatigue crack formation. Following elastic–plastic shakedown, mesoscale volume-averaged fatigue indicator parameters (FIPs) are computed within fatigue damage process zones of grains. An increase in the intensity of realistic surface roughness profiles corresponds accordingly to larger FIPs but it is difficult to precisely interpret the mechanisms and effects of this intensification. We thus parametrically investigate surface asperities that couple with microstructure and lack of constraint on slip at the free surface to describe microstructure-sensitive surface roughness knockdown effects on fatigue resistance. The depth of a single valley (i.e., notch) due to surface roughness is found to be more detrimental to fatigue resistance than the radius (i.e., notch width, not to be confused with notch acuity). Finally, we also find that different crystallographic textures, grain morphologies, and number of sampled grains have a limited effect on the depth of influence of these notches.

36 MATERIALS SCIENCE↗

Deformation twinning and detwinning in extruded Mg-4Al: In-situ experiment and crystal plasticity simulation

Deformation twinning and detwinning in extruded Mg-4Al were investigated using in-situ SEM-DIC experiments and crystal plasticity finite element (CPFE) simulation. In this study, the in-situ SEM-DIC method was used to provide a unique set of data including twin/detwin characteristics and twin area fraction in addition to strain maps. A statistical analysis of the activation of twin variants and twin area fraction during both twinning and detwinning was conducted. A strong correlation was found between twin growth/shrinkage and the Schmid Factor (SF) for individual twin variants Higher twin SF during loading and unloading led to higher twin growth and shrinkage, respectively. However, after the applied compressive strain was removed, the pattern of the twin area fractions of the residual twin variants versus their nominal SFs did not follow the trend observed at the maximum compressive strain. Using a systematic methodology and an advanced twin/detwin model, the PRISMS-Plasticity CPFE simulation was calibrated using experimentally determined stress versus strain and twin area fraction versus strain information. A comprehensive evaluation of the CPFE model was conducted to determine its ability to capture the statistics of twin variants activation and twin area fraction. CPFE accurately captured the statistical aspects of both twinning and detwinning. Finally, it also predicted the first dominant twin variant for 47.5% of the grains and at least one of the two dominant twin variants for 80% of the grains at maximum compressive strain.

36 MATERIALS SCIENCE↗

Simulated effects of sample size and grain neighborhood on the modeling of extreme value fatigue response

Assessing the size of representative volume elements (RVEs) for fatigue-related applications is challenging. A RVE relevant to random microstructure requires a volume of material that is sufficiently large to capture the grain/phase heterogeneity that captures all statistical moments of the distribution of the driving force for fatigue crack formation at “hot spot” grains. Consequently, the large size of a microstructure RVE required to study fatigue phenomena is largely computationally intractable and difficult to explore. A more realistic objective in this work is to systematically study, as a function of the size of a statistical sample of microstructure, trends towards convergence of the simulated distribution of driving force for fatigue crack formation. Our present work accordingly leverages the recently developed open-source PRISMS-Fatigue framework to examine the trends in convergence of extreme value distributions (EVD) of Fatigue Indicator Parameters (FIPs) in progressively larger polycrystalline microstructure realizations of FCC Al alloy 7075-T6 using crystal plasticity finite element method simulations. The results are compared to the traditional method in which ensembles of statistical volume elements (SVEs) are simulated to build up statistics intended to approximate those associated with a larger volume of material. The convergence of EVDs with increase of size of a SVE of microstructure is closely related to the extent of grain nearest neighbor (NN) interactions. Accordingly, the sensitivity of the local micromechanical response at hot spot grains is quantitatively investigated by systematically varying the orientations of NN grains. Results indicate that SVEs with cubic crystallographic texture tend towards convergence of the EVD of FIPs with tens of thousands of grains while the random and rolled textures require larger volumes. Simple relationships based on microstructure parameters (e.g., Schmid Factor, grain size, NN misorientation) do not completely correlate to fatigue hot spot grains. Finally, the sensitivity of the extreme value fatigue response at hot spot grains extends to the 3rd NN when a single neighborhood grain orientation is altered.

36 MATERIALS SCIENCE↗

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys

Abstract The effect of Ca and Zn additions on the microstructure and texture evolution during thermomechanical processing of Mg-Zn-Ca sheet alloys was systematically investigated and quantified. Plane strain compression testing in a Gleeble thermomechanical simulator was used to physically simulate a 10-pass rolling schedule, while allowing for careful control and monitoring of the processing parameters. Textures in the as-deformed ternary alloy samples demonstrate a weak maximum basal intensity and spreading in the transverse direction. Increasing the Zn content to 3.2 wt.% in the ternary alloys resulted in samples that exhibited weak textures in the as-deformed state. Importantly, static recrystallization (SRX) during post-deformation annealing of these alloys promoted a desirable annular texture, with the c -axis tipped from the normal direction and a lower basal texture intensity. The evolution in texture during SRX is associated with as-deformed microstructures with broad grain orientation spreads and a low degree of recrystallization.

36 MATERIALS SCIENCE↗

PRISMS-Fatigue computational framework for fatigue analysis in polycrystalline metals and alloys

Abstract The PRISMS-Fatigue open-source framework for simulation-based analysis of microstructural influences on fatigue resistance for polycrystalline metals and alloys is presented here. The framework uses the crystal plasticity finite element method as its microstructure analysis tool and provides a highly efficient, scalable, flexible, and easy-to-use ICME community platform. The PRISMS-Fatigue framework is linked to different open-source software to instantiate microstructures, compute the material response, and assess fatigue indicator parameters. The performance of PRISMS-Fatigue is benchmarked against a similar framework implemented using ABAQUS. Results indicate that the multilevel parallelism scheme of PRISMS-Fatigue is more efficient and scalable than ABAQUS for large-scale fatigue simulations. The performance and flexibility of this framework is demonstrated with various examples that assess the driving force for fatigue crack formation of microstructures with different crystallographic textures, grain morphologies, and grain numbers, and under different multiaxial strain states, strain magnitudes, and boundary conditions.

Chemistry↗

The effects of heat treatment on the response of WE43 Mg alloy: crystal plasticity finite element simulation and SEM-DIC experiment

The present report addressed the effects of heat treatment on the mechanical response of a WE43 Mg alloy using an integrated framework of SEM-DIC experiment and CPFE simulation. Both macroscopic responses including yield strength, ultimate strength, ductility, and microscopic responses, including local displacement and strain maps, were experimentally investigated. The focus of this work is to use the CPFE simulation as an integrated computational tool to study the effects of heat treatment. The CPFE framework was evaluated using the local fields of displacement and strain obtained from the SEM-DIC experiment rather than the conventional scheme of using macroscopic responses at different loading directions. Subsequently, the information which is available using CPFE, such as the critical resolved shear stress (CRSS) and relative slip activity, was used to study the effects of heat treatment on the response of WE43 Mg alloy. The contributions of different strengthening mechanisms on the CRSS were addressed. The results show that effects of heat treatment can be captured using the predominant mechanisms of the grain size effect and the influence of precipitates. Finally, it has been shown that classical Hall-Petch in which one constant can capture the size effects, should be modified. To do so, each deformation mode should have a unique Hall-Petch constant, which are calculated here for the WE43 Mg alloy.

36 MATERIALS SCIENCE↗

Dislocation cross-slip in precipitation hardened Mg–Nd alloys

An integrated experimental characterization and molecular dynamics (MD) simulation approach was used to explore the dislocation-precipitate interactions in a dilute Magnesium–Neodymium (Mg–Nd) precipitation hardened alloy. In situ indentation in a transmission electron microscope (TEM) and postmortem TEM characterization of deformed samples and MD simulations revealed that basal < a > type dislocations interacted differently with β 1 (Mg 3 Nd) and β"(Mg 3-7 Nd) precipitates. For β" precipitates, the basal dislocations directly shear the precipitates. For β 1 precipitates, such shearing becomes much more difficult because it requires the creation of antiphase boundaries in the ordered lattice of β 1 precipitates. Screw dislocations were observed to cross-slip from basal to the prismatic plane, which could be parallel to the broad facet of β 1 precipitates. It is postulated that double cross-slip (basal to prismatic to basal) via the Hirsch mechanism may enable screw dislocations to overcome the β 1 precipitates. MD simulations also revealed that an edge dislocation is unable to bypass the precipitate via the generation of screw dislocation segments plus the double cross-slip mechanism. The edge dislocation can bow around the precipitate, and the segment that adopts a screw character can cross-slip to the prismatic plane but with increasing applied stress, cross-slips back to the original basal plane to continue glide via precipitate shearing. Finally, the implication of glide dislocation - β 1 -precipitate interaction mechanisms on the strength and ductility of β 1 precipitate dominant microstructures is discussed.

36 MATERIALS SCIENCE↗

Multiscale modeling of twinning and detwinning behavior of HCP polycrystals

A multiscale scheme is presented here to capture the twinning and detwinning mechanisms during cyclic loading of HCP polycrystals. In the current framework, the crystal plasticity finite element (CPFE) method is employed at the microstructural scale. The response of twinned regions at a material point is calculated using a novel homogenization scheme via a Taylor-type model. The homogenized behavior is then used in the CPFE to obtain the response of a polycrystal. An efficient rate-independent crystal plasticity model that has been incorporated into the open source PRISMS-Plasticity software is introduced here to capture the response of the twinned region. Accordingly, the corresponding algorithmic tangent modulus is derived. Finally, this multiscale scheme is validated against data available for the cyclic response of Mg alloy ZK60A. The results show that the multiscale model can capture the key elements of the sample response observed during the experiment.

36 MATERIALS SCIENCE↗

PRISMS-Plasticity: An open-source crystal plasticity finite element software

An open-source parallel 3-D crystal plasticity finite element (CPFE) software package PRISMS-Plasticity is presented here as a part of PRISMS integrated framework. A highly efficient rate-independent crystal plasticity algorithm is implemented along with developing its algorithmic tangent modulus. Additionally, a twin activation mechanism is incorporated into the framework based on an integration point sensitive scheme. The integration of the software as a part of the PRISMS framework is demonstrated. To do so, the integration of the PRISMS-Plasticity software with experimental characterization techniques such as electron backscatter diffraction (EBSD) and synchrotron X-ray diffraction using available open source software packages of DREAM.3D and Neper is elaborated. The integration of the PRISMS-Plasticity software with the information repository of Materials Commons is also presented. The parallel performance of the software is characterized which demonstrates that it scales well for large problems running on hundreds of processors. Various examples of polycrystalline metals with face-centered cubic (FCC), body-centered cubic (BCC), and hexagonal close-packed (HCP) crystals structures are presented to show the capability of the software to efficiently solve crystal plasticity boundary value problems, in addition to integration with preprocessing and postprocessing tools. PRISMS-Plasticity is an important activity within the broader PRISMS Center and future enhancements to PRISMS-Plasticity are planned and will be described.

36 MATERIALS SCIENCE↗

Phase Transformation Kinetics and Alloy Microsegregation in High Pressure Die Cast Magnesium Alloys (Final Report)

The primary objective of this project is to conduct a systematic, quantitative study of phase transformation kinetics and microsegregation in HPDC Mg alloys in both as-cast and heat treated conditions. These results will be used to develop and validate physics-based phase transformation kinetics micro-models that quantitatively capture microstructural evolution and microsegregation during HPDC and heat treatment of Mg alloys. Finally, this knowledge will be transferred to industry and the wider research community through these micro-models and the experimental data that will be stored in the National Institute of Standards and Technology (NIST)-DOE Energy Efficiency and Renewable Energy Advanced Automotive Cast Magnesium Alloys Repository, as well as a new repository, the University of Michigan Department of Energy Predictive Integrated Structural Materials Science (UM DOE PRISMS) Materials Commons. To accomplish these goals, a systematic and comprehensive experimental study is being combined with computational modeling and simulation.

36 MATERIALS SCIENCE↗