Search NASA⌕ Search

Engineering topics

Ampomah, William

Publications and source records attributed to Ampomah, William.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

CCUS Perspectives: Assessing Historical Contexts, Current Realities, and Future Prospects

CCUS technologies are crucial solutions for mitigating climate change by reducing CO2 emissions from industrial operations and energy sectors. This review critically examines the current state of CCUS technologies, and highlights advancements, challenges, regulatory frameworks, and future directions. It comprehensively analyzes carbon capture methods, such as pre-combustion, post-combustion, and oxy-fuel combustion capture, while comparing their efficiencies and limitations. The review also explores carbon utilization techniques, such as direct and indirect utilization, emphasizing their potential applications and technological constraints. Additionally, it assesses various carbon storage methods, focusing on geological, ocean, and mineralization storage, and discusses their capacity, feasibility, and environmental implications. The study reviews the policy and regulatory frameworks, economic viability, market trends, and environmental sustainability of CCUS. By identifying research gaps and recommending future research priorities, this review aims to guide the development of more efficient/effective, and cost-effective CCUS technology, ensuring their role in a sustaining low-carbon future. This review provides a forward-looking perspective, a critical and interdisciplinary analysis that assesses the current state of CCUS technologies, and further provides a roadmap for future development.

Energy & Fuels↗
DOE OSTI2024

Mechanisms of Waterflood Inefficiency: Analysis of Geological, Petrophysical and Reservoir History, a Field Case Study of FWU (East Section)

The petroleum reservoir represents a complex heterogeneous system that requires thorough characterization prior to the implementation of any incremental recovery technique. One of the most commonly utilized and successful secondary recovery techniques is waterflooding. However, a lack of sufficient investigation into the inherent behavior and characteristics of the reservoir formation in situ can result in failure or suboptimal performance of waterflood operations. Therefore, a comprehensive understanding of the geological history, static and dynamic reservoir characteristics, and petrophysical data is essential for analyzing the mechanisms and causes of waterflood inefficiency and failure. In this study, waterflood inefficiency was observed in the Morrow B reservoir located in the Farnsworth Unit, situated in the northwestern shelf of the Anadarko Basin, Texas. To assess the potential mechanisms behind the inefficiency of waterflooding in the east half, geological, petrophysical, and reservoir engineering data, along with historical information, were integrated, reviewed, and analyzed. The integration and analysis of these datasets revealed that several factors contributed to the waterflood inefficiency. Firstly, the presence of abundant dispersed authigenic clays within the reservoir, worsened by low reservoir quality and high heterogeneity, led to unfavorable conditions for waterflood operations. The use of freshwater for flooding exacerbated the adverse effects of sensitive and migratory clays, further hampering the effectiveness of the waterflood. In addition to these factors, several reservoir engineering issues played a significant role in the inefficiency of waterflooding. These issues included inadequate perforation strategies due to the absence of detailed hydraulic flow units (HFUs) and rock typing, random placement of injectors, and uncontrolled injected fresh water. These external controlling parameters further contributed to the overall inefficiencies observed during waterflood operations in the east half of the reservoir. A detailed understanding of the mechanistic factors of inefficient waterflood operation will provide adequate insights into the development of the improved recovery technique for the field.

Morgan, Anthony (ORCID:0000000211519153)↗
DOE OSTI2023

Time-lapse VSP integration and calibration of subsurface stress field utilizing machine learning approaches: A case study of the morrow B formation, FWU

This study aims to develop a methodology for calibrating subsurface stress changes through time-lapse vertical seismic profiling (VSP) integration. The selected study site is a region around the injector well located within Farnsworth field unit (FWU), where there is an ongoing CO 2 -enhanced oil recovery (EOR) operation. In our study, a site-specific rock physics model was created from extensive geological, geophysical, and geomechanical characterization through 3D seismic data, well logs, and core assessed as part of the 1D MEM conducted on the characterization well within the study area. Here, the Biot-Gassmann workflow was utilized to combine the rock physics and reservoir simulation outputs to determine the seismic velocity change due to fluid substitution. Modeled seismic velocities attributed to mean effective stress were determined from the geomechanical simulation outputs, and the stress-velocity relationship developed from ultrasonic seismic velocity measurements. A machine learning-assisted workflow comprised of an artificial neural network and a particle swarm optimizer (PSO) was utilized to minimize a penalty function created between the modeled seismic velocities and the observed time-lapse VSP dataset. The successful execution of this workflow has affirmed the suitability of acoustic time-lapse measurements for 4D-VSP geomechanical stress calibration pending measurable stress sensitivities within the anticipated effective stress changes and the availability of suitable and reliable datasets for petroelastic modeling. © 2023 Society of Chemical Industry and John Wiley & Sons, Ltd.

58 GEOSCIENCES↗
DOE OSTI2023

Coupled Hydromechanical Modeling and Assessment of Induced Seismicity at FWU: Utilizing Time-Lapse VSP and Microseismic Data

The objective of this work is to utilize integrated geomechanics, field vertical seismic profile (VSP) and microseismic data to characterize the complex subsurface stress conditions at the Farnsworth Unit (FWU). The model is based on a five-spot sector model extracted from a primary geomechanical model. The five-spot well injection pattern is characterized by extensive reservoir characterization data, such well logs, extracted cores and borehole geophone data, to facilitate the detailed examination of stress changes and microseismic event occurrences. The study utilizes field vertical seismic volumes acquired from the injection well 13-10A. The seismic volumes successfully provided snapshots of the behavior of the reservoir at distinct times. The use of VSP and microseismic data provided direct and indirect estimates of the dynamic stress changes occurring in the overburden, reservoir and underburden rock formations. In order to illuminate the stress regions and identify rocks that have undergone inelastic failure, microseismic event occurrences were utilized. Microseismic activity has been detected at the FWU; further study of its locations, timing, and magnitude was needed to deduce the nature of the changing stress state. The results of the study revealed that microseismic events were successfully modeled within the Morrow B formation. Moment magnitudes of seismic events were within the same magnitudes for events in the reservoir, suggesting the suitability of the model. The results of the study showed that the computed moment magnitudes for seismic events were insignificant to warrant safety concerns. The study findings showed the usefulness of coupled hydromechanical models in predicting the subsurface stress changes associated with CO 2 injection. The knowledge gained from this study will serve as a guideline for industries planning to undertake underground CO 2 storage, and characterize the subsurface stress changes.

02 PETROLEUM↗
DOE OSTI2023

Microseismic Monitoring at the Farnsworth CO 2 -EOR Field

The Farnsworth Unit in northern Texas is a field site for studying geologic carbon storage during enhanced oil recovery (EOR) using CO 2 . Microseismic monitoring is essential for risk assessment by detecting fluid leakage and fractures. We analyzed borehole microseismic data acquired during CO 2 injection and migration, including data denoising, event detection, event location, magnitude estimation, moment tensor inversion, and stress field inversion. We detected and located two shallow clusters, which occurred during increasing injection pressure. The two shallow clusters were also featured by large b values and tensile cracking moment tensors that are obtained based on a newly developed moment tensor inversion method using single-borehole data. The inverted stress fields at the two clusters showed large deviations from the regional stress field. The results provide evidence for microseismic responses to CO 2 /fluid injection and migration.

02 PETROLEUM↗
DOE OSTI2023

Seismic Monitoring at the Farnsworth CO2-EOR Field Using Time-Lapse Elastic-Waveform Inversion of 3D-3C VSP Data

During the Development Phase of the U.S. Southwest Regional Partnership on Carbon Sequestration, supercritical CO2 was continuously injected into the deep oil-bearing Morrow B formation of the Farnsworth Unit in Texas for Enhanced Oil Recovery (EOR). The project injected approximately 94 kilotons of CO2 to study geologic carbon storage during CO2-EOR. A three-dimensional (3D) surface seismic dataset was acquired in 2013 to characterize the subsurface structures of the Farnsworth site. Following this data acquisition, the baseline and three time-lapse three-dimensional three-component (3D-3C) vertical seismic profiling (VSP) data were acquired at a narrower surface area surrounding the CO2 injection and oil/gas production wells between 2014 and 2017 for monitoring CO2 injection and migration. With these VSP datasets, we inverted for subsurface velocity models to quantitatively monitor the CO2 plume within the Morrow B formation. We first built 1D initial P-wave (Vp) and S-wave (Vs) velocity models by upscaling the sonic logs. We improved the deep region of the Vp and Vs models by incorporating the deep part of a migration velocity model derived from the 3D surface seismic data. We improved the shallow region of 3D Vp and Vs models using 3D traveltime tomography of first arrivals of VSP downgoing waves. We further improved the 3D baseline velocity models using elastic-waveform inversion (EWI) of the 3D baseline VSP upgoing data. Our advanced EWI method employs alternative tomographic and conventional gradients and total-variation-based regularization to ensure the high-fidelity updates of the 3D baseline Vp and Vs models. We then sequentially applied our 3D EWI method to the three time-lapse datasets to invert for spatiotemporal changes of Vp and Vs in the reservoir. Our inversion results reveal the volumetric changes of the time-lapse Vp and Vs models and show the evolution of the CO2 plume from the CO2 injection well to the oil/gas production wells.

42 ENGINEERING↗
DOE OSTI2023

Improving Subsurface Stress Characterization for Carbon Dioxide Storage Projects by Incorporating Machine Learning Techniques

The overall objective of this project is to develop a framework for reliable characterization and prediction of the state of stress in the overburden and underburden (including the basement) in CO 2 storage reservoirs using machine learning and integrated geomechanics and geophysical methods. Specifically, we propose to develop workflow encompassing of technologies and/or methods to predict stress and pressure changes due to CO 2 injection in an active tertiary recovery site and their impacts on subtle fault activation, fractures and occurrence of microseismic events and compare responses to field observations. In this project, we anticipate using dataset from the Farnsworth field Unit (FWU) which is operated by Purdure Petroleum. A novel elastic-waveform VSP inversion technique will be used to estimate high-resolution spatial and temporal changes of elastic moduli in CO 2 storage reservoirs, which will be combined with velocity-stress relationship derived from laboratory tests to obtain subsurface pressure and stress. Clustered microseismic data will be jointly inverted for improved focal mechanisms. Least-squares reverse-time migration of microseismic waveform data will be performed to directly image fracture/fault zones. Additionally, a deep neural network machine learning technique with convolutional and recurrent layers will be used for learning the spectro-temporal structures in microseismic waveforms. The results of this geotechnical data analysis will be integrated to develop a high-resolution 3D mechanical earth model extending from the overburden sealing formations to the underburden including the basement. Mechanical properties will be derived through integration of mechanical logs, tests, available results from chemo-mechanical laboratory tests, and elastic inversion of seismic data using a combination of Bayesian and stochastic methods as well as machine learning technique. Failure features (faults/fractures) will be represented and/or modeled based on seismic and core data analysis. A transient hydrodynamic-geomechanical model will be developed through coupling with the calibrated FWU reservoir simulation model. The full physics coupled model will be used to train a reduced order proxy model using machine learning algorithm for estimating stress which will then be used with appropriate constitutive relationships and forward seismological models to simulate pressure changes and induced microseismicity. An advanced optimization framework will be developed to perform a history match to minimize error between field observations and simulated. The history matched proxy model will be verified against the full-physics equivalent. The field observations that will be used in the coupled model calibration process include pressure/stress inverted from VSP, moment magnitude from microseismic analysis, real time downhole pressure measurements, production and injection data. Parameter sensitivity and uncertainty analysis will be performed to characterize the impact of model parameter uncertainty on stress estimates. The proposed project will have significant impact on future field implementation of the proposed technology. Because the project field site is an ongoing CO 2 EOR development, the value of the new technology will be demonstrated in an operational context and evaluated as a viable risk mitigation strategy. Cost/benefit will be evaluated together with the various commercial incentives for CO 2 sequestration available to oil and gas operators. The extensive available dataset and ongoing data acquisition under the SWP Phase III work plan provides flexibility for investigation of multiple approaches and reduces technical risk.

58 GEOSCIENCES↗
DOE OSTI2023

Techno-economic life cycle assessment of CO 2 -EOR operations towards net negative emissions at farnsworth field unit

Optimizations of CO 2 Water Alternating Gas(WAG)- systems with multi-objectives of incremental recovery and maximization of CO 2 storage are challenging. Here, the incorporation of a total Greenhouse gas (GHG) life cycle assessment is mostly ignored leading to inaccurate estimation of overall net carbon emissions of their operations. In this study, the effect of a total GHG life cycle assessment on a multi-objective CO 2 -WAG optimization with integrated techno-economic assessment (TEA) which factors carbon tax credit is conducted. A life cycle assessment (LCA) was conducted utilizing a 20 -year optimized post history matched data from a high fidelity reservoir simulation model. Using data generated from the optimum result, a techno-economic life cycle analysis was further conducted. The first scenario classified as the base model had an estimated 81% of purchased CO 2 sequestered. The results through a comprehensive techno-economic LCA model yielded a net estimate of 73% of purchased CO 2 . The optimized forecasted model which considered key operational and reservoir factors such as WAG ratio, injection rates and periods, and well specification resulted in an improved sequestration of 92% of purchased CO 2 . However, this also dropped to 84% after taking it through LCA. These results clearly indicate a significant amount of net CO 2 is not accounted for when operations are not analyzed through LCA. From the LCA, direct flaring volumes of CO 2 , energy consumption and efficiency of unit equipment were noticed to be the major causes of these reductions. Considering ten main sources of energy as source of energy generation, a comparative techno-eco LCA was conducted. The results confirmed a lower net volume and NPV for energy sources with higher carbon footprints and vice versa. Thus, a total LCA of CO 2 -WAG greatly influences net storage factor of purchased CO 2 and hence project NPV where tax credit/incentives per ton of CO 2 sequestered is considered. Although operational conditions are optimized for best results, there are significant factors that leads to minimization of net storage factor. This study therefore provides an insightful information for optimizing CO 2 -WAG multi-objectives to achieve minimum GHG emission.

02 PETROLEUM↗
DOE OSTI2022

Simulation study of chemo-mechanical impacts of CO 2 injection in morrow b sandstone reservoir

Here, this study investigates the impacts of geomechanical and geochemical changes on carbon storage in a partially depleted oil reservoir, using results from four different coupled simulation models. Models were used to examine the relative importance of storage mechanisms, and how changing reservoir parameters might affect these mechanisms through time. The study uses data from a Morrowan sandstone reservoir in the Farnsworth Unit (FWU), Ochiltree County, Texas which is currently undergoing CO 2 enhanced oil recovery (EOR). Partially depleted oil reservoirs such as the FWU offer attractive carbon utilization and/or storage targets because of existing infrastructure and economic benefits from incremental oil recovery as well as tax credits. However, prediction of storage capacity or long-term fluid migration in these fields can be difficult because of the wide variation in formation fluids and operational histories that may have undergone. CO 2 injection can cause complex geomechanical and geochemical responses in a reservoir as a result of interplay between dynamic changes in pore pressure, reservoir temperature, fluid composition, and interactions between formation fluids, CO 2 , and reservoir rock. Thus, multiple coupled numerical simulation models must be developed and used to more precisely understand what CO 2 storage mechanisms are most significant, as well as the long-term fate of the stored CO 2 . Our study used results from hydrodynamic, coupled hydro-geomechanical, coupled hydro-geochemical, and coupled hydro-geomechanical-geochemical models to examine how changes in geomechanical and geochemical properties can impact the injectivity or storage capacity of CO 2 . Models simulated historical field operations and then forward-modeled a water-alternate-gas (WAG) operation for 20 years, followed by a 1000-year post-injection monitoring. The work demonstrates that in this specific reservoir, geomechanical impacts appear to be more significant than any geochemical processes, which showed minimal impact on reservoir properties. Furthermore, these simulation scenarios corroborated other studies showing more than 90% of CO 2 injected are being stored and will remain stored in the reservoir. The study was able to draw on a rich set of data from this currently operational project for the work. Because the Morrow is a widespread oil-bearing reservoir in the midcontinent of the United States and is fairly typical of many sandstone reservoirs elsewhere, the study has significance beyond the boundaries of our field area.

58 GEOSCIENCES↗
DOE OSTI2022

Quantitative interpretation of time-lapse seismic data at Farnsworth field unit: Rock physics modeling, and calibration of simulated time-lapse velocity responses

Here, this study investigates the contribution of fluid saturation variation to the time-lapse velocity response by performing fluid substitution modeling. The methodology is exemplified by the time-lapse seismic monitoring of carbon dioxide at Farnsworth field unit (FWU). In order to evaluate the fluid distribution in a matured oil reservoir, the Southwest Regional Partnership (SWP) acquired multiple vertical seismic profile (VSP) surveys at different times during the CO 2 –water alternatinggas (WAG) injection period. In this work, we present a thorough methodology for computing the elastic response of the saturated rock for different fluid saturations using a site-specific petro-elastic model (PEM). The output from the PEM was combined with results from a fluid compositional model to compute the seismic velocities at times corresponding to each VSP survey. To produce a calibrated simulated response, the measured time-lapse seismic velocities were integrated into the numerical simulation model. The mismatches between the predicted and measured time-lapse velocities were minimized through an iterative calibration process using a trained artificial neural network proxy (ANN) coupled with a particle swarm optimizer (PSO). Our study indicates that the hybrid optimization workflow can effectively perform the history matching. With an accurate prediction of the hydrodynamic properties, the migration of CO 2 within the subsurface was modeled by predicting the spatial velocity distribution for a radius of 305 m around the injection well. The technology demonstrated and the expertise gained from this study can guide similar CO 2 -WAG projects.

58 GEOSCIENCES↗
DOE OSTI2022

Assessment of chemo-mechanical impacts of CO 2 sequestration on the caprock formation in Farnsworth oil field, Texas

This study evaluates the chemo-mechanical influence of injected CO 2 on the Morrow B sandstone reservoir and the upper Morrow shale caprock utilizing data from the inverted 5-spot pattern centered on Well 13-10A within the Farnsworth unit (FWU). This study also seeks to evaluate the integrity of the caprock and the long-term CO 2 storage capability of the FWU. The inverted 5-spot pattern was extracted from the field-scale model and tuned with the available field observed data before the modeling work. Two coupled numerical simulation models were utilized to continue the study. First, a coupled hydro-geochemical model was constructed to simulate the dissolution and precipitation of formation minerals by modeling three intra-aqueous and six mineral reactions. In addition, a coupled hydro-geomechanical model was constructed and employed to study the effects of stress changes on the caprock’s porosity, permeability, and ground displacement. The Mohr–Coulomb circle and failure envelope were used to determine caprock failure. In this work, the CO 2 -WAG injection is followed by the historical field-observed strategy. During the forecasting period, a Water Alternating Gas (WAG) injection ratio of 1:3 was utilized with a baseline bottom-hole pressure constraint of 5500 psi for 20 years. A post-injection period of 1000 years was simulated to monitor the CO 2 plume and its effects on the CO 2 storage reservoir and caprock integrity. The simulation results indicated that the impacts of the geochemical reactions on the porosity of the caprock were insignificant as it experienced a decrease of about 0.0003% at the end of the 1000-year post-injection monitoring. On the other hand, the maximum stress-induced porosity change was about a 1.4% increase, resulting in about 4% in permeability change. It was estimated that about 3.3% of the sequestered CO 2 in the formation interacted with the caprock. Despite these petrophysical property alterations and CO 2 interactions in the caprock, the caprock still maintained its elastic properties and was determined to be far from its failure.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2022

Optimization of Water-Alternating-CO2 Injection Field Operations Using a Machine-Learning-Assisted Workflow

Summary This paper will present a robust workflow to address multiobjective optimization (MOO) of carbon dioxide (CO2)-enhanced oil recovery (EOR)-sequestration projects with a large number of operational control parameters. Farnsworth unit (FWU) field, a mature oil reservoir undergoing CO2 alternating water injection (CO2-WAG) EOR, will be used as a field case to validate the proposed optimization protocol. The expected outcome of this work would be a repository of Pareto-optimal solutions of multiple objective functions, including oil recovery, carbon storage volume, and project economics. FWU’s numerical model is used to demonstrate the proposed optimization workflow. Because using MOO requires computationally intensive procedures, machine-learning-based proxies are introduced to substitute for the high-fidelity model, thus reducing the total computation overhead. The vector machine regression combined with the Gaussian kernel (Gaussian-SVR) is used to construct proxies. An iterative self-adjusting process prepares the training knowledge base to develop robust proxies and minimizes computational time. The proxies’ hyperparameters will be optimally designed using Bayesian optimization to achieve better generalization performance. Trained proxies will be coupled with multiobjective particle swarm Optimization (MOPSO) protocol to construct the Pareto-front solution repository. The outcomes of this workflow will be a repository containing Pareto-optimal solutions of multiple objectives considered in the CO2-WAG project. The proposed optimization workflow will be compared with another established methodology using a multilayer neural network (MLNN) to validate its feasibility in handling MOO with a large number of parameters to control. Optimization parameters used include operational variables that might be used to control the CO2-WAG process, such as the duration of the water/gas injection period, producer bottomhole pressure (BHP) control, and water injection rate of each well included in the numerical model. It is proved that the workflow coupling Gaussian-SVR proxies and the iterative self-adjusting protocol is more computationally efficient. The MOO process is made more rapid by squeezing the size of the required training knowledge base while maintaining the high accuracy of the optimized results. The outcomes of the optimization study show promising results in successfully establishing the solution repository considering multiple objective functions. Results are also verified by validating the Pareto fronts with simulation results using obtained optimized control parameters. The outcome from this work could provide field operators an opportunity to design a CO2-WAG project using as many inputs as possible from the reservoir models. The proposed work introduces a novel concept that couples Gaussian-SVR proxies with a self-adjusting protocol to increase the computational efficiency of the proposed workflow and to guarantee the high accuracy of the obtained optimized results. More importantly, the workflow can optimize a large number of control parameters used in a complex CO2-WAG process, which greatly extends its utility in solving large-scale MOO problems in various projects with similar desired outcomes.

Energy & Fuels↗
DOE OSTI2021

Probabilistic Assessment and Uncertainty Analysis of CO2 Storage Capacity of the Morrow B Sandstone—Farnsworth Field Unit

This paper presents probabilistic methods to estimate the quantity of carbon dioxide (CO2) that can be stored in a mature oil reservoir and analyzes the uncertainties associated with the estimation. This work uses data from the Farnsworth Field Unit (FWU), Ochiltree County, Texas, which is currently undergoing a tertiary recovery process. The input parameters are determined from seismic, core, and fluid analyses. The results of the estimation of the CO2 storage capacity of the reservoir are presented with both expectation curve and log probability plot. The expectation curve provides a range of possible outcomes such as the P90, P50, and P10. The deterministic value is calculated as the statistical mean of the storage capacity. The coefficient of variation and the uncertainty index, P10/P90, is used to analyze the overall uncertainty of the estimations. A relative impact plot is developed to analyze the sensitivity of the input parameters towards the total uncertainty and compared with Monte Carlo. In comparison to the Monte Carlo method, the results are practically the same. The probabilistic technique presented in this paper can be applied in different geological settings as well as other engineering applications.

03 NATURAL GAS↗
DOE OSTI2021

Development of Time Lapse VSP Integration Workflow: A Case Study at Farnsworth CO2-EOR Project

Abstract This study aims to develop a 4D Vertical Seismic Profile (VSP) integration workflow to improve the prediction of subsurface stress changes. The selected study site is a 5-spot pattern within the ongoing CO2-EOR operations at the Farnsworth Field Unit FWU in Ochiltree County, Texas. The specific pattern has undergone extensive geological and geomechanical characterization through the acquisition of 3D seismic data, geophysical well logs, and core. This workflow constrains a numerical hydromechanical model by applying a penalty function formed between "modeled" versus "observed" time-lapse compressional and shear seismic velocity changes. Analyses of geophysical logs and ultra-sonic measurements on core exhibit measurable sensitivities to changes in both fluid saturation and mean effective stress. These data are used to develop a site-specific rock physics model and stress-velocity relationship, which inform the numerical models used to generate the "modeled" portion of the penalty function. The "observed" portion of the penalty function is provided by a novel elastic full-waveform inversion of the available 3D baseline and three monitor surveys to produce high-quality estimates of time-lapse compressional and shear seismic velocity changes. The modeling workflow accounts sequentially for fluid substitution and stress impacts. Hydrodynamic and geomechanical properties of the 3D coupled numerical model are estimated through geostatistical integration of well log and core data with 3D seismic inversion products. Changes in seismic velocities due to fluid substitution are computed using the Biot-Gassmann workflow and site-specific rock physics. Stress impacts on time-lapse seismic velocity changes are modeled from the effective stress output of the hydromechanical model and are initially based on the velocity versus effective stress relationship extracted from core mechanical testing. Based on the principle of superposition of seismic wavefields, seismic velocity changes attributed to fluid substitution and that due to changes in mean effective stress are treated as linearly additive. The modeled results are upscaled using Backus averaging to reconcile scale discrepancies between the modeled and measured datasets to formulate the penalty function. This manuscript presents the forward modeling process and concludes that for the base case, the seismic velocity changes due to mean effective stress dominates over the seismic velocity changes attributed to fluid substitution because of the extensive range of the pressure perturbations. Successful minimization of this penalty function calibrates the coupled hydrodynamic geomechanical numerical model and affirms the suitability of acoustic time-lapse measurements such as 4D-VSP for geomechanical calibration.

02 PETROLEUM↗
DOE OSTI2021

A comprehensive techno-eco-assessment of CO 2 enhanced oil recovery projects using a machine-learning assisted workflow

Carbon dioxide enhanced oil recovery (CO 2 -EOR) projects not only extract residual oil but also sequestrate CO 2 in the depleted reservoirs. Here, this study develops a machine-learning-based workflow to co-optimize the hydrocarbon recovery, CO 2 sequestration volume and project net present value (NPV) simultaneously. Considering the trade-off relationships among the objective functions, support vector regression with Gaussian kernel (Gaussian- SVR) proxies are coupled with multi-objective particle swarm optimization (PSO) protocol and generate Pareto optimal solutions. Taking advantage of the high computational efficacy of the proxy model, economic uncertainties introduced by tax credits, capital costs and oil price are investigated by this study. The results indicate that the tax incentive policy (Section 45Q) plays a vital role in enhancing the economic returns of CO 2 -EOR projects, especially under the depression of crude oil market. The proposed workflow has been successfully implemented to optimize a water alternative CO 2 (CO 2 -WAG) injection project in a depleted oil sand in the US. The optimization results yield an incremental oil production of 15.8 MM STB and 1.37 MM metric tons of CO 2 storage in a 20-year development strategy, with the highest project NPV to be 205.6 MM US dollars.

03 NATURAL GAS↗