Andrew N Leidy | Search NASA

NASA NTRS2024

Transitional Flow in the Wake of a Pseudorandom Roughness on a Supersonic Flat Plate

Prediction of roughness-induced transition is a practical requirement for the optimized design of high-speed vehicles, which rely on a reduction of thermal stresses and drag for higher performance. This reduction is affected by boundary layer transition, which on real vehicles may be caused by unavoidable roughness such as inherent surface material roughness and deterioration or roughness in the form of sensing elements, fasteners, etc. A better understanding of transition resulting from roughness can help inform acceptable manufacturing tolerances or maintenance requirements on real vehicles.

Amanda Chou↗

NASA NTRS2023

BOLT II Forebody Surface Measurement Analysis

Surface impression molds of the nosetip/forebody interface, discrete tripping elements, and other surface imperfections were formed on the BOLT II flight vehicle prior to its launch in March 2022. The silicon-rubber molds cast on the interface between the nickel nosetip and the stainless steel forebody were measured using a 3D optical measurement system and a stylus profilometer and were evaluated for step direction and height. The step around the nosetip/forebody interface was found to vary in both magnitude and direction, but values were generally modest with most samples below 60 μm across the span and only two samples, both cast in the gutter, with step values larger than 100 μm. Impressions of the secondary-side tripping elements were strictly scanned with the optical device and similar methods were used to calculate trip height as step height. The measured centerline trip height was 2623 ±12 μm, while the leading-edge, quadrant 2 and 3, trip heights were 897 ±5 μm and 891 ±18 μm, respectively. Surface imperfections on the nose and forebody were also evaluated. Surface roughness values and spectra were estimated, and profiles were extracted across the imperfections to quantify the magnitude of those features.

Trip height↗

NASA NTRS2021

Hypersonic Second Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRSDate not supplied

Some Effects of Tunnel Noise on Cylinder-Induced Mach 6 Transitional Shock Wave Boundary Layer Interactions

Experiments were conducted on a cylinder-induced shock wave boundary layer interaction (SBLI)as its state was brought through transition using a combination of boundary layer trips and Reynolds number sweep. A baseline case with no trips was also examined. The measurements were made in a Mach 6 freestream in the well-characterized Actively Controlled Expansion tunnel, which demonstrated a near tripling in fluctuation levels with unit Reynolds number increase from 3.0 to 3.5 million per meter. Surface oil flow and schlieren images suggested the jump in freestream noise served as the impetus for SBLI transition since the flow separation distance began to decrease as the Reynolds number progressed through those conditions. Likewise, surface mounted Kulite® pressure transducers indicated a rise in surface pressure fluctuations as well as initial growth in the instability responsible for transitioning the boundary layer within the interaction. Finally, heat transfer rates within the tripped SBLI were shown to be affected by the jump in freestream disturbance levels.

Andrew N Leidy↗

NASA NTRSDate not supplied

Bluntness and Supersaturation Effects on the Second Mode Instability in Mach 10 Flow

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 31-Inch Mach 10 Tunnel to investigate the impact of nosetip radius and freestream supersaturation on the development of the second mode instability. The model was instrumented with surface-mounted Kulite® and PCB® pressure transducers and thermocouples. Power spectral density plots demonstrate the anticipated trends of the second mode instability weakening and shifting to lower frequencies with increased bluntness. Heat transfer measurements suggest laminar flow over the bulk of the model for most testing conditions, with evidence of transition by the cone base for the sharpest nosetip (R = 0.15 mm) at the higher unit Reynolds numbers. The dynamic surface pressure and heat transfer measurements show that reducing the temperature of the freestream to a supersaturated state has a significant stabilizing effect on the model boundary layer. The surface measurements are observed to be highly dependent on the level of clustering in the freestream. Significant changes in surface pressure spectra due to total temperature reduction are first noted below T0= 948 K, while more substantial fluctuation reductions are found below T0= 810 K.

Hypersonics↗

NASA NTRSDate not supplied

Measurements and Computations of the Turbulent Corner Flow on the NASA Juncture-Flow Model with a Symmetric Wing

The NASA Juncture Flow experiment is designed to acquire high-quality flowfield data deep in the corner of a wing-fuselage junction specifically for the purpose of computational fluid dynamics (CFD) validation and turbulence model improvement. This paper presents and discusses the results of a recent experiment with the juncture-flow model in the NASA Langley 14- by 22-Foot Subsonic Tunnel. The main objective of the test was to expand the existing juncture-flow dataset with a symmetric wing case that displays fully attached, incipient separation, and separated flow in the corner of the wing-fuselage junction, depending on the model angle of incidence. Laser Doppler velocimetry (LDV) measurements were made at three model angles of incidence (0 deg: fully attached, 1 deg: incipient separation, and 5 deg: separated flow) and for each one, mean-flow and Reynolds-stress data were obtained on the fuselage and at several streamwise locations along the corner of the wing-fuselage junction. Supporting measurements were made during the test campaign and included model and tunnel wall static pressures, tunnel wall and ceiling boundary-layer rake data, oil-flow visualizations, and laser-based measurements of the as-built model geometry and model position in the test section. Comparisons between the experimental data on the test article and Reynolds-averaged Navier-Stokes CFD results are presented and discussed.

Juncture Flow↗

NASA NTRSDate not supplied

NASA LaRC Hypersonic Experimental Aerothermodynamic Capabilities and Recent Contributions

A review is presented of recent research, development, testing and evaluation aerothermodynamic activities that have been conducted at the NASA Langley Research Center in the Langley Aerothermodynamics Laboratory. An overview of the test facilities, model development and fabrication capabilities, and instrumentation and measurement techniques employed in this work is provided. Contributions to hypersonic flight and planetary exploration programs are detailed, as are fundamental research and development activities. Wind tunnel investigations are described that supported flight programs for NASA and Commercial Crew external partners. Collaborations between NASA projects and academia are also highlighted in this overview of recent wind tunnel experiments.

hypersonic↗

NASA NTRSDate not supplied

NASA Langley Hypersonic Experimental Aerothermodynamic Capabilities and Recent Contributions

A review is presented of recent research, development, testing and evaluation aerothermodynamic activities that have been conducted at the NASA Langley Research Center in the Langley Aerothermodynamics Laboratory. An overview of the test facilities, model development and fabrication capabilities, and instrumentation and measurement techniques employed in this work is provided. Contributions to hypersonic flight and planetary exploration programs are detailed, as are fundamental research and development activities. Wind tunnel investigations are described that supported flight programs for NASA and Commercial Crew external partners. Collaborations between NASA projects and academia are also highlighted in this overview of recent wind tunnel experiments.

hypersonic↗