Engineering topics

Alper, Koray

Publications and source records attributed to Alper, Koray.

4 records

DOE OSTI2024

Hydrocoals from waste biomass via catalytic hydrothermal carbonization processing

This study investigates how operating conditions (temperature and residence time) and benzoyl chloride impact hydrochar production from almond shells through hydrothermal carbonization. Carbon content rises while volatile matter decreases with increasing temperature, yielding a hydrochar with an estimated heating value of 28 MJ/kg. Elevated temperatures lower the O/C and H/C atomic ratios of hydrochars. Even at the lowest temperature under scrutiny, catalytic experiments using benzoyl chloride enhance carbonization and fuel ratio across all temperatures. Hydrochars produced through catalytic runs demonstrate elevated fuel ratios relative to those generated through noncatalytic runs, despite operating under the same conditions. These insights reveal the capacity of benzoyl chloride as a catalyst to improve hydrochar properties, suggesting its utility for advancing both the efficiency and effectiveness of hydrothermal carbonization processes.

09 BIOMASS FUELS↗

DOE OSTI2021

Use of a Lewis acid, a Brønsted acid, and their binary mixtures for the hydrothermal liquefaction of lignocellulose

The main objective of the present study is to investigate the effect of a Lewis acid, Brønsted acid, and their combined use on the hydrothermal liquefaction of lignocellulosic biomass. Hydrothermal liquefaction of teak wood was conducted at 250, 300 and 350 °C for 15, 30 and 60 min. Hydrothermal liquefaction of teak wood was carried out at 300 °C for 30 min (the best optimum conditions) without and with the use of Mg(ClO 4 ) 2 , HClO 4 , and HClO 4 /Mg(ClO 4 ) 2 at various loadings (2–10 mmol/15 g wood). The highest bio-oil yield was obtained with the non-catalytic run. All tested catalysts have negative effect on bio-oil yields. The bio-oil yields generally decreased with increasing the catalyst loadings. The deoxygenation degree in bio-oils changed depending on the type of catalyst and loading. A high degree of de-oxygenation took place with Mg(ClO 4 ) 2 catalysts. An increased catalyst loading led to decreased aromatic contents of bio-oils catalyzed by either Mg(ClO 4 ) 2 or HClO 4 . The use of a catalyst increased total naphtha fractions in bio-oils. The highest heating value of the bio-oil was estimated to be approximately 30 MJ/kg. Gas chromatography–mass spectrometry analysis revealed that the bio-oils from the non-catalytic and catalytic runs contained aldehydes, ketones, phenols, acids, esters and alcohols. Furthermore, the relative yields of the oxygenated compounds were affected by catalyst type.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Sustainable energy and fuels from biomass: a review focusing on hydrothermal biomass processing

Fossil fuels are being replaced with renewable energy resources (biomass and biomass waste, solar, geothermal, wind, etc.) to ensure sustainable development, reduce the dependence on fossil fuels, address environmental challenges including climate change. Today, biomass produces 5 × 10 19 kJ of energy/year, which corresponds to 10% of the annual global energy consumption. Considering the variety of biomass resources, this value is predicted to reach 150 × 10 19 kJ by 2050. Biomass may become even more important for use as an energy resource and chemical raw material in the 21st century. Hydrothermal biomass conversion stands out as a promising and alternative technology. Methods such as traditional gasification and pyrolysis require dry biomass. Hydrothermal techniques have been developed to eliminate the cost and time required for drying biomass. The purpose of this process is to decompose biomass with a high moisture content into small molecules and reduce its oxygen content to obtain liquid fuels or valuable chemicals. Finally, this review presents the current and future state of energy, energy sources, biomass properties and biomass conversion technologies with a focus on hydrothermal technologies.

09 BIOMASS FUELS↗

DOE OSTI2020

One-step transformation of biomass to fuel precursors using a bi-functional combination of Pd/C and water tolerant Lewis acid

Direct one-pot transformation of lignocellulosic biomass has been developed as an effective and sustainable strategy to produce fuel blend stocks and high value chemical building blocks. In this wok, a bi-functional catalyst system consisting of palladium supported on carbon (Pd/C) and metal triflates (i.e., Sm(OTf) 3 , La(OTf) 3 , and Cu(OTf) 2 ) were shown to promote the biomass liquefaction in both hot-compressed water and supercritical ethanol medium, converting fir wood into oxygenated compounds. We report the highest bio-oil yield from hydrothermal liquefaction (HTL) was 10.47 wt% over Pd/C whereas the highest bio-oil yield of 49.71 wt% was achieved from supercritical ethanol liquefaction (SCEL) over the bi-functional catalyst system of Pd/C and La(OTf) 3 . Higher heating values, carbon recovered values and boiling point distributions were further determined for elucidating the physical properties of the bio-oils. Gas chromatography mass spectrometry (GC–MS) analysis of the bio-oils revealed the chemical composition of the bio-oils. Substituted phenols and cyclopentenone/cyclopentanone type compounds consisted of more than 60 area% of the total products from HTL, whereas phenol and esters represented the major products from SCEL. The major reaction pathways are proposed based on the GC–MS results, which include depolymerizaton, isomerization, dehydration, condensation, and hydrogenation.

09 BIOMASS FUELS↗