Search NASA⌕ Search

Engineering topics

Anderson, Todd

Publications and source records attributed to Anderson, Todd.

Toward the Advanced Manufacturing of Land-Based Wind Turbine Blades

The National Renewable Energy Laboratory and General Electric (GE) are partners within the Additive and Modular-Enabled Rotor Blades and Integrated Composites Assembly (AMERICA) project. AMERICA aims to develop advanced manufacturing solutions to reduce labor and cycle time while increasing recyclability of wind turbine blades. The project is funded by the U.S. Department of Energy's Advanced Manufacturing Office. This paper describes the techno-economic and life cycle analysis of the novel manufacturing process applied to the 15-meter long tip of the blade of a representative 3.4 MW land-based wind turbine. We establish a comparison to a standard manufacturing process, highlighting challenges and opportunities. Several uncertainties affect the analysis, but we highlight an opportunity space. With the current set of assumptions, the tip adopting advanced manufacturing is predicted to lower labor by 21%, cycle time by 39%, and total blade tip costs by 15% while simultaneously increasing production quality and adopting recyclable thermoplastic resin. A life cycle analysis returns comparable metrics for climate change impact and embodied energy between the two processes.

3D printing↗

Toward the Advanced Manufacturing of Land-Based Wind Turbine Blades: Preprint

The National Renewable Energy Laboratory (NREL) and General Electric (GE) are partners within the Additive and Modular Enabled Rotor Blades and Integrated Composites Assembly (AMERICA) project. AMERICA aims to develop advanced manufacturing solutions to reduce labor and cycle time while increasing recyclability of wind turbine blades. The project is funded by the Advanced Manufacturing Office (AMO) of the U.S. Department of Energy (DOE). This paper describes the techno-economic analysis of the novel manufacturing process applied to the tip of the blade of a representative land-based wind turbine. A comparison to a standard manufacturing process is established, highlighting challenges and opportunities. Several uncertainties affect the analysis, but with the current set of assumptions, the tip adopting advanced manufacturing is predicted to lower labor by 21%, cycle time by 39%, and total blade tip costs by 15% while simultaneously increasing production quality and adopting recyclable thermoplastic resin.

3D printing↗

Genome Engineering for Materials Synthesis: Workshop Report

The Biological Systems Science Division (BSSD) within the U.S. Department of Energy’s (DOE) Office of Biological and Environmental Research (BER) funds basic research on plants and microbes relevant to several DOE bioenergy and environmental mission areas. BSSD has a long history of developing and supporting genomic, molecular, and structural characterization of biological systems. This sustained focus has led to important discoveries and increased understanding of these systems, as well as translational pathways to new processes and products. BSSD research seeks to understand the fundamental genome-encoded properties of plants and microbes that can be harnessed or redesigned for beneficial purposes. Current emphases are leading to the discovery, development, and understanding of numerous plant and microbial species with traits suitable for the production of fuels and chemicals from renewable biomass or light. Additionally, BSSD supports research leading to an understanding of the complex and essential interactions among plants, microbial communities, and the environment. The processes by which living organisms synthesize intricate and potentially valuable inorganic biomaterials are gaining increasing attention. The application of genomic, molecular, and structural tools offers great potential to better understand and potentially exploit these widespread, yet still poorly understood, genome-encoded biosynthetic processes. To engage the relevant scientific communities in discussions of this research opportunity, BER convened the Genome Engineering for Materials Synthesis workshop on October 9–11, 2018 (see Appendices 1–3, pp. 45–48). Workshop participants defined opportunities and challenges for future efforts by considering a foundation of existing experimental work relevant to the biosynthesis of three classes of renewable inorganic biomaterials: (1) inorganic biominerals, (2) inorganic-organic hybrids, and (3) composites of inorganic materials and living cells.

59 BASIC BIOLOGICAL SCIENCES↗

Technologies for Characterizing Molecular and Cellular Systems Relevant to Bioenergy and Environment. Workshop report, September 21–23, 2016

The Biological Systems Science Division (BSSD) within the U.S. Department of Energy’s (DOE) Office of Biological and Environmental Research (BER) funds basic research on plants and microbes relevant to several DOE bioenergy and environmental mission areas. BSSD’s long history of developing and supporting genomic characterization of biological systems has led, in part, to the high-throughput DNA sequencing technology available to researchers worldwide. In recent years, genome sequencing has vastly outpaced the ability to interpret genome function. Fully maximizing this wealth of data will require new technology advancements, along with improvements and an increase in the throughput of existing methods for characterizing molecular- to cellular-level processes important for inferring biological function. BSSD research seeks to understand the fundamental genome-encoded properties of plants and microbes that can be harnessed or redesigned for beneficial purposes. Current emphases are leading to the discovery, development, and understanding of numerous plant and microbial species with traits suitable for the production of fuels and chemical products from renewable biomass that could be grown synergistically with food or animal feed crops while not competing with other societal needs. Additionally, BSSD further supports research leading to an understanding of the complex and essential interactions among plants, microbial communities, and the environment to find new ways to sustainably produce biomass for a range of bioenergy and bioproduct applications. This research also is relevant for incorporation into larger-scale environmental models such as those developed through the research supported by BER’s Earth and Environmental Systems Sciences programs.

59 BASIC BIOLOGICAL SCIENCES↗

Adaptive responses and latent costs of multigeneration cadmium exposure in parasite resistant and susceptible strains of a freshwater snail

Population response to anthropogenic activities will be influenced by prior adaptation to environmental conditions. We tested how parasite-resistant and -susceptible strains of a freshwater snail responded to cadmium and elevated temperature challenges after having been exposed to low-level cadmium continuously for multiple generations. Snails exposed to cadmium for three generations were removed for the fourth generation, and challenged in the fifth generation with (1) chronic cadmium exposure over the entire life cycle, (2) acute cadmium exposure of adults, and (3) elevated temperature challenge of adults. The parasite susceptible NMRI strain is more cadmium tolerant than the parasite resistant BS90 strain and remained more tolerant than BS90 throughout this study. Additionally, NMRI exhibited greater adaptive capacity for cadmium than BS90 and became more tolerant of both chronic and acute cadmium challenges, while BS90 became more tolerant of acute cadmium challenge only. Fitness costs, reflected in population growth rate, were not apparent in fifth generation snails maintained in cadmium-free conditions. However, costs were latent and expressed as decreased tolerance to a secondarily imposed temperature stress. Adaptation to prior selection pressures can influence subsequent adaptation to anthropogenic stresses and may have associated costs that reduce fitness in novel environments.

54 ENVIRONMENTAL SCIENCES↗

An extension of the high-resolution millimeter- and submillimeter-wave spectrum of methanol to high angular momentum quantum numbers

The high-resolution laboratory millimeter- and submillimeter-wave spectra of C-12H(3)OH and C-13H(3)OH have been extended to include transitions involving significantly higher angular momentum quantum numbers than studied previously. For C-12H(3)OH, the data set now includes 549 A torsional substate transitions and 524 E torsional substate transitions through J is not greater than 24, exclusive of blends. For C-13H(3)OH the data set now includes 453 A torsional substate transitions and 440 E torsional substate transitions through J is not greater than 24, exclusive of blends. The extended internal axis method Hamiltonian has been used to analyze the transitions to experimental accuracy. The molecular constants determined by this approach have been used to predict accurately the frequencies of many transitions through J = 25 not measured in the laboratory.

Anderson, Todd↗

Millimeter- and submillimeter-wave spectrum of highly excited states of water

To facilitate studies of water in the interstellar medium and late-type stars, the frequencies of 30 new millimeter- and submillimeter-wave transitions of H2O-16 have been measured, which lie between 100 GHz and 600 GHz. This represents almost a doubling of the number of water lines that have been observed in the laboratory in this spectral region at high resolution. All of the newly observed lines are highly excited, lying between 2400 and 4200/cm above the ground level. Some of these have large excitation energies because of their high rotational states and others because they lie in excited vibrational states. These lines are potentially of substantial astrophysical significance because they are related to the study of interstellar masers and because their high excitation eliminates the atmospheric self-absorption associated with the more well-known water lines.

Pearson, J. C.↗

The millimeter- and submillimeter-wave spectrum of (C-13)H3OH revisited

A total of 245 previously unobserved millimeter- and submillimeter-wave transitions of (C-13)H3OH for J not above 10 were assigned on the basis of measurements with a spectrometer which uses 40-60 GHz klystrons as fundamental radiation sources. These transitions were combined with the previously assigned 596 transitions and were analyzed using a modified internal-axis-method model which treats the symmetric (A) and degenerate (E) substates separately. As a result of the expansion of the (C-13)H3OH data set to cover the same range as the data set of a previous (C-12)H3OH analysis by Anderson et al. (1990), rigid criteria of self-consistency could be applied for the selection and the value of the constants between the isotopic species. The spectral constants obtained were used to make accurate predictions of 562 additional transitions of (C-13)H3OH for v(t) = 0, 1, 2 and rotational quantum number J equal to or less than 12.

Anderson, Todd↗

Additional measurements and a refined analysis of the millimeter- and submillimeter-wave spectrum of methanol

A total of 414 previously unobserved millimeter- and submillimeter-wave transitions of (C-12)H3OH through J = 10 and v(t) = 2 are assigned. These data and previous measured spectral transitions are combined and fitted by a modified internal axis method (IAM) treatment in which the A and E substates are treated separately and a wide variety of new rotational-torsional interaction terms are employed. The modified IAM treatment reduces the overall rms deviation of the fits to the level of experimental accuracy. The resultant spectroscopic constants allow for the accurate prediction of 569 additional transitions through J = 12 or less.

Anderson, Todd↗

The laboratory millimeter- and submillimeter-wave spectrum of the first two excited torsional states of (C-13)H3OH

The rotational-torsional spectrum of (C-13)H3OH is presented in both the symmetric and degenerate substates of the first two excited torsional states. Of the new transitions reported, 122 lines are from the v(t) = 1 torsional state and 110 lines are from the v(t) = 2 torsional state, and all are confined to the rotational quantum number J = 8 or less. The data are combined with previously reported millimeter and submillimeter data for the v(t) = 0 torsional state and 44 previously measured excited torsional state lines to form a global data set of 596 transitions, which is analyzed and fitted using an extended internal axis method. The fit results in an overall rms deviation of 1.98 MHz. The spectral constants generated by the fit are used to predict an additional 123 lines of (C-13)H3OH in the v(t) = 1,2 excited torsional states with frequencies up to 612 GHz and rotational quantum number J = 11 or less.

Anderson, Todd↗

The laboratory millimeter- and submillimeter-wave spectrum of CH3OD

The millimeter-wave and submillimeter-wave spectrum of CH3OD, a deuterated isotope of methanol known to be present in the interstellar medium, has been studied in the laboratory. Like all isotopes of methanol, CH3OD possesses a complex dense spectrum because of the phenomenon of internal rotation, sometimes referred to as torsional motion. Approximately 300 lines in the frequency range 130-700 GHz have been assigned. These lines involve transitions between rotational states with rotational quantum number J of not greater than 9 in both the A and the E substates of the lowest torsional state (v sub t = 0). The present data and previous data at lower frequencies (longer wavelengths) have been combined and analyzed by a procedure called the 'internal axis method'. The analysis yields spectral constants for CH3OD which, in turn, have been used to predict the frequencies of a number of other transitions of this species not measured in the laboratory.

Anderson, Todd↗

The laboratory millimeter- and submillimeter-wave spectrum of C-13 methanol

A comprehensive millimeter- and submillimeter-wave study of the rotational spectrum of (C-13)H3OH is presented. Approximately 300 new transitions of this species were measured at frequencies up to 650 GHz, and the transitions were analyzed along with previously measured spectra using the internal axis method of Herbst et al. (1984). The resulting spectral constants allow prediction of an additional large number of transitions which should allow astronomers to identify many strong rotational lines of C-13 methanol throughout much of the submillimeter region.

Anderson, Todd↗