Search NASA⌕ Search

Engineering topics

Alyssa Manis

Publications and source records attributed to Alyssa Manis.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

NASA Orbital Debris Radar Measurements by the Haystack Ultra-wideband Satellite Imaging Radar (HUSIR)

For many years, the NASA Orbital Debris Program Office (ODPO) has partnered with the U.S. Department of Defense and the Massachusetts Institute of Technology Lincoln Laboratory (MIT/LL) to collect data on the orbital debris environment using the Haystack radar. These measurements are used to characterize the small debris environment in low Earth orbit (LEO), down to a noise-limited size of approximately 5 mm—depending on altitude. The Haystack radar operated by MIT/LL underwent upgrades starting in May 2010, with operations resuming in 2014 as the Haystack Ultra-wideband Satellite Imaging Radar (HUSIR). HUSIR is the primary source of data used by the ODPO to statistically sample orbital debris in the 5-mm to 10-cm size regime in LEO and is a key source of data to build and validate the NASA Orbital Debris Engineering Model. In this presentation, we will present recent HUSIR results and show how NASA uses them to understand the orbital debris environment.

Mark Matney↗
NASA NTRS2023

Optimizing Altitude Sampling and Sensitivity with the Goldstone Orbital Debris Radar

The NASA Orbital Debris Program Office (ODPO) has used the Goldstone Orbital Debris Radar (Goldstone) since 1993 to characterize orbital debris (OD) in low Earth orbit too small to be tracked by the U.S. Space Surveillance Network. Operated by NASA’s Jet Propulsion Laboratory, Goldstone can measure OD as small as 3 mm at 1000 km altitude and lower. Goldstone is a bistatic radar that for 25 years used Deep Space Station (DSS)-14 as a transmitter and DSS-15 as a receiver. In early 2018, DSS-15 was decommissioned and replaced with DSS-25 (and occasionally DSS-26) of the Deep Space Network Apollo Cluster. The increased baseline between DSS-14 and DSS-25 significantly reduced the instantaneous altitude coverage of the bistatic beam overlap. Initial measurements in 2018 were focused around 800 km, which has approximately the highest flux of sub-centimeter debris. In 2019, DSS-14 was offline for maintenance, and the ODPO designed an annual survey observation plan to efficiently sample altitudes from 700 km to 1000 km, since many NASA satellites fly in this range. This paper discusses the observation plan, including the development of the pointings, a refinement of the altitudes of interest, and an analysis of the effects of random pointing errors on beam overlap. Additionally, results from measurements taken in 2020 and 2021 are presented, showing that not only is the observation plan effective at sampling 700 km to 1000 km altitude, but it is also producing the most sensitive terrestrial radar measurements at these altitudes to date.

James Murray↗
NASA NTRS2023

NASA Orbital Debris Engineering Model ORDEM 3.2 – Software User Guide

This National Aeronautics and Space Administration (NASA) Orbital Debris Engineering Model (ORDEM) 3.2 Software User Guide accompanies delivery of the latest upgraded version of the model, ORDEM 3.2. The user guide also provides a top-level program description and a list of capabilities. It includes descriptions of runtime error and information codes, input/output file formats, runtimes for different orbit configurations, and how to use uncertainty files. ORDEM 3.2 supersedes the previous NASA Orbital Debris Program Office (ODPO) models – ORDEM 3.0 (Stansbery, et al. 2014) and ORDEM2000 (Liou, et al. 2002). The availability of new sensor and in situ data, re-analysis of older data, and development of new analytical techniques has enabled the construction of this more comprehensive and sophisticated model. An upgraded graphical user interface (GUI) is integrated with the software. This upgraded GUI uses project-oriented organization and provides the user with graphical representations of numerous output data products. For example, these range from the conventional flux vs. average debris size (or altitude bin) for chosen analysis orbits (or views) to the more complex color-contoured, two-dimensional (2-D) directional flux diagrams in local spacecraft elevation and azimuth. The current model, ORDEM 3.2, supports spacecraft as well as telescope/radar project assessments. ORDEM 3.2 contains updated debris populations covering low Earth orbit (LEO, up to 2000 km altitude) to geosynchronous orbit (GEO, up to 40,000 km altitude) and can assess debris calculations up to year 2050, extending coverage past the previous limit of 2035 in ORDEM 3.0. Although populations differ from its predecessor, ORDEM 3.2 is functionally the same as ORDEM 3.0 and can support ORDEM 3.0 projects through backward compatibility.

Andrew Vavrin↗
NASA NTRS2023

Orbital Debris Shape Effect Investigations for Mitigating Risk

NASA’s Orbital Debris Program Office (ODPO) and Hypervelocity Impact Technology (HVIT) team have coordinated to better understand the risks to upper stages and spacecraft from non-spherical orbital debris. It is well understood that fragmentation (collision or explosion) events in orbit produce fragments of various materials, sizes, and shapes. To further characterize these parameters, the ODPO is developing the next-generation Orbital Debris Engineering Model (ORDEM) version 4.0 to include orbital debris shape distributions. Ground-based assets, such as radar and optical sensors, can provide size estimates and some insight into material based on radar return or optical filter photometry/spectroscopy, respectively. Characterizing an object’s shape requires more laboratory analyses to infer how shape affects these measurements. More importantly, in addition to size and material/density, the shape of fragments in orbit will alter the ballistic limit equations used in orbital debris risk assessments with NASA’s Bumper Code. The ODPO plans to release ORDEM 4.0 in the coming years. Performing ground-based laboratory impact tests on high-fidelity spacecraft mockups provides the means to directly measure size, mass, material/density, and shape of fragments, all key parameters needed to characterize real-world break up events. The DebriSat test, the results of which are provided, showcases the details of this type of experiment. The goal of this collaborative research between the ODPO and the HVIT team is to include a shape parameter in the environmental and breakup models used to assess risk for various space structures. This paper examines ground-based laboratory impact tests and the associated fragment shape categories. Provided these defined shapes, the approach is simplified by assuming a right circular cylinder (RCC) approximation with varying length-to-diameter ratios. Highlights of impact tests conducted by the HVIT team using non-spherical projectiles based on the RCC approximation are presented. Hydrocode simulations have also been performed to expand on the complexity of variations with non-spherical projectiles. Lastly, ray-tracing simulations of various RCCs of known material are provided to support the ongoing research on optical reflectance distributions with known shapes and to highlight how this may modify the current optical size estimation model. The status and plan forward are outlined for NASA's orbital debris shape effect investigation using a multidisciplinary approach by the ODPO and the HVIT team.

Heather Cowardin↗
NASA NTRS2022

NASA Orbital Debris Engineering Model (ORDEM) 3.1: Model Verification and Validation

The NASA Orbital Debris Engineering Model (ORDEM) 3.1 Model Verification and Validation (V&V) document accompanies the delivery of the latest ORDEM 3.1 model (Vavrin & Manis, 2019) and provides a detailed description of the V&V activities used to verify that the model was built correctly and validate the model against independent, real world sources of data obtained from sampling the orbital debris environment. This ORDEM 3.1 Model V&V document, along with the related ORDEM 3.1 Model Process document – which covers details of the mathematical, statistical, and physical basis of the model – are intended to inform credibility assessments, risk analyses, uncertainty characterizations, and other applications derived from use of the model by the ORDEM 3.1 user community.

Timothy Kennedy↗
NASA NTRSDate not supplied

Flux Comparison of Master-8 and Ordem 3.1 Modelled Space Debris Population

With ESA’s Meteoroid And Space debris Terrestrial Environment Reference (MASTER-8) model and NASA’s Orbital Debris Engineering Model(ORDEM) 3.1, the two premier orbital debris engineering models have been officially released. The two models come with significant enhancements and now represent state-of-the-art orbital debris modelling for their respective agencies. Both models provide the community with estimates of the space debris environment from low Earth orbit (LEO) up to at least geostationary altitude. The MASTER population is an event-based simulation of all known events that generate debris and objects that are part of the U.S. Space Surveillance Network (SSN) catalog, which provides coverage of objects with diameters down to approximately 10cm in LEO and 1 m in geosynchronous Earth orbit (GEO). Different models are used to simulate the artificial objects and their orbit evolution over time. These models are called “sources” since they assign an origin to each individual object and consist of fragments, solid rocket motor (SRM) remainders, sodium-potassium(NaK) droplets, paintflakes, ejecta, and multi-layer insulation (MLI) fragments. The objects from each source are characterized by having individual release mechanisms, as well as orbital distributions, material composition, size, and mass distributions. Dedicated radar and telescope observation data is used to calibrate the model for objects larger than 1 cm in LEO and larger than 10 cm in GEO. For calibrating the small-sized objects, below 1 cm, impact data from returned surfaces are analyzed. Because the >1cm object population is dominated by fragments, the fragmentation event database was updated to include new events, as well as re-evaluate past events. Special attention was drawn to re-evaluating theFengyun-1C anti-satellite test from 2007 and Cosmos-Iridium collision event from 2009 since these events shape the fragment population because of their severity. After 2009, the two largest fragmentations in terms of number of tracked debris are the Briz-M explosion in 2012 and the NOAA-16explosion in 2015. In total, there are 261 confirmed fragmentations in the database up to November 2016.The baseline population for ORDEM 3.1 is based on the U.S. SSN catalog, and observational datasets from radar, in situ, and optical sources provide a foundation from which the model populations are statistically extrapolated to smaller size regions. These regions are not well-covered by the SSN catalog yet may pose the greatest threat to operational spacecraft. The NASA Standard Satellite Breakup Model is used to generate fragments greater than 1mm from collisions and explosions, and these fragment populations are scaled using ground-based radar data. Specific major debris-producing events, including the Fengyun-1C, Iridium 33, and Cosmos2251 debris clouds, and unique populations, such as NaK droplets, were re-examined, modelled, and added to the ORDEM environment separately. Optical measurement data is used to model the GEO population down to 10 cm. The debris environment is propagated using NASA’s LEO-to-GEO Environment Debris model, and future explosions of intact objects and collisions involving objects greater than 10 cm are assessed statistically. The environment from a few millimetres down to 10 𝜇m is modelled using a special degradation model where small particles are generated from intact spacecraft and rocket bodies, then the populations are scaled to fit in situ cratering data from Space Shuttle returned surfaces. Fragments smaller than 10 cm are differentiated based on material density categories, i.e., high-, medium-, and low-density, to better characterize the potential debris risk posed to upper stages and spacecraft. This paper will discuss the MASTER and ORDEM approaches for modelling populations and compare fluxes for specific orbits, including sun-synchronous, ISS-altitude, geosynchronous transfer, and GEO. In the end, a conclusion is drawn towards the importance of having multiple fundamentally different, yet validated, models to estimate the space debris population.

Andre Horstmann↗
NASA NTRSDate not supplied

Flux Comparison of Master-8 And Ordem 3.1 Modelled Space Debris Population

In this paper, the modelled debris fluxes by ESA’s Meteoroid And Space debris Terrestrial Environment Reference (MASTER-8) model and NASA’s Orbital Debris Engineering Model (ORDEM) 3.1 are compared. At first, the basic modelling approaches for both models are presented to explain the fundamentally different model philosophies and help the reader to comprehend and interpret the obtained results. Then, the flux results of both models for three different orbits are presented and analysed. They are discussed and set into perspective. A conclusion is drawn at the end of the paper, highlighting the ongoing cooperation of both agencies responsible for their models.

Andre Horstmann↗
NASA NTRSDate not supplied

Updates on the Debrisat Hypervelocity Experiment and Characterization of Fragments in Support of Environmental Models

To develop, maintain, and update orbital debris environmental and break-up models, such as the NASA Orbital Debris Engineering Model (ORDEM) and the NASA Standard Satellite Breakup Model (SSBM), the NASA Orbital Debris Program Office (ODPO) relies on the most recent validated datasets from various measurement sources, both laboratory and environmental. One key project that will provide insight for break-up events using modern-day spacecraft materials and construction techniques is the DebriSat laboratory hypervelocity-impact test. Based on the mass of the target, the projectile, and the impact velocity, the expected number of fragments greater than 2 mm, generated using the NASA SSBM, was estimated to be close to 85,000. To date, the DebriSat fragment database continues to grow, with over 200,000 fragments collected that will help inform updates to the SSBM. Additionally, the growing fragment ensemble will support key parameters for the next release of NASA’s environmental models, employing fragment shapes, densities, and size distributions. To further support these environmental models, specifically the size parameter used in ground-based optical measurements, optical characterization on a subset of DebriSat fragments is being conducted in ODPO’s Optical Measurement Center (OMC). Broadband bidirectional reflectance distribution (BRDF) measurements will provide insight into the optical-based NASA Size Estimation Model (OSEM). The OSEM equates an object’s brightness to size (e.g., diameter of a disk or sphere) given several assumed parameters, including a defined phase function, albedo, and range. To address the first defined parameter, the ODPO has been using ray-tracing software to simulate light conditions in the OMC and to generate phase functions (i.e., specular, Lambertian, and experimentally-derived) of known shapes, materials, and sizes. This simulated data, in addition to the experimentally derived measurements collected in the OMC, will aid in determining whether a new phase function would be suitable for an updated OSEM. The OSEM also assumes a single-value albedo, thus pre-impact spectral measurements on a subset of DebriSat materials were acquired for baseline material characterization and to provide insight into spacecraft material taxonomies. This DebriSat spectral data, along with spectral measurements from other known spacecraft material samples, will allow for better analyses of albedo variations and the effect on size calculations of defined laboratory targets, thus further supporting OSEM updates. This paper provides an overview of DebriSat, the status of the project, updates on the parameter distributions, an overview of the NASA SSBM, and ongoing fragment characterization efforts within the OMC.

Heather Cowardin↗
NASA NTRSDate not supplied

Updates on the DebriSat Hypervelocity Experiment and Characterization of Fragments in Support of Environmental Models

To develop, maintain, and update orbital debris environmental and break-up models, such as the NASA Orbital Debris Engineering Model (ORDEM) and the NASA Standard Satellite Breakup Model (SSBM), the NASA Orbital Debris Program Office (ODPO) relies on the most recent validated datasets from various measurement sources, both laboratory and environmental. One key project that will provide insight for break-up events using modern-day spacecraft materials and construction techniques is the DebriSat laboratory hypervelocity-impact test. Based on the mass of the target, the projectile, and the impact velocity, the expected number of fragments greater than 2 mm, generated using the NASA SSBM, was estimated to be close to 85,000. To date, the DebriSat fragment database continues to grow, with over 200,000 fragments collected that will help inform updates to the SSBM. Additionally, the growing fragment ensemble will support key parameters for the next release of NASA’s environmental models, employing fragment shapes, densities, and size distributions. To further support these environmental models, specifically the size parameter used in ground-based optical measurements, optical characterization on a subset of DebriSat fragments is being conducted in ODPO’s Optical Measurement Center (OMC). Broadband bidirectional reflectance distribution (BRDF) measurements will provide insight into the optical-based NASA Size Estimation Model (OSEM). The OSEM equates an object’s brightness to size (e.g., diameter of a disk or sphere) given several assumed parameters, including a defined phase function, albedo, and range. To address the first defined parameter, the ODPO has been using ray-tracing software to simulate light conditions in the OMC and to generate phase functions (i.e., specular, Lambertian, and experimentally-derived) of known shapes, materials, and sizes. This simulated data, in addition to the experimentally derived measurements collected in the OMC, will aid in determining whether a new phase function would be suitable for an updated OSEM. The OSEM also assumes a single-value albedo, thus preimpact spectral measurements on a subset of DebriSat materials were acquired for baseline material characterization and to provide insight into spacecraft material taxonomies. This DebriSat spectral data, along with spectral measurements from other known spacecraft material samples, will allow for better analyses of albedo variations and the effect on size calculations of defined laboratory targets, thus further supporting OSEM updates. This paper provides an overview of DebriSat, the status of the project, updates on the parameter distributions, an overview of the NASA SSBM, and ongoing fragment characterization efforts within the OMC.

Heather Cowardin↗
NASA NTRSDate not supplied

Optimizing Altitude Sampling and Sensitivity with the Goldstone Orbital Debris Radar

The NASA Orbital Debris Program Office (ODPO) has used the Goldstone Orbital Debris Radar (Goldstone) since 1993 to characterize orbital debris (OD) in low Earth orbit too small to be tracked by the U.S. Space Surveillance Network. Operated by NASA’s Jet Propulsion Laboratory, Goldstone can measure OD as small as 3 mm at 1000 km altitude and lower. Goldstone is a bistatic radar that for 25 years used Deep Space Station (DSS)-14 as a transmitter and DSS-15 as a receiver. In early 2018, DSS-15 was decommissioned and replaced with DSS-25 (and occasionally DSS-26) of the Deep Space Network Apollo Cluster. The increased baseline between DSS-14 and DSS-25 significantly reduced the instantaneous altitude coverage of the bistatic beam overlap. Initial measurements in 2018 were focused around 800 km, which has approximately the highest flux of sub-centimeter debris. In 2019, DSS-14 was offline for maintenance, and the ODPO designed an annual survey observation plan to efficiently sample altitudes from 700 km to 1000 km, since many NASA satellites fly in this range. This paper discusses the observation plan, including the development of the pointings, a refinement of the altitudes of interest, and an analysis of the effects of random pointing errors on beam overlap. Additionally, results from measurements taken in 2020 and 2021 are presented, showing that not only is the observation plan effective at sampling 700 km to 1000 km altitude, but it is also producing the most sensitive terrestrial radar measurements at these altitudes to date.

James Murray↗
NASA NTRSDate not supplied

An Overview of Ground-Based Radar and Optical Measurements Utilized By the Nasa Orbital Debris Program Office

For over 30 years, the NASA Orbital Debris Program Office (ODPO) has led the characterization of orbital debris (OD) too small to be tracked by the U.S. Space Surveillance Network (SSN), yet which may pose the greatest threat to human spaceflight and robotic missions. Measurements from specialized sensors, including ground-based radars and telescopes capable of detecting smaller objects, provide the foundation for developing statistical models to describe the current state and future evolution of the OD environment from low Earth orbit (LEO) to geosynchronous Earth orbit (GEO). Since 1990, the ODPO has partnered with the U.S. Department of Defense and the Massachusetts Institute of Technology Lincoln Laboratory (MIT/LL) to collect data using the Haystack Ultrawideband Satellite Imaging Radar (HUSIR) – formerly Haystack – to characterize OD in LEO with a sensitivity of approximately 5 mm at 1000 km altitude. In addition, since 1993, the Goldstone Orbital Debris Radar, operated by NASA’s Jet Propulsion Laboratory, has provided data on OD as small as approximately 2-3 mm for altitudes below 1000 km, some of the most sensitive ground-based measurements achievable at these altitudes. Recently, collaborations with the 18 th Space Control Squadron of the U.S. Space Force have also provided the ODPO with special datasets from the Space Fence to extend coverage below the historical SSN limit of 10 cm and to characterize individual breakup events in LEO. For GEO altitudes, the Eugene Stansbery Meter Class Autonomous Telescope (ES-MCAT), a joint NASA-Air Force Research Laboratory project that reached full operational capability in 2021, collects data on debris smaller than 1 m and provides coverage of debris in historically under-sampled high-altitude orbital regimes. This paper summarizes the radar and optical sensors utilized by the ODPO, their unique capabilities, and recent datasets and applications for statistical sampling of the dynamic OD environment.

Alyssa Manis↗
NASA NTRSDate not supplied

Radar Measurements of Orbital Debris from the Haystack Ultra-wideband Satellite Imaging Radar (HUSIR): 2020 to 2022

For over three decades, the NASA Orbital Debris Program Office (ODPO) has partnered with the U.S. Department of Defense and the Massachusetts Institute of Technology’s Lincoln Laboratory (MIT/LL) to collect radar data on the orbital debris (OD) environment. These radar measurements are used to statistically measure cm and sub-cm debris in low Earth orbit (LEO) that is used to define the current debris environment, monitor how the environment evolves, and support predictions of the future debris environment. Currently, the principal ground-based radar sensor used by the ODPO is the MIT/LL Haystack Ultrawideband Satellite Imaging Radar (HUSIR). HUSIR provides data on OD down to approximately 5 mm in size at altitudes below 1000 km. This paper will deliver an overview of recent HUSIR measurements of the LEO debris environment for calendar years 2020 to 2022. Process improvements will be highlighted along with results of interest, including the effects of the 15 November 2021 Russian direct ascent anti-satellite (ASAT) test on the defunct COSMOS 1408 spacecraft.

Jessica A. Arnold↗
NASA NTRSDate not supplied

An Overview of NASA’s Newest Engineering Model, ORDEM 4.0

Since the mid-1990s, one of the most important products produced by the NASA Orbital Debris Program Office (ODPO) has been the Orbital Debris Engineering Model (ORDEM). This series of models distills down our knowledge of the orbital debris environment to compute debris fluxes on satellites in a given orbit. This information can be used by spacecraft and upper stage designers and operators to design missions for better protection against the debris environment. The current version of the model is ORDEM 3.2, but the ODPO is working on the next generation of ORDEM, to be designated ORDEM 4.0. ORDEM 4.0 will include many known features from previous models, such as the ability to input a spacecraft orbit and time and to compute the flux as a function of debris size, impact speed, impact direction, and debris material densities, as well as uncertainty information on the flux. ORDEM 4.0 will update debris populations using the most recent measurements, including radar observations by the Haystack Ultrawideband Satellite Imaging Radar (HUSIR), NASA’s Goldstone radar, data from the new Space Surveillance Network Space Fence, and observations of Geosynchronous Earth Orbits (GEO) using the Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT). The latest in situ impact data from returned hardware surfaces will be used. In addition, ORDEM 4.0 will introduce a parameterized debris shape model based on laboratory hypervelocity impact tests, such as DebriSat. This will allow analysts to implement shape characteristics in their damage equations and more accurately predict impact damage risk by debris of different shapes and orientations. This paper provides an overview of some of the new features forthcoming in ORDEM 4.0 and a status report on its development.

Mark Matney↗
NASA NTRSDate not supplied

The Completion of a Geosynchronous Earth Orbit Survey with the Eugene Stansbery-Meter Class Autonomous Telescope

The Eugene Stansbery-Meter Class Autonomous Telescope (ES-MCAT) is the primary optical sensor used by the NASA Orbital Debris Program Office (ODPO) to statistically characterize the geosynchronous Earth orbit (GEO) debris environment and support future Orbital Debris Engineering Model (ORDEM) releases. The ES-MCAT completed its first optical survey of the GEO region from 2020 to 2022. The primary goal of this survey was to autonomously collect and process GEO data with calculated photometric and astrometric uncertainties. A pointing plan was developed to provide uniform sampling within the region of interest (ROI) while accounting for predicted downtime due to insufficient observing conditions. Detections are autonomously correlated to the Space Surveillance Network (SSN) catalog to determine if objects are correlated targets (CTs) or uncorrelated targets (UCTs), the latter of which are of interest for modeling the GEO orbital debris environment. To assess the size detection sensitivity over time and monitor the general performance of the telescope’s optics and software, the optical throughput of the system and limiting magnitudes are evaluated on a routine basis. While the telescope’s ability to operate autonomously and remotely allowed for the GEO survey to continue throughout the COVID-19 pandemic, travel restrictions hampered routine cleaning of the optics during this time, and the primary mirror degraded enough to require recoating. The mirror was removed in 2022, concluding the first GEO survey. The primary mirror received a new coating designed to be more robust against the harsh environment surrounding the ES-MCAT’s location on Ascension Island, accounting for experience gained during operations over the first GEO survey. In early 2023, the recoated primary mirror was reinstalled, and the second GEO survey was initiated. The primary goal of the second GEO survey is to characterize the evolving GEO debris environment with updated optics, software, and pointing strategies while allowing for the inclusion of non-GEO regimes or those that are outside of the ROI. While the pointing method implemented in the first survey allowed for adequate coverage of the ROI over two years, it has been improved to include pointings that avoid the Moon’s position and the galactic plane to reduce software processing time and maximize the detection capabilities of fainter objects. This method also accounts for the changing weather patterns throughout the year and reduces coverage gaps in the ROI. Provided the success of the first two-year GEO survey using autonomous operations, the ODPO is actively collaborating with the United States Space Force (USSF) to make the ES-MCAT a contributing sensor to the SSN. This paper presents results from the first GEO survey including magnitude distributions and orbital parameters for CTs and UCTs. Details are provided for the automated processing pipeline and the optical system throughput for the previous and current primary mirror coatings. In addition, an updated strategy for the second GEO survey to optimize coverage over the ROI is discussed, as are preliminary results from the ongoing second survey.

Corbin Cruz↗