Capillary Wave Dynamics of Thin Polymer Films over Submerged Nanostructures
Not Available
Engineering topics
Publications and source records attributed to Alvine, Kyle J.
Not Available
Thin films of Al on lead zirconate titanate (PZT) annealed in high-pressure hydrogen at 100C exhibit surface Pb nanowire growth. Wire diameter is approximately 80 nm and length can exceed 100 microns. Based on microstructural analysis using electron microscopy and ion scattering, a vapor-solid scheme with hydrogen as a carrier gas was proposed as a growth mechanism. We expect that these observations may lead to controlled Pb nanowires growth through pattering of the Al film.
Hydrogen is known to damage or degrade piezoelectric materials, at low pressure for ferroelectric random access memory applications, and at high pressure for hydrogen powered vehicle applications. The piezoelectric degradation is in part governed by the motion of hydrogen species within the piezoelectric materials. We present here Quasi-Elastic Neutron Scattering (QENS) measurements of the local hydrogen species motion within lead zirconate titanate (PZT) and barium titanate (BTO) on samples charged by gaseous exposure to high-pressure gaseous hydrogen {approx}17 MPa. Filter Analyzed Neutron Spectroscopy (FANS) studies of the hydrogen enhanced vibrational modes are presented as well. Results are discussed in context of theoretically predicted interstitial hydrogen lattice sites and compared to comparable bulk diffusion studies of hydrogen diffusion in lead zirconate titanate.
Abstract: Hydrogen is being considered as a next-generation clean burning fuel. However, hydrogen has well known materials issues, including blistering and embrittlement in metals. Piezoelectric materials are used as actuators in hydrogen fuel technology. We present studies of materials compatibility of piezoelectric films in a high pressure hydrogen environment. Absorption of high pressure hydrogen was studied with Elastic Recoil Detection Analysis (ERDA) and Rutherford Back Scattering (RBS) in lead zirconate titanate (PZT) and barium titanate (BTO) thin films. Hydrogen surface degradation in the form of blistering and Pb mixing was also observed.
Nanostructures created in polymer films by nanoimprint lithography are subject to large stresses, both those from the imprinting processes as well as stresses arising from the intrinsic thermodynamic instabilities. These stresses can induce nanostructure deformation that can compromise the intended function of the imprinted pattern. Controlling these stresses, and thus the stability of the imprinted patterns, is a key scientific issue for this technology. The requirement of film stability against dewetting requires the use of entangled polymer films, which necessitates an understanding of complex viscoelastic response of these materials to large stresses. Here we investigate the evolution of the surface topography of nanoimprinted patterns in polystyrene films through a high throughput annealing approach in which the patterns are annealed for a fixed time on a controlled temperature gradient. Using principles of time-temperature superposition we systematically explore the effect of varying basic system variables such as pattern feature size, polymer molecular mass, imprinting temperature, on nanopattern stability and on the evolution of imprinted patterns driven by surface tension and internal stress. Nanostructure collapse generally occurs through a combination of a "slumping" instability, where the imprinted film simply relaxes towards a planar film and the film height decreases with time, and a lateral "zigzag" instability in the nanoimprinted lines.
Optical lithography deep in the UV spectrum is the predominate route for high-resolution, high-volume nanoscale pattering. However, state-of-the-art optical lithography tools are exceedingly expensive and this places serious limitations on the applications, technical sectors, and markets where highresolution patterning can be implemented. To date the only substantial market for high-end optical lithography tools has been semiconductor fabrication. Nanoimprint lithography (NIL) has recently emerged as an alternative to optical lithography and combines the potential of sub-fi ve-nanometer patterning resolution with the low cost and simplicity of a stamping process. [ 1–4 ] This has led to signifi cant efforts to implement NIL methods, not only for semiconductor logic devices, but also in fi elds as diverse as the direct patterning of interlayer dielectrics (ILDs) for back-end-of-line (BEOL) interconnect structures, [ 5–7 ] bitpatterned magnetic media for data storage, [ 8 , 9 ] and high-brightness light-emitting diodes (LEDs). [ 10 ] Some of these are new areas where nanoscale patterning has previously not been considered, and are made possible here by the low cost and simplicity of the NIL stamping processes.
Surface forces play a paramount role in most aspects of Nanoimprint Lithography. In particular, subjecting nanoimprinted patterns to moderate heating allows surface tension to smooth out undesirable roughness and defects in the patterns, but this thermal reflow treatment can induce structural decay or even collapse of the patterns by capillary instability if this process is not carefully controlled. Adhesion between the mold and polymer film can also cause the imprinted structure to tear or fracture. Fluorinated surfactants (FS) are attractive for reducing mold adhesion, yet the effects of these additives on nanostructure stability during thermal reflow are not well understood. Here we present thermal stability studies of line-space grating patterns created by Thermal Embossing Nanoimprint Lithography (TENIL) on model polystyrene (PS) films with FS additives. As expected by energy considerations, FS segregates to the air interface where it seems to facilitate mold release. This also reduces the surface energy and thus reduces the driving force for pattern "slumping" (height decay). However, the beneficial effects of the surfactant are counterbalanced by the fact that the FS decreases the effective film viscosity, which accelerates nanopattern leveling. The net effect is that the pattern height decay is strongly a function of FS concentration. This enhanced film fluidity in the presence of FS also makes the pattern more susceptible to an undulatory capillary instability under thermal reflow conditions. Surface phase segregation of FS and PS is also observed in conjunction with both slumping and lateral capillary instabilities, which may be useful for producing chemically patterned surfaces.
Capillary forces play an active role in defining the equilibrium structure of nanoscale structures. This effect can be especially pronounced in soft materials such as polymers near or above their glass transition temperature Tg where material flow is possible. In these situations, the effect of surface tension can produce varied and complex capillary instabilities, even in relatively simple geometries such as parallel line-space grating patterns. Here we investigate a novel capillary instability that arises in polystyrene line-space gratings with a residual layer connecting these structures (created by nanoimprint lithography) upon thermal annealing of these patterns. This novel instability is characterized by the development of lateral undulations of the lines that culminates in the local coalescence of adjacent imprinted lines. An exact analytic model of this undulatory instability is not possible, but we introduce a simple physical model for this lateral instability based on the driving force to reduce the surface energy, as in the well-known Rayleigh-Plateau instability which is likewise surface energy driven. Good agreement is obtained between this simplified model and our observations. Our insights into the nature of this instability have implications for controlling the thermal stability of nanoscale patterns made by nanoimprint lithography or other lithography techniques.
Monolayers of bimodal gold nanoparticles on silicon are investigated by a combination of microscopy (dry monolayers) and x-ray diffraction (dry and wet monolayers). In the presence of an excess of small particles, the nanoscale packing structure closely resembles the small-particle-rich scenario of the structural crossover transition that has been predicted and also observed with micron-scale hard-sphere colloids. Structural morphology is monitored in situ during monolayer dissolution and reassembly within the thin liquid wetting film. This approach allows investigation of size and solvent effects on nanoparticles in quasi-two-dimensional confinement.