Search NASA⌕ Search

Engineering topics

Amanda Chou

Publications and source records attributed to Amanda Chou.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

A Summary of the 2023 Joint High-Speed Boundary Layer Transition Workshop

A joint workshop between the Air Force Office of Scientific Research, the Office of Naval Research, and the NASA Hypersonic Technology Project was held in June 2023 on the topic of high-speed boundary-layer transition. The purpose of this workshop was to gather subject matter experts in the areas of supersonic and hypersonic boundary-layer transition in the areas of geometries of interest, computational methods, facilities and diagnostics, flight experiments, flow control, and new approaches and to discuss the current state of the art in the field. As gaps and accomplishments were identified, roadmaps were also created to guide future investments in these areas. The top recommendations are (1) to define relevant common geometries of interest that can be worked by multiple research groups; (2) improve modeling of high-enthalpy flows involving chemistry and ablation, studies of receptivity of freestream disturbances and atmospheric particulates into the boundary layer, surface feature characterization and modeling of changes to geometry; (3) design and determine viable flow control methods; and (4) move towards incorporating boundary layer transition prediction into a standard practice for design of high-speed vehicles. To execute this last recommendation successfully, investments beyond fundamental (basic and early applied) research are needed.

boundary layer transition↗
NASA NTRS2024

Transitional Flow in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

Prediction of roughness-induced transition is a practical requirement for the optimized design of high-speed vehicles, which rely on a reduction of thermal stresses and drag for higher performance. This reduction is affected by boundary layer transition, which on real vehicles may be caused by unavoidable roughness such as inherent surface material roughness and deterioration or roughness in the form of sensing elements, fasteners, etc. A better understanding of transition resulting from roughness can help inform acceptable manufacturing tolerances or maintenance requirements on real vehicles.

Amanda Chou↗
NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS2022

Instabilities in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

A roughness patch defined by a two-dimensional Fourier series was installed in a highly-polished flat plate model immersed in a supersonic quiet flow. The NASA Langley Research Center Supersonic Low Disturbance Tunnel is capable of providing a Mach 3.5 flow with low freestream acoustic noise and low turbulence levels. Measurements made with a hot-wire probe downstream of the roughness element showed the presence of instability modes that did not cause transition in the measurement region at a freestream unit Reynolds number of Re =12.6×10^6/m. The largest amplitude mode appeared to be similar to a symmetric mode. The same roughness patch immersed in a higher freestream acoustic noise environment showed little to no evidence of the instability modes. Instead, disturbances found in the boundary layer matched closely to the freestream spectra measured in the empty tunnel under the same conditions, indicating some evidence of freestream forcing in the boundary layer.

Roughness induced transition↗
NASA NTRS2021

Boundary-layer Instability Measurements on a Cone at Freestream Mach 3.5

An experimental study was conducted in the NASA (National Aeronautics and Space Administration) Langley Supersonic Low-Disturbance Tunnel to investigate naturally-occurring instabilities in a supersonic boundary layer on a 7◦ half-angle cone at nominal freestream conditions: Mach 3.5, total temperature of 299.8K, and unit Reynolds numbers (millions per m) of 9.89, 13.85, 21.77, and 25.73. Instability measurements were acquired under noisy-flow and quiet-flow conditions. Pitot-pressure and calibrated hot-wire measurements were obtained using a model-integrated traverse system to document the model flow field. In noisy-flow conditions, growth rates and mode shapes achieved good agreement between the measured results and linear stability theory (LST). The corresponding N factor at transition from LST is N ≈ 3.9. Under quiet-flow conditions, the most unstable first-mode instabilities as predicted by LST were measured, but this mode was not the dominant instability measured in the boundary layer. Instead, the dominant instabilities were less-amplified, low-frequency disturbances predicted by LST, and grew according to linear theory. These low-frequency unstable disturbances were initiated by freestream acoustic disturbances through a receptivity process believed to occur near the branch I location of the cone. Under quiet-flow conditions, the boundary layer remained laminar up to the last measurement station for the largest unit Reynolds number, implying a transition N factor of N > 8.5.

Boundary Layer↗
NASA NTRS2021

Simultaneous Focused Laser Differential Interferometry and High-Speed Schlieren in a Mach 6 Flow

An instrument is demonstrated that is capable of simultaneous and independent flow density fluctuation measurements over the same line-of-sight by combining two optical techniques: focused laser differential interferometry (FLDI) and high-speed schlieren (HSS). The FLDI instrument measures fluctuations at a single point in the flowfield at 10 MHz, with the resulting signal most sensitive in the region nearest the focal plane of the FLDI laser beam. The HSS instrument acquires images at 20 kHz along the same optical axis as the FLDI beam, but with the resulting signal path averaged over the entire HSS line-of-sight. The introduction of the HSS optics into the FLDI beam path provides two high-quality measurement capabilities in a single system with no degradation of performance relative to stand-alone FLDI or HSS instruments.

Focused Laser Differential Interferometry↗
NASA NTRS2020

Transition induced by Streamwise Arrays of Roughness Elements on a Flat Plate in Mach 3.5 Flow

The flow behind streamwise arrays of roughness elements was examined with a hot-wire probe. The roughness elements had heights of approximately 20% and 40% of the boundary layer thickness and different spacings and orientations of these roughness elements were tested. The circular roughness elements were spaced two diameters apart or four diameters apart from center to center. Transition moved upstream only when the roughness elements were spaced four diameters apart. The rectangular roughness elements were oriented so that they were at a 45-degree angle relative to the leading edge of the plate. Tandem rectangular elements either had the same orientation or opposing orientation. Mean mass-flux and total-temperature profiles of the flow field downstream of the roughness elements were examined for mean-flow distortion. Mass-flux fluctuation profiles showed that a 45-kHz odd-mode disturbance was present downstream of the shorter circular roughness elements. The dominant instability downstream of the taller circular roughness elements was a 65–85 kHz even-mode disturbance. Mass-flux fluctuation profiles showed that the dominant mode downstream of the tandem rectangular roughness elements with the same orientation was similar to that of a single roughness element and centered at a frequency of approximately 55 kHz. The 55-kHz instability appeared to correspond to increased spanwise shear, and thus was determined to be an odd-like mode. The dominant instability downstream of the tandem roughness elements with opposing orientation was centered at a frequency of 65 kHz and did not transition in the measurement region.

Amanda Chou↗
NASA NTRSDate not supplied

Supersonic Traveling Crossflow Wave Characteristics in Ground and Flight Tests

This paper continues analysis of data acquired in a series of supersonic crossflow transition experiments on a 65° swept- wing model tested in both wind tunnel and flight. Flow visualization data are summarized to provide context for the swept-wing instability mechanisms of interest. Unsteady pressure measurements obtained near the wing model leading edge (LE) are studied using 2nd- and 3rd-order statistical methods to extract traveling crossflow wave characteristics from these data. Comparisons between tunnel and flight data with boundary-layer (BL) Linear Stability Theory (LST) predictions provide insights into BL transition phenomena similarities and differences observed in tests using the same swept-wing model configurations. Comparisons of unsteady pressure data results for wing LE configurations with and without distributed-roughness-element (DRE) patterns installed, suggest traveling crossflow disturbance growth is reduced when this type of flow control is applied. A brief stud y of different background surface roughness levels on the wing LE suggests the potential for another flow control approach to promote laminar flow on swept wings using streamwise-biased surface finishes.

Lewis R Owens↗
NASA NTRSDate not supplied

Transition Induced by an Egg-Crate Roughness on a Flat Plate in Supersonic Flow

Measurements were made in the wake of a roughness patch with a hot wire to determine mode shapes and frequencies of the dominant instabilities. The egg-crate roughness pattern is an analytic function described by a sinusoidal equation, similar to arrays of discrete elements that are positioned in a spanwise and streamwise grid, which were considered in previous computations. This is an intermediate configuration toward understanding the underlying physics of pseudorandom distributed roughness. At a freestream unit Reynolds number of10.8×106/m, the boundary layer did not transition within the measurement region. The largest amplitude boundary layer instability was centered near 53 kHz and appeared to be similar to an antisymmetric mode centered behind the region downstream of all of the peaks in the egg-crate roughness. This mode was similar to a mode found to have the highest N factor in previous computational studies. At a freestream unit Reynolds number of12.6×106/m, the boundary layer transitioned to turbulence. The dominant instability was centered near 74 kHz and grew linearly before saturating and breaking down. The mode shape of the 74-kHz mode was again an antisymmetric mode centered behind all of the peaks in the egg-crate roughness.

Amanda Chou↗
NASA NTRSDate not supplied

Measurements of Freestream Fluctuations in the Langley Research Center Unitary Plan Wind Tunnel

Measurements of the freestream disturbance environment were made in the high Machnumber leg of the NASA Langley Research Center Unitary Plan Wind Tunnel. The un-steady pitot pressure fluctuations and mass-flux fluctuations were measured with fast-response pressure transducers and hot wires, respectively. These were the first directmeasurements of the disturbance environment made in this facility’s test section. Thespectral content of the disturbances in the freestream show a significant amount of powerat frequencies below 100 Hz. At Mach 3.5 and Mach 4.6, there is also a broad peak in thespectra spanning from 100 Hz to 1 kHz. The RMS amplitude of the freestream mass-fluxfluctuations ranges from approximately 0.5% to 2.5%. The amplitude of the disturbancesincreases with Mach number but does not vary significantly with Reynolds number andstreamwise station. At Mach 2.4, the amplitude of the pitot pressure and mass-flux fluctu-ations is higher at the bottom of the tunnel than in the center of the tunnel. This increaseis likely due to the presence of a vortical structure near the bottom of the tunnel. Com-pared to similar facilities that operate in the same Mach number range, the freestreamdisturbance amplitudes follow similar trends and are within the same order of magnitude

freestream disturbance↗
NASA NTRSDate not supplied

Bluntness and Supersaturation Effects on the Second Mode Instability in Mach 10 Flow

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 31-Inch Mach 10 Tunnel to investigate the impact of nosetip radius and freestream supersaturation on the development of the second mode instability. The model was instrumented with surface-mounted Kulite® and PCB® pressure transducers and thermocouples. Power spectral density plots demonstrate the anticipated trends of the second mode instability weakening and shifting to lower frequencies with increased bluntness. Heat transfer measurements suggest laminar flow over the bulk of the model for most testing conditions, with evidence of transition by the cone base for the sharpest nosetip (R = 0.15 mm) at the higher unit Reynolds numbers. The dynamic surface pressure and heat transfer measurements show that reducing the temperature of the freestream to a supersaturated state has a significant stabilizing effect on the model boundary layer. The surface measurements are observed to be highly dependent on the level of clustering in the freestream. Significant changes in surface pressure spectra due to total temperature reduction are first noted below T0= 948 K, while more substantial fluctuation reductions are found below T0= 810 K.

Hypersonics↗
NASA NTRSDate not supplied

Instabilities in the Wake of Roughness on a Flat Plate in a Quiet Supersonic Tunnel

Roughness-induced transition is an unavoidable reality in practical high-speed vehicles. Typical prediction of transition due to roughness include algebraic correlations and, more recently, semi-empirical methods. In the NASA Langley Research Center Supersonic Low Disturbance Tunnel, a Mach 3.5 quiet tunnel, several transition experiments have been performed in the past decade to better understand the mechanisms by which small roughness causes transition in a supersonic boundary layer. The study started first with isolated roughness elements of different planforms and shapes and progressed to increasingly more complicated geometries before arriving at a pseudorandom roughness, defined by an analytic function. Concurrent computational efforts progressed with these studies as well, starting with the use of linear stability theory and progressing to the use of harmonic linearized Navier-Stokes to predict the growth of boundary layer stabilities.

Amanda Chou↗