Engineering topics

Altenkirch, R. A.

Publications and source records attributed to Altenkirch, R. A..

At least 19 records

NASA NTRS2003

Sounding Rocket Microgravity Experiments Elucidating Diffusive and Radiative Transport Effects on Flame Spread over Thermally-Thick Solids

A series of 6-minute microgravity combustion experiments of opposed flow flame spread over thermally-thick PMMA has been conducted to extend data previously reported at high opposed flows to almost two decades lower in flow. The effect of flow velocity on flame spread shows a square root power law dependence rather than the linear dependence predicted by thermal theory. The experiments demonstrate that opposed flow flame spread is viable to very low velocities and more robust than expected from the numerical model, which predicts that at very low velocities (less than 5 centimeters per second), flame spread rates fall off more rapidly as flow is reduced. It is hypothesized that the enhanced flame spread observed in the experiments may be due to three- dimensional hydrodynamic effects, which are not included in the zero-gravity, two-dimensional hydrodynamic model. The effect of external irradiation was found to be more complex that the model predicted over the 0-2 Watts per square centimeter range. In the experiments, the flame compensated for the increased irradiation by stabilizing farther from the surface. A surface energy balance reveals that the imposed flux was at least partially offset by a reduced conductive flux from the increased standoff distance, so that the effect on flame spread was weaker than anticipated.

Olson, Sandra L.↗

NASA NTRS1999

Reflight of the Solid Surface Combustion Experiment: Flame Radiation Near Extinction

In flame spreading in quiescent and low-velocity opposing flows, effects of surface reradiation and flame radiation are important in establishing the spread rate and whether the flame, once ignited, survives to steady spread or extinguishes after a time long compared to the ignition event. A reflight of the Solid Surface Combustion Experiment (SSCE), supported by modelling, demonstrates that for thick, flat fuels, the ultimate fate of the flame is extinction rather than steady spread. A mismatch between the thermal scale in the gas, driven by radiation, and the species diffusion scale, driven by mass diffusion, develops such that the high temperature regions of the flame are ultimately located in a region to which oxygen cannot be supplied at a sufficient rate to sustain reaction, and extinction occurs. Results of the experiment conducted on Space Shuttle mission STS 85 on 9 August 1997 are reviewed. For the flat surface geometry, while the hydrodynamic phenomena associated with opposed-flow flame spread may be treated two dimensionally, the radiative effects are three dimensional, and so modelling the radiative processes, with the mismatch in dimensionality, is difficult. The cylindrical geometry at least one long compared to the radius, provides a configuration in which the radiative processes for spread in the axial direction are two dimensional, thus simplifying the modelling. The cylindrical geometry allows for the development of more sophisticated radiative models without the complication of dimensionality concerns, e.g., discrete transfer, which is discussed in detail by Bundy (1998). Additionally, the cylindrical geometry results in a "focussing" of the heat transfer to the surface and may allow for steady spread for radii that for thick fuels of the same half-thickness there is no steady spread.

Altenkirch, R. A.↗

NASA NTRS1999

Diffusive and Radiative Transport in Fires (DARTFire): Opposed-Flow Flame Spread in Low-Velocity Flows

For flames spreading into a low-velocity flow that can only be obtained in microgravity, we have observed behavior that is different from that which is obtained at higher velocities where radiative effects are unimportant and species transport is relatively fast. Unfortunately, lack of a large body of low-gravity flame spread experimental data inhibits progress in developing an understanding of the physics of low-velocity, opposed-flow flame spread phenomena. Recent DARTFire sounding rocket experimental studies though, coupled with developing theory and modelling, have allowed some strides in understanding to be made, on which we report here. Four launches to date have resulted in six experiments for opposed-flow flame spread over a thick PMMA sample. During the 6 min microgravity period, the PMMA samples were ignited, and steady flame spread was studied under varied flow velocity, oxidizer atmospheric conditions, and, because radiative heat transfer is so important in these slowly spreading flames, external radiant flux. These were the first attempts at such experimental control and measurement in microgravity. A recent reflight of the Solid Surface Combustion Experiment (SSCE) has demonstrated, as modelling predicts, that for the thick fuel of the DARTFire experiment, flame spread in a quiescent environment is a transient process evolving from ignition to extinction on the order of 600 s (Altenkirch et al., 1999). Further study then of the effects of radiation in the very low-velocity opposing flows is of interest in understanding the transition from steady, sustained spread to the unsteady evolution to extinction as the opposing flow is reduced further and eventually removed.

Altenkirch, R. A.↗

NASA NTRS1991

Heat Transfer to a Thin Solid Combustible in Flame Spreading at Microgravity

The heat transfer rate to a thin solid combustible from an attached diffusion flame, spreading across the surface of the combustible in a quiescent, microgravity environment, was determined from measurements made in the drop tower facility at NASA-Lewis Research Center. With first-order Arrhenius pyrolysis kinetics, the solid-phase mass and energy equations along with the measured spread rate and surface temperature profiles were used to calculate the net heat flux to the surface. Results of the measurements are compared to the numerical solution of the complete set of coupled differential equations that describes the temperature, species, and velocity fields in the gas and solid phases. The theory and experiment agree on the major qualitative features of the heat transfer. Some fundamental differences are attributed to the neglect of radiation in the theoretical model.

Bhattacharjee, S.↗

NASA NTRS1991

The effect of surface radiation on flame spread in a quiescent, microgravity environment

In most theories of laminar flame spread over solid combustibles, radiation is neglected. However, when gas motion is completely absent, which may occur in the quiescent, microgravity environment of a spacecraft, the importance of radiation compared to convection is enhanced. Here, a theoretical model is developed of flame spread over a thin solid fuel into an opposing flow of oxidizer, the opposing flow being present in the quiescent environment in flame-fixed coordinates, including the effects of radiative heat transfer from the fuel surface. Numerical solutions to the conservation equations in the gas and the solid phase that describe the spreading flame are presented for a variety of ambient conditions and surface emittances. When surface radiation is significant, the solid surface acts as a heat sink, causing the flame to cool, shrink in size, and spread more slowly. Better agreement with experiment for net heat transfer to the surface is obtained when surface radiation is included. For low ambient oxygen levels, radiative effects lead to flame extinction. A radiation/conduction parameter is identified that adequately describes the importance of surface radiation.

Bhattacharjee, S.↗

NASA NTRS1989

The solid surface combustion space shuttle experiment hardware description and ground-based test results

The Lewis Research Center is developing a series of microgravity combustion experiments for the Space Shuttle. The Solid Surface Combustion Experiment (SSCE) is the first to be completed. SSCE will study flame spreading over thermally thin fuels (ashless filter paper) under microgravity conditions. The flight hardware consists of a combustion chamber containing the sample and a computer which takes the data and controls the experiment. Experimental data will include gas-phase and solid-phase temperature measurements and motion pictures of the combustion process. Flame spread rates will be determined from the motion pictures.

Vento, D. M.↗

NASA NTRS1989

The solid surface combustion Space Shuttle experiment hardware description and ground-based test results

Vento, D. M.↗

NASA NTRS1989

Opposed-flow flame spread and extinction in mixed-convection boundary layers

Experimental data for flame spread down thin fuel samples in an opposing, mixed-convection, boundary-layer flow are analyzed to determine the gas-phase velocity that characterizes how the flame reacts as it spreads toward the leading edge of the fuel sample into a thinning boundary layer. In the forced-flow limit where the cube of the Reynolds number divided by the Grashof number, Re exp 3/Gr, is large, L(q)/L(e), where L(q) is a theoretical flame standoff distance at extinction and L(e) is the measured distance from the leading edge of the sample where extinction occurs, is found to be proportional to Re exp n with n = -0.874 and Re based on L(e). The value of n is established by the character of the flow field near the leading edge of the flame. The Re dependence is used, along with a correction for the mixed-convection situation where Re exp 3/Gr is not large, to construct a Damkohler number with which the measured spread rates correlate for all values of Re exp 3/Gr.

Altenkirch, R. A.↗

NASA NTRS1985

Solid Surface Combustion at Reduced Gravity

The spread of a flame in the gas over the surface of a solid combustible involves in an essential way the transfer of heat from the flame to the solid fuel immediately ahead of it. This heat transfer is affected by the character of the gas phase flame, and so the phenomenon of flame spreading under reduced gravity, in which the flow is generated by gasification of the solid combustible, is apt to be different from what occurs under the Earth's normal gravitational acceleration where the flow is largely buoyancy driven. An experiment is being designed for the Middeck of the Space Shuttle to aid us in understanding the process of flame spreading in the absence of a buoyancy driven flow. A chamber approximately 0.35 cu.m. in volume is to contain either a thin sample of a cellulosic material or a thick sample of polymethyl-methacrylate and an oxidizing environment of O2 and N2. Samples will be ignited at one end, and the ensuing flame spread will be filmed. The spread rate can be determined from the films, and surface and gas-phase temperatures just above the surface will also be recorded. These data will help to clarify the mechanism of forward heat transfer in the low gravity flames.

Altenkirch, R. A.↗

NASA NTRS1985

Backward boundary layers in downward flame spread

The gas-phase combustion of a vertical fuel slab pyrolyzing at a finite rate under downward flame spread conditions is investigated theoretically. The backward boundary layer character of the flow is exploited, and a transformation that shifts the singularity associated with boundary-layer equations to a location, upstream of flame lift-off, where the surface temperature is nearly ambient, is employed. The boundary-layer flow is matched asymptotically for large Grashof number to a potential flow that allows the flow induced by the flame and along the upstream surface of the fuel bed to be calculated. Gas-phase temperature and velocity predictions are compared to experiment, and although analysis of the gas phase is emphasized, an approximate spread rate, based on a solid-phase energy balance, is calculated.

Vedha-Nayagam, M.↗

NASA NTRS1984

Gravitational effects on flames spreading over thick solid surfaces

A theoretical model for the downward spread of a flame in the gas over a semi-infinitely thick fuel bed is presented. Gas-phase chemistry is assumed to proceed at an infinite rate while the fuel bed is taken to pyrolyze at the surface in an Arrhenius fashion. Spread rates and flame shapes are computed for two different ambient oxygen concentrations for gravitational accelerations both below and above that of the earth. Predicted spread rates decrease and actual flame size increases with decreasing gravity. Results agree favorably with available, experimental results and expected results from reduced gravity experimentation.

Vedha-Nayagam, M.↗

NASA NTRS1983

Correlating downward flame spread rates for thick fuel beds

Flame spread rates are presented for polymethylmethacrylate fuel beds as a function of gravitational acceleration and ambient pressure and oxygen concentration. The data are correlated by plotting a dimensionless spread rate that is a measure of the heat transferred forward of the flame, required to sustain the flame, compared to the maximum possible forward heat transfer against a Damkoehler number. The latter parameter indicates the approach of the flame to its maximum temperature, where the maximum possible forward heat transfer occurs, such that the dimensionless spread rate approaches unity at large Damkoehler number. Surface regression effects on the flame spread process are incorporated into the dimensionless spread rate, and the final correlation is independent of bed thickness.

Altenkirch, R. A.↗

NASA NTRS1982

Boundary integral equation method calculations of surface regression effects in flame spreading

A solid-phase conduction problem that is a modified version of one that has been treated previously in the literature and is applicable to flame spreading over a pyrolyzing fuel is solved using a boundary integral equation (BIE) method. Results are compared to surface temperature measurements that can be found in the literature. In addition, the heat conducted through the solid forward of the flame, the heat transfer responsible for sustaining the flame, is also computed in terms of the Peclet number based on a heated layer depth using the BIE method and approximate methods based on asymptotic expansions. Agreement between computed and experimental results is quite good as is agreement between the BIE and the approximate results.

Altenkirch, R. A.↗

NASA NTRS1982

Buoyancy effects on the temperature field in downward spreading flames

It is shown that flames which spread vertically down thermally thin fuels at the same Damkoehler number, and therefore have the same dimensionless spread rate, also have the same dimensionless temperature fields irrespective of differences in physical size. The Frey and Tien (1976) effects of pressure on flame size are due to the effects of pressure on the character of the induced buoyant flow.

Altenkirch, R. A.↗

NASA NTRS1980

A transformation of the boundary layer equations for free convection past a vertical flat plate with arbitrary blowing and wall temperature variations

A transformation of the laminar boundary layer equations, similar to the transformation of Kao et al. (1977), is presented which allows arbitrary distributions of both wall temperature and blowing. The procedure yields constant boundary conditions, but variable coefficients appear in the differential equations. The proposed transformation is applicable to the problem of downward burning of vertical pieces of condensed-phase combustibles.

Vedhanayagam, M.↗

NASA NTRS1980

Buoyancy effects on flames spreading down thermally thin fuels

Experiments show that buoyancy influences the downward spread rate of flames consuming thermally thin fuel beds. For index cards (0.0098 cm half-thickness) and adding-machine tape (0.0043 cm half-thickness), an increase in the buoyancy level causes the spread rate to drop until no flame propagation is possible. A dimensionless spread rate is found to correlate with a Damkoehler number. As the Damkoehler number increases with decreasing buoyancy level brought about by an increase in pressure or a decrease in gravity, the dimensionless spread rate approaches unity. It is also found that a small change in orientation with respect to the vertical is equivalent to a change in the magnitude of gravity in the direction of spread, and power-law relations between the dimensional spread rate and pressure are only valid over a small pressure range.

Altenkirch, R. A.↗

NASA NTRS1978

An experimental study of the influence of elevated buoyancy levels on flame spread rate over thermally thin cellulosic materials

The role of buoyancy on the flame spread rate over paper and its effect on extinction was studied by changing the gravity level and pressure. It was found that the flame spread rate decreases as the buoyancy induced flow increases. A method for correlating flame spread data using dimensionless parameters is presented. The Damkohler number is shown to be the dependent variable.

Shang, P. C.↗

NASA NTRS1977

Buoyancy induced extinction of laminar gas jet diffusion flames

The behavior of laminar gas jet diffusion flames subjected to elevated gravity in order to investigate the role of buoyancy in such flames has been studied experimentally. Higher than earth normal gravity was achieved using a 1.83 m diameter centrifuge. Methane, ethane, propane and hydrogen air flames were stabilized at the exit of small tubular burners ranging in size from .05 to .21 cm in diameter. The experimental arrangement was such that the flames were burnt vertically upward. Following a shortening of the flame and a decrease in luminosity with increasing gravity level, further increases in gravity caused the hydrocarbon flames to separate from the rim and eventually extinguish. The extinction gravity levels appear to correlate with the parameter g alpha (u)/S to the 3rd (u), which should be a constant for buoyancy controlled extinction. This parameter is developed by a rudimentary analysis of the heat loss from the premixed stabilizing flame in the lifted flame base. When the loss is excessive, the flame is extinguished.

Altenkirch, R. A.↗