Search NASA⌕ Search

Engineering topics

Andrew C. Bergan

Publications and source records attributed to Andrew C. Bergan.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Out of Plane Stresses Using a Beam-Based Elastic Foundation Bonded Joint Model

Efficient, semi-analytical models of bonded joints are utilized for initial joint design and sizing due to their convenience and speed. Many of these models are based on beam and plate theories, which are most applicable when in-plane stresses/strains dominate. While this can be a sensible assumption for obtaining the deformations of the joint, out of plane (transverse) stresses are often of critical importance for failure in bonded joints composed of fiber reinforced composite materials. Since through-thickness strains are neglected in these semi-analytical theories, the present study shows a method to back-calculate the out of plane stresses based on stress balance equations, which use the in-plane stresses and displacements that have already been obtained. The method was implemented within the Joint Element Designer (JED) software, and verification and validation examples have been shown. As is typical for these types of models, corner stress singularities are not captured by the JED model, but the general trends of the stress and deformation fields agreed with a higher fidelity finite element model. As such, this method for obtaining out of plane stresses, when coupled with the JED code, is very useful for the complete stress analysis of bonded composite joints.

composites↗
NASA NTRS2020

Analysis of Open Hole Compression Specimens Using the CompDam Continuum Damage Mechanics Model

This report documents a validation study on the standard Open Hole Compression (OHC) laminate test specimen conducted as part of the NASA Advanced Composites Project (ACP). Tests were conducted on OHC specimens with hard, quasi-isotropic, and soft layups using digital image correlation and X-Ray computed tomography to capture the structural response and damage evolution. Progressive damage models were constructed for use with the CompDam continuum damage mechanics code following the best practices established during the ACP. Detailed interrogation of the analysis results and comparison with experimental measurements provide a basis for assessing the capability of the modeling approach for OHC. The structural response is found to be captured well, with strengths predicted within 3\% of the experimental values for hard and quasi-isotropic laminates. In the soft laminate, the model predicts failure to be more brittle than the nonlinear, ductile response that was measured. Damage states extracted from the models at the same load level as test measurements are overlaid to show directly the similarities and differences between test and analysis results. Studying the damage evolution predicted by the analysis reveals that the failure process is a competition between fiber damage and delamination/sub-laminate buckling, with fiber damage dominating the collapse in the hard laminate and sub-laminate buckling governing in the soft laminate. Finally, a series of parametric studies varying numerical solution parameters (mesh size, mass scaling) and physical properties (fiber direction compressive strength and toughness) reveal sensitivities and deficiencies of the model. To the authors' knowledge, this study is the first for OHC specimens to include detailed evaluation of damage mode interactions, direct overlay of predicted and measured damage states, and sensitivity of the predicted results to difficult-to-measure fiber direction material properties.

Continuum damage mechanics↗
NASA NTRSDate not supplied

Simulation of Deployable Composite Structures Based On Mechanics of Structure Genome

In this paper, a simulation method for analyzing deployable composite structures is presented. With a proper material model, effective plate/shell properties of the composites is obtained based on Mechanics of Structure Genome (MSG), and then implemented into a user subroutine UGENS for global structure simulation in ABAQUS. Column bending test (CBT) and composite boom and hub structure are studied for demonstration. A viscoelastic material model with direct integration implementation is adopted in this paper. CBT simulation shows good agreement with experiments during relaxation, while errors are observed when comparing residual deformation. This simulation can be potentially used as a calibration tool for material properties. After CBT simulation, a demonstrative model with a lenticular boom and the hub is created in ABAQUS. Complete process of flattening, coiling, stowage, deploying and recovery is simulated with the viscoelastic material model. Residual deformation of the boom is analyzed.

Multi-scale modeling↗
NASA NTRSDate not supplied

New Developments in the CompDam Fiber Kinking Model for the Interaction

This paper describes two new additions to the CompDam fiber kinking model: 1) a failure index for fiber kinking to facilitate interaction between kinking and matrix cracking and 2) a strain-based criterion for fiber rupture to account for fiber breakage before or after fiber kinking. The model formulation is described with the aid of the graphical Considère construction, which is used to determine the conditions for fiber kinking. Verification studies are conducted with single element models to show the behavior of the model in light of the new developments and to evaluate the effect of numerical parameters of the model. The model is used to analyze open hole compression (OHC) specimens with soft, quasi-isotropic, and hard layups. Analysis results are shown for a conventional continuum damage mechanics model using a trilinear constitutive law for fiber damage and for the proposed model to highlight the differences between the two. Comparison with test data highlights the capabilities and remaining gaps in the quantitative prediction of the damage and failure response. While both models can predict many features of the OHC response, accurate prediction of kinking onset in the OHC specimens remains elusive. The results suggest that it is necessary to predict the combined effects of compression and shear loading as well as the structural effects (e.g., ply thickness, strain gradient effect) accurately to match the experimental observations of fiber kinking onset in the three OHC laminates.

Andrew C. Bergan↗
NASA NTRSDate not supplied

Multiscale Simulation of Deployable Composite Structures

In this paper, a multiscale simulation method for analyzing deployable composite structures is presented. Effective shell properties of the composites are obtained based on Mechanics of Structure Genome (MSG) homogenization, and then implemented into a user-subroutine UGENS for structural simulation with shell elements in Abaqus. The column bending test(CBT) of a flat thin flexure and lenticular composite boom in a simplified deployer structure are studied for demonstration. A viscoelastic material model with direct integration is adopted in this paper. The CBT simulation shows good agreement with experiments during relaxation, while errors are observed when comparing residual deformation. It is shown that this CBT model can be calibrated to CBT test results. For the lenticular boom analysis, the complete process of flattening, coiling, stowage, deployment and recovery is simulated with the viscoelastic shell model.

Finite element analysis↗