Search NASA⌕ Search

Engineering topics

Alvarado, Vladimir

Publications and source records attributed to Alvarado, Vladimir.

16 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Final Technical Report: Center for Mechanistic Control of Unconventional Formations

The overarching mission of the Center for Mechanistic Control of Unconventional Formations (CMC-UF) was to garner cross-cutting, fundamental, geoscience knowledge to achieve mechanistic control over the strongly coupled nonequilibrium physical and geochemical processes in extreme geological environments including shale, mudstone, marls, and other tight rocks with nanoscale pores. Collectively, these are referred to as unconventional formations and they often play the role of seals for other subsurface storage formations. The fundamental knowledge garnered by CMC-UF enabled science-based management of US unconventional formations for subsurface storage of carbon dioxide and TWh quantities of renewable energy as hydrogen and/or compressed air over longer timeframes as well as for natural gas production, with reduced environmental impacts, in the short term.

58 GEOSCIENCES↗
DOE OSTI2022

Effects of Supercritical CO 2 Injection on the Shale Pore Structures and Mass Transport Rates

Characterizing the pore structures and transport properties of low-permeability shales is critical for evaluating these formations as potential seals or storage sites for geological CO 2 sequestration. Here, we use low-pressure gas adsorption in conjunction with nuclear magnetic resonance (NMR) to characterize the pore-size distribution of shales before and after injection of supercritical CO 2 . Nitrogen gas was used as the detecting phase for the adsorption experiments and pentane liquid was used for the NMR experiments. We also performed time-resolved NMR and gravimetric microbalance measurements to observe mass transport during desaturation. We use these data to estimate the self-diffusion coefficient of pentane and changes in the saturation state of the pore network. We analyzed samples with a range of compositions from the Wolfcamp shale before and after exposure to supercritical CO 2 for 3 days. Integrating the gas adsorption and NMR data shows how supercritical CO 2 injection alters the pore-size distribution for pore sizes <1 nm to 1 mm. Finally, our results provide insights on how the pore structure and mass transport properties of different shale lithologies may evolve during storage of supercritical CO 2 .

58 GEOSCIENCES↗
DOE OSTI2022

Dynamic stability of a crude oil/brine interface: Effect of anion type

The chemical composition of the aqueous phase plays an essential role in water-based enhanced-oil recovery processes. The aqueous phase ionic profile affects the snap-off response of a crude oil-brine system by linking it to the brine-crude oil interfacial rheology. In this work, we focus on the effect of the anion on the snap-off response. To this end, a sample of crude oil from the Minnelusa Sandstone formation in Wyoming was selected, and several aqueous solutions were prepared with salts containing sodium cation and different anions (chlorides, sulfates, and phosphates) at two ionic strength values, 0.6 M and 6 mM, as cases of high- and low-salinity water. Interfacial tension, interfacial viscoelasticity and interface stability were analyzed as functions of aging time using pendant drop, dilatational rheology, and liquid bridge techniques, respectively. Here the results show that solutions with higher ionic strength led to the formation of more rigid interfaces, i.e. higher elastic modulus, and faster formation kinetics. In the low-salinity regime, solutions with polyvalent anions produce more viscoelastic interfaces at faster rates than solutions with monovalent anions. Finally, an excellent correlation (R 2 greater than 0.97) between the relative stability of the interfacial film, predicted in liquid bridge tests, and the ratio of interfacial tension and interfacial elastic modulus was found.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Multimodal study of the impact of stimulation pH on shale pore structure, with an emphasis on organics behavior in alkaline environments

The tight nature of shale formations calls for hydraulic fracturing techniques able of altering the pore architecture to facilitate the production of hydrocarbon resources. The composition, pH, salinity, density and chemistry of Hydraulic Fracturing Fluids (HFF) vary substantially depending on reservoir characteristics. pH is among the most important stimulation fluid properties, ranging from very acidic, for carbonate reservoirs, to basic, in the case of clay-rich formations. pH regulates what geochemical reactions take place between the stimulation fluid and shale, as well as pore architecture alteration. The dissolution of carbonates and pyrite, and the precipitation of common minerals such as barite, gypsum and iron oxides in acidic environments have been extensively documented. In contrast, alkali stimulation environments and the role of organic components have received less attention. This research provides insight into the role of both minerals and organic components during alkaline stimulation, and the resulting pore architecture alterations. Here, a set of reactive experiments are performed using three different shales, with varying organic matter (OM) content, at different pH (3, 6, 8, 10, 12). The analysis of pore architecture alteration induced by the reaction was performed via nitrogen (N2) gas adsorption and Time-Domain Nuclear Magnetic Resonance (TD-NMR). Inductively Coupled Plasma - Optical Emission Spectrometry (ICP-OES) was used to measure the composition of the stimulation fluid post-reaction. The system with a larger impact on the pore architecture (pH 12) underwent a more extensive analysis through the application of Focused Ion Beam Scanning Electron Microscopy (FIB-SEM) and x-ray Diffraction (XRD). Results show that mineral dissolution contributed to the creation of secondary porosity, mainly through dissolution of clays and silicates. We show that the abundance and distribution of organic matter both play a significant role in changes in pore architecture. Most samples showed an increase in inter-organic porosity, likely due to the organic acids within kerogen reacting with the stimulation fluid. Samples with a larger amount and more widespread distribution of organic matter show the most significant alterations. Finally, we also highlight the dissolution process of iron-rich minerals, including framboidal pyrite, as another important source of secondary porosity.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2022

Probing ethane phase changes in bead pack via high-field NMR spectroscopy

Phase equilibria analysis in two-phase systems requires discernment of the individual phases as well as the interfacial region. The phase behavior of fluids in constraint geometries have been studied through several techniques. High-Field Nuclear Magnetic Resonance (HF-NMR) can be used to detect fluid phases, i.e. gas, liquid, or supercritical fluid, in the bulk or under confinement. In solution-state HF-NMR, each phase exhibits a distinct chemical shift that correlates to the phase density. In turn, the emergence of multimodal in NMR spectra reveals the coexistence of multiple phases in fluid systems. Our results for ethane show that HF-NMR can enable tracking phase changes in the bulk, but also in macro-scale (10–100's μm in pore size) porous systems at various pressure and temperature conditions, even when the system us out of equilibrium. Finally, these results creates potential opportunities to investigate phase changes influenced by confinement in porous systems, though additional steps are necessary.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Multiscale petrophysical characterization and flow unit classification of the Minnelusa eolian sandstones

Integration of petrophysical and geological information is critical to simulation of subsurface carbon storage (GCS). In this sense, two depositional facies were identified from the core description and well-log interpretation, namely massive (MS) and cross-bedded (CB) facies groups. Additionally, pore-scale characteristics were studied by a combination of techniques, e.g. Nuclear Magnetic Resonance (NMR) and mercury intrusion capillary pressure (MICP). Scanning electron microscope (SEM) and petrographic analyses show that the pore structure is dominantly controlled by the depositional environment and dolomite cementation. NMR-T 2 distributions of MS and CB facies show triple and quadruple modes, respectively. In addition, MICP of high- and low-permeability MS facies samples, and their CB facies group mixtures were collected. The MS sample pore-throat size distribution is uni-modal, while the triple-modal characteristic of the mixtures indicates heterogeneous pore structures at the sub-core scale for CB facies. The reliably estimates of porosity and permeability for both facies groups via NMR techniques and the MLR (Multiple Linear Regression) approach demonstrate the applicability of these techniques to eolian sandstone. Moreover, irreducible water saturation via the T 2 -cutoff method correlates strongly with T 2LM instead of porosity. Finally, the rock quality index and flow zone indicator were calculated based on Combinable Magnetic Resonance (CMR) log interpretations. This provides direct connection to properties measured in the well. Four flow units were classified for both facies groups. Finally, results show that better reservoir quality with significant heterogeneities is observed in the CB facies. This study highlights the importance integrating multiscale petrophysical properties including facies, pore architecture and diagenesis analysis with core- to log-scale property characterization. The results herein validate our reservoir characterization and flow unit classification in eolian reservoirs.

58 GEOSCIENCES↗
DOE OSTI2021

Influence of interfacial responses of Berea Sandstone in low-salinity waterflooding environments

Wetting conditions and fluid-fluid interfacial properties are essential to understanding oil recovery in the context of low-salinity and smart waterflooding. Many have deemed wettability alteration to be the dominant interaction, while some highlight the importance of fluid-fluid interactions. In some rock-fluid systems, benefits from the use of additives can arise to favor hydrocarbon production. Understanding the balance between the fluid-fluid and rock-fluid interactions when utilizing additives is crucial to evaluate benefits in improved efficiency. Ultimately, this understanding will shed light on recovery mechanisms. Regarding oil recovery, previous studies indicate that the injection of a naphthenic acid (NA) blend dissolved in an injection brine improves oil recovery in Berea Sandstone, particularly under low-salinity conditions. Interfacial rheology results for the brine-oil interface correlated well with the recovery response. This observation was speculated to serve as a potential improved recovery mechanism through oil-trapping suppression. However, the said studies did not evaluate potentially concurrent rock wettability alteration during recovery or the initial wetting condition. The purpose of this work is to determine the production behavior in systems with NAs, namely NA-10 (3-Cyclohexanepropinoic acid), NA-14 (Cyclopentane carboxylic acid), NA-18 (Cyclohexane carboxylic acid), and NA-mix (Naphthenic acid mixture), at different initial wetting conditions under spontaneous imbibition. In addition, we tested the NAs ability to alter wettability in Berea Sandstone and determine each “additive’s” capacity to improve recovery. Here, time-domain nuclear magnetic resonance (TD-NMR), contact angle, and Amott cell tests, i.e. spontaneous imbibition, were used to analyze the influence of the selected naphthenic acids on oil displacement under different initial wetting conditions. Our results indicate that individual naphthenic acids indeed have potential as additives in low-salinity waterflooding for oil-wet systems while negatively impacting recovery in water-wet systems. However, results suggest that the evolution of the interfacial properties and wettability conditions are equally important on the recovery behavior.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Unveiling stimulation fluid-driven alterations in shale pore architecture through combined interpretation of TD-NMR and multi-component gas adsorption

The hydraulic fracturing stimulation process can alter petrophysical and flow properties of the shale matrix in unconventional reservoirs. These alterations can result from interactions with native and exogenous fluids, and can be detrimental to reservoir productivity. Different experimental procedures have been proposed to study reactive processes and thereby understand the aforementioned interactions. Most published works do not consider the rock initial saturation with formation fluid, or the effect of organic matter (OM). To gain insights into these effects, two reactive experimental sets, differing in experimental conditions, were conducted. In the first set, at 125°C and 45 MPa, a stimulation fluid surrogate was put in contact with Baxter Shale samples, previously saturated and equilibrated with synthetic formation fluid. A baseline consisted of exposure to formation fluid exclusively. In the second set, at 0.08 MPa and 25°C, contact with stimulation fluid took place as in the first set. Two additional assays in this second set either skipped the initial formation fluid saturation or removed the OM, respectively. Petrophysical properties analyses, focused on the pore architecture, relied on the combined interpretation of gas adsorption and Time-Domain Nuclear Magnetic Resonance (TD-NMR). Results show that the presence of the formation fluid significantly restricts pore space accessibility to the stimulation fluid and mitigates the pore-architecture alteration to the macro-pore region. Mineral dissolution and precipitation dominate over surface or wettability alteration. Next, results suggest that the OM restricts accessibility to some pores. Ultimately, the equilibration process with synthetic formation fluid drives mainly surface alteration, unhindered by OM.

58 GEOSCIENCES↗
DOE OSTI2021

Effect of CO 2 -brine-rock reactions on pore architecture and permeability in dolostone: Implications for CO 2 storage and EOR

Geologic carbon sequestration (GCS) is considered a feasible technology for storing substantive volumes of greenhouse gases in subsurface geological formations. In the reservoir, far from carbon dioxide (CO 2 ) injection wells or in post-injection scenarios, diffusion dominates over advection. This condition conjoins with spatially distributed geochemical reactions to induce heterogeneous changes in pore architecture, i.e. pore body and throat sizes or surface roughness. These changes can affect CO 2 transport properties and storage capacity. In this work, we investigated mineral dissolution and precipitation in dolomite samples saturated with a CO 2 -saturated brine at 93 °C and 34.5 MPa, aged without flow. Two rock types samples, i.e. intergranular- and vuggy-dominant, were selected to investigate changes in pore size, porosity and permeability under reactive conditions. Mineral dissolution and precipitation were characterized using scanning electron microscopy. Changes in pore size were quantified via time-domain nuclear magnetic resonance (TD-NMR) transverse relaxation time (T 2 ) and diffusion coefficient (D) distributions. We show that mineral dissolution likely occurs in highly permeable pathways. These observations are confirmed through analysis of (T 2 ) and diffusion coefficient (D) distributions. In contrast to results during CO 2 -enriched brine continuous injection, mineral precipitation was observed in micropores. The leftward shift of the T 2 peaks, corresponding to micropores, also evidenced mineral precipitation in lowpermeability zones. However, microscale alterations resulted only in a subtle increase in porosity and permeability. Results in this study shed light on effects of geochemical reactions on alteration of rock properties in diffusion-dominated regions during CO 2 storage.

58 GEOSCIENCES↗
DOE OSTI2021

Geochemical reactions and alteration of pore architecture in saturated shale after injection of stimulation fluid

Pore architecture regulates fluid flow between unconventional shale reservoir and hydraulically-induced fractures. Imbibition of stimulation fluid may change this architecture and alter hydrocarbon flow. Hydrothermal experiments were conducted at reservoir conditions (125 °C, 45 MPa) to test two hypotheses: 1) Shale, not stimulation fluid, dominates the geochemistry of an unconventional reservoir containing formation water; and 2) Mineral dissolution and precipitation induced by stimulation fluid is transient and manifests across micro-, meso-, and macro-scales of pore architecture. Experiments replicated a shut-in well in the Cretaceous Baxter Shale, Green River Basin, Wyoming USA. Stimulation fluid was injected into one experiment after formation water (I = 0.35 mol/kg, pH = 6.4) and core reacted for 48 days. This novel approach equilibrated rock and formation water and saturated pores with formation water before introducing stimulation fluid. The second experiment served as a control. Trends of aqueous calcium, silica and aluminum in the injection experiment suggest transient dissolution of calcite and feldspar and/or quartz as well as clay and barite precipitation; mineralogic evidence was limited to calcite dissolution and barite precipitation. The rock maintained reducing conditions (Eh = +0.08 to -0.16 V) despite injection of oxidizing stimulation fluid (Eh = 1.1 V). pH of the stimulation fluid-formation water mixture evolved from 2.3 to pre-injection values (~6) within 24 h. The results indicate that mineral dissolution and precipitation manifest in macropores with barely detectable alteration to micro- and mesopores. Formation water or organic matter in pores may have inhibited access of stimulation fluid to micro- and mesopores

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Impact of sub-core scale heterogeneity on CO2/brine multiphase flow for geological carbon storage in the Minnelusa sandstone

CO2 geological storage in deep saline aquifers is a mitigation option for CO2 emissions due to its large storage capacity and immediate accessibility. Accurately determining the CO2-brine relative permeability curves is key to the evaluation of CO2 injectivity and sweep efficiency in reservoir simulation as well as the CO2 injection in the field. This study highlights the remarkable effects of sub-core scale heterogeneity on the CO2-brine multiphase flow properties of the Minnelusa Sandstone in Wyoming. Two unsteady state CO2-brine drainage experiments were performed on the two samples. The first sample exhibits slanted laminated structure, while the second one represents a more homogeneous sandstone system. The CO2 saturation distributions during drainage reveals that the main variation in multiphase flow properties of two core samples were attributed to the porosity distribution that leads to the capillary pressure heterogeneity. Assisted history matching was used to obtain the respective relative permeability curves, which suggests heterogeneity-dependent behavior. In addition, sensitive and uncertainty analyses indicate that physical and petro-physical properties of low-porosity and low-permeability bedding layers exert marked effects on CO2 front breakthrough time and brine production. The results presented in this study help to gain insight into the CO2-brine multiphase flow properties in heterogeneous sandstones and can pave the way for the upscaling of CO2 migration and field-scale simulation accurately. This work is funded under the Department of Energy CarbonSAFE program (awards DE-FE0031624 DE0031891).

Kou, Zuhao↗
DOE OSTI2020

Analysis of ZTE MRI application to sandstone and carbonate

Micro-tomography (μCT) and nuclear magnetic resonance (NMR) have been used to characterize porous media for decades. Here, Magnetic Resonance Imaging (MRI) enables direct visualization of pore architecture and many pulse sequences exist. In this work, we tested the MRI pulse sequence Zero Echo Time (ZTE) to study sandstone and carbonate for its ability to address short relaxation times. We aimed at resolving two fluid conduit scales, i.e. pores and fractures. In this research, we study tighter porous systems than those previously reported using ZTE. Additionally, Pore Cluster Analysis (PCA), combined with ZTE, can be used to analyze pore-fracture connectivity of relatively large core plugs. We show that ZTE can resolve two-scale pore systems simultaneously, i.e. fractures and pores. By combining Time-Domain NMR pore-size analysis and PCA, we show that careful selection of resolution is necessary to understand transport in porous media.

02 PETROLEUM↗
DOE OSTI2020

Link Between CO 2 –Induced Wettability and Pore Architecture Alteration

Changes in pore (throat) size, surface roughness and mineralogy induced by supercritical-CO 2 -water-rock reactions impact petrophysical properties such as porosity, permeability, and especially wettability. Herein, we show that these changes directly impact relative permeability and capillary pressure curves, a fact rarely studied in the literature. In this work, we show that CO 2 contact angle changes emerge after Madison Limestone samples were soaked for 400 hours in CO 2 -enriched brine. Coreflooding results show that the water production rate and cumulative water production increased after the rock was exposed to carbonic acid. Moreover, the mercury capillary pressure decreased in meso- and macro-pores, indicating the increase of size in these pores due to reactions. This compounded wettability and pore network alteration can directly affect CO 2 injectivity, migration and storage capacity. Furthermore, this fundamental insight into CO 2 geological storage processes should aid practitioners to reduce uncertainties in forecasting CO 2 distribution via injection simulation.

58 GEOSCIENCES↗
DOE OSTI2020

A generalized power-law criterion for rocks based on Mohr failure theory

Nonlinearity of Mohr envelopes confirmed by past laboratory test data can be of considerable importance in theoretical interpretation of rock strength behaviors and many practical applications. Current nonlinear failure criteria are introduced with parameters to empirically fit test data, and the physical and mechanical meanings of these fitting parameters are often not known. Predicted strengths by theoretical criteria (e.g., Griffith criterion) generally do not agree well with test data. Considering the nonlinear properties of a Mohr envelope, a nonlinear failure criterion in a generalized power-law form is derived in this paper based on strength magnitude coefficient (a) and failure envelope curvature coefficient (n) which are expressed in terms of uniaxial tensile strength, uniaxial compressive strength, and angle of internal friction. Test data on granite, marble, dolomite, and andesite from published literature were chosen to test the performance of the proposed criterion along with Griffith and Hoek-Brown criteria. Statistical analysis was performed to evaluate the application of different criteria in predicting the strength of rocks. In addition, some Griffith-typed criteria are mathematically shown to be the special cases of the proposed criterion. The proposed and Hoek-Brown criteria have similar power-law forms with a significant difference in the coefficient functions that govern the shear strength magnitude of rock. The different tensile and compressive failure mechanisms are also investigated from the perspective of the relationship between the uniaxial tension Mohr circle and the proposed failure envelope.

58 GEOSCIENCES↗
DOE OSTI2020

Time-Domain Nuclear Magnetic Resonance Determination of Wettability Alteration: Analysis for Low-Salinity Water

Wettability has been shown to influence oil recovery. This property has become central to low-salinity (LSW) and smart (SWF) water flooding recovery mechanisms research. The challenge lies in the fact that oil recovery results from the combined effects of solid-liquid and liquid-liquid interactions. This demands methods that allow an independent interpretation of wettability alteration contributions. The primary objective of this work is to assess changes in wettability through the application of Time-Domain Nuclear Magnetic Resonance (TD-NMR) T 2 distribution and diffusion coefficient, starting with a well-controlled porous system, that is, glass beads, and then a model rock (Berea), in the presence of one phase, either oil or brine exclusively. Subsequently, two-phase fluid saturation was tested. For the glass beads, dimethyldichlorosilane was used to induce a hydrophobic response, as confirmed by contact angle experiments on slides of the same material. Sodium sulfate was used for its known positive influence on oil recovery during LSW and SWF. In cases where alteration of surface properties was expected, a leftward shift of the average T 2 distribution curve modes, accompanied by a reduction on the diffusion coefficient during the aging process was observed. The results of this work confirm that fluid-solid interactions during LSW and SWF, namely a shift in wettability, take place after the injection of low-salinity water.

42 ENGINEERING↗