Search NASA⌕ Search

Engineering topics

Alvarez-Salazar, Oscar

Publications and source records attributed to Alvarez-Salazar, Oscar.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Microthruster-Based Control for Precision Pointing of Next-Generation Space Telescopes

The next generation of space telescopes, such as the Habitable Exoplanet Observatory mission concept (HabEx), are expected to have milli-arcsecond-level pointing requirements at the spacecraft level. The pointing performance of such telescopes tends to be driven by internal rather than external disturbances, in particular reaction wheel jitter. This paper considers an architecture that relies on microthrusters instead of reaction wheels for spacecraft fine pointing, focusing on the HabEx mission concept as a case study. The proposed implementation uses micro-Newton-class colloidal thrusters that were tested in orbit as part of the ST7 payload on the LISA Pathfinder mission to reach Technical Readiness Level (TRL) 7. Key characteristics of these thrusters and the associated system trade-offs are first discussed. The resulting pointing control loop design is then described. Its ability to meet applicable pointing requirements is shown using three-degree-of-freedom simulations, where relevant disturbances are modelled. The control system is shown to reduce the pointing error by several orders of magnitude in about two hours, starting from coarse reaction control system (RCS) handover conditions. Once settled, the system meets the steady-state milli-arcsecond-level performance requirements with significant margin. Overall, the results show that microthruster-based pointing control architectures offer a promising alternative to traditional reaction-wheel-based designs for space telescope applications.

Ziemer, John↗
NASA NTRS2006

Automatic Alignment of Displacement-Measuring Interferometer

A control system strives to maintain the correct alignment of a laser beam in an interferometer dedicated to measuring the displacement or distance between two fiducial corner-cube reflectors. The correct alignment of the laser beam is parallel to the line between the corner points of the corner-cube reflectors: Any deviation from parallelism changes the length of the optical path between the reflectors, thereby introducing a displacement or distance measurement error. On the basis of the geometrical optics of corner-cube reflectors, the length of the optical path can be shown to be L = L(sub 0)cos theta, where L(sub 0) is the distance between the corner points and theta is the misalignment angle. Therefore, the measurement error is given by DeltaL = L(sub 0)(cos theta - 1). In the usual case in which the misalignment is small, this error can be approximated as DeltaL approximately equal to -L(sub 0)theta sup 2/2. The control system (see figure) is implemented partly in hardware and partly in software. The control system includes three piezoelectric actuators for rapid, fine adjustment of the direction of the laser beam. The voltages applied to the piezoelectric actuators include components designed to scan the beam in a circular pattern so that the beam traces out a narrow cone (60 microradians wide in the initial application) about the direction in which it is nominally aimed. This scan is performed at a frequency (2.5 Hz in the initial application) well below the resonance frequency of any vibration of the interferometer. The laser beam makes a round trip to both corner-cube reflectors and then interferes with the launched beam. The interference is detected on a photodiode. The length of the optical path is measured by a heterodyne technique: A 100- kHz frequency shift between the launched beam and a reference beam imposes, on the detected signal, an interferometric phase shift proportional to the length of the optical path. A phase meter comprising analog filters and specialized digital circuitry converts the phase shift to an indication of displacement, generating a digital signal proportional to the path length.

Halverson, Peter↗
NASA NTRS2004

Terrestrial Planet Finder cryogenic delay line development

Delay lines provide the path-length compensation that makes the measurement of interference fringes possible. When used for nulling interferometry, the delay line must control path-lengths so that the null is stable and controlled throughout the measurement. We report on a low noise, low disturbance, and high bandwidth optical delay line capable of meeting the TPF interferometer optical path length control requirements at cryogenic temperatures.

cryogenic↗
NASA NTRS2004

Kite: Status of the External Metrology Testbed for SIM

Kite is a system level testbed for the External Metrology system of the Space Interferometry Mission (SIM). The External Metrology System is used to track the fiducial that are located at the centers of the interferometer's siderostats. The relative changes in their positions needs to be tracked to tens of picometers in order to correct for thermal measurements, the Kite testbed was build to test both the metrology gauges and out ability to optically model the system at these levels. The Kite testbed is an over-constraint system where 6 lengths are measured, but only 5 are needed to determine the system. The agreement in the over-constrained length needs to be on the order of 140 pm for the SIM Wide-Angle observing scenario and 8 pm for the Narrow-Angle observing scenario. We demonstrate that we have met the Wide-Angle goal with our current setup. For the Narrow-Angle case, we have only reached the goal for on-axis observations. We describe the testbed improvements that have been made since our initial results, and outline the future Kite changes that will add further effects that SIM faces in order to make the testbed more SIM like.

metrology↗