Search NASA⌕ Search

Engineering topics

Andrew P Santos

Publications and source records attributed to Andrew P Santos.

11 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2026

Manufacturing and Scale-Up of Natural Fiber Composite eVTOL Propeller Skin and C-Channel

This report presents the manufacturing and scale-up of natural fiber composites for aerospace applications, conducted within NASA’s Convergent Aeronautics Solutions portfolio to advance aircraft capabilities and efficiency. The effort focused on the development and demonstration of two proof-of-concept articles, an Electric Vertical Take-off and Landing (eVTOL) propeller skin and a C-channel, produced through an iterative design and process optimization approach. Best practices and guidance on addressing key challenges with bio-based composite materials and manufacturing is provided. Ideally suited for non-load-bearing structural components, these emerging materials offer potential for weight reduction, vibration damping, noise mitigation, interference-free communication, and cost savings, without compromising the performance of safety-critical primary structures.

Natural fibers↗
NASA NTRSDate not supplied

Packing and flow particle simulations

Granular material is present across natural and industrial processes on Earth and other planets. Granular particles show up in space exploration (lunar regolith), avalanches (boulders), food (coffee), construction (concrete powder) and manufacturing (additive manufacturing powder, battery slurries). Important phenomena emerge from large collections of granular particles. The size scales of the particles in granular material, 10 μm diameter or larger, makes particle-based simulations a tractable computational method. This seminar will present the packing and flow of granular matter using particle-based discrete element modeling simulations. Particles modeled with rotational friction only require as few as 2.6 contacts for mechanical stability, as opposed to 6 contacts for frictionless particles. Optimal parameters for in-space manufacturing particulate material are identified. Specifically, the maximum density and contacts occurs for a large-to-small particle volume ratio of 0.265. Stress and contact fabric fluctuations of flowing dry granular matter have power-law scaling with strain rate, and a kink. The pressure-dependent slope change kink could identify the transition between slower, quasistatic and faster, inertial flows.

granular↗
NASA NTRSDate not supplied

Particle-Based Fiber Models of Woven Materials for Earth Entry Thermal Protection

Applications requiring materials with layer-to-layer strength, from basketry to thermal protection systems, use interlaced, three-dimensional woven materials. NASA is developing and deploying woven material heat shields for missions, including Artemis I (3D-MAT for compression pads) and potentially Mars Sample Return - Earth Entry System. These materials are complex, hierarchical and must protect from extreme environments and phenomena, such as deformation, impact and high-enthalpy heating. Woven material performance depends on microstructure, damage and weave geometry. Therefore, fiber-specific models are needed to simulate fiber contacts within the weave hierarchical geometry (fiber to tow to yarn to weave) and the inherent directionality of fibers. Explicit fiber models can simulate how weave microstructure evolution affects thermal and mechanical properties. We parameterize a discrete element bonded particle models (DEM-BPM) of fibers to capture thermal and mechanical behavior within and between fibers, with bonded and contact forces, respectively. We study the proportion of heat transfer and stress via the contact network, fiber bonds and the weave geometry, for example, with respect to yarn warp-weft identity (whether it interlaces weave layers). Our results demonstrate the importance of explicit fiber modeling for connecting microstructure with thermal and mechanical properties.

woven material↗
NASA NTRSDate not supplied

Fracture of Charring Avcoat With Meshfree Material Response-Coupled Fracture Approach

Fracture of thermal protection systems (TPS) is typically unfavorable, but often unavoidable. TPS can fracture during entry, manufacturing or from impact. Many NASA missions use ablative materials for TPS, including the fore-body for Dragonfly (PICA) and Orion for Artemis-I (Avcoat). The material response to thermal and mechanical loads during entry is integral to TPS sizing, design and analysis. The fracture of TPS also depends, and can be caused by, the change of material properties during entry. Simulations that resolve fracture of TPS due to thermo-mechanical forces can identify TPS failure mechanisms and be applied to conditions inaccessible to ground testing. We present simulation work using a mesh-free/Lagrangian approach to solving continuum mechanics, coupled to material response. Two different materials are simulated under different model entry-like boundary conditions. The dynamic crack structure is analyzed and compared across simulations. Crack analyses inform the role of design features, such as entry trajectories and manufacturing-influenced material properties, play in TPS fracture.

Andrew P Santos↗
NASA NTRSDate not supplied

Particle-Based Fiber Models of Woven Materials for Earth Entry Thermal Protection

Applications requiring materials with layer-to-layer strength, from basketry to thermal protection systems, use interlaced, three-dimensional woven materials. NASA is developing and deploying woven material heat shields for missions, including Artemis I (3D-MAT for compression pads) and potentially Mars Sample Return - Earth Entry System. These materials are complex, hierarchical and must protect from extreme environments and phenomena, such as deformation, impact and high-enthalpy heating. Woven material performance depends on microstructure, damage and weave geometry. Therefore, fiber-specific models are needed to simulate fiber contacts within the weave hierarchical geometry (fiber to tow to yarn to weave) and the inherent directionality of fibers. Explicit fiber models can simulate how weave microstructure evolution affects thermal and mechanical properties. We parameterize a discrete element bonded particle models (DEM-BPM) of fibers to capture thermal and mechanical behavior within and between fibers, with bonded and contact forces, respectively. We study the proportion of heat transfer and stress via the contact network, fiber bonds and the weave geometry, for example, with respect to yarn warp-weft identity (whether it interlaces weave layers). Our results demonstrate the importance of explicit fiber modeling for connecting microstructure with thermal and mechanical properties.

woven material↗
NASA NTRSDate not supplied

Strong Thermoset Regolith UV-Curable Composite Technology (STRUCT) Overview

Future lunar surface missions require construction materials that can be manufactured in situ using lo-cal resources while operating under extreme environmental conditions. Many Lunar material demands can be solved solely with regolith by compacting or sintering. And yet past Lunar missions rely on polymeric materials, and sustained Lunar missions must reduce Earth-supplied polymers dependence. Dual-cure (Ultraviolet (UV) and thermal) polymer-regolith composites offer a promising pathway by leveraging solar UV radiation, moderate thermal in-put, and regolith. Mission mass limits, power availability and energy constraints on the lunar surface further motivate low-energy processing and curing strategies for surface construction materials. The Strong Thermoset Regolith UV-Curable Composite Technology (STRUCT) project has successfully synthesized and demonstrated dual-cure photopolymer resins derivable from in-situ resources [3]. Morphological, thermal, and mechanical characterization show that the newly formulated UV curable resin systems integrates well with lunar regolith simulants. Processing and chemistry changes, and computational analysis advanced the composite design. X-ray CT scanned and computational analysis demonstrate that resin, regolith and additives are well incorporated. The large fraction of regolith, 95% by mass, large char yield (82% mass), low thermal conductivity (0.26 W/m/K), confirm this material as a promising high-performance thermal and structural material.

thermal conductivity↗
NASA NTRSDate not supplied

Natural Fiber Simulations and Analysis for Composites

As the U.S. government and the aviation industry strive to achieve net-zero carbon emissions by 2050, the Sustainable Manufacturing of Aircraft (SUMAC) project, supported by the Convergent Aeronautics Solutions (CAS) program of the National Aeronautics and Space Administration (NASA), aims to develop sustainably derived thermoplastic composites and manufacturing technologies for future aviation. A multidisciplinary team of experts drives this initiative through a collective effort. The team’s key focus areas are sustainably derived thermoplastic resins, natural fiber reinforcement, composite manufacturing, structural health monitoring, computational materials modeling, and systems analysis. This presentation will give an overview of the SUMAC project. Fiber-scale microscopy analysis characterized fiber cross sections finding that hemp and flax fibers are very deformable and non-circular (circularities of 0.2 were observed), and diameters range from submicron to 20 μm. Fiber shapes range from flattened, with aspect ratios Rlong/Rshort up to 5, to round, Rlong/Rshort =1. And Fiber core perimeters, which likely drives deformability, were calculated Pcore=7 μm. Explicit-fiber yarn simulations, parameterized from single-fiber measurements, resolved and identified slack as a cause for yarn strain-hardening tensile behavior. The bonded network model of PLA, PHA and PA11 resins captures tensile behavior, and can model an infused weave. Computational models of the weave unit cells matched the pattern (including plain, twill and triaxial braid), yarn ply (1to 2), and yarn twist from optical microscopy.

thermoplastic↗
NASA NTRSDate not supplied

Natural Fiber Simulations and Analysis for Composites

As the U.S. government and the aviation industry strive to achieve net-zero carbon emissions by 2050, the Sustainable Manufacturing of Aircraft (SUMAC) project, supported by the Convergent Aeronautics Solutions (CAS) program of the National Aeronautics and Space Administration (NASA), aims to develop sustainably derived thermoplastic composites and manufacturing technologies for future aviation. A multidisciplinary team of experts drives this initiative through a collective effort. The team’s key focus areas are sustainably derived thermoplastic resins, natural fiber reinforcement, composite manufacturing, structural health monitoring, computational materials modeling, and systems analysis. This presentation will give an overview of the SUMAC project. Fiber-scale microscopy analysis characterized fiber cross sections finding that hemp and flax fibers are very deformable and non-circular (circularities of 0.2 were observed), and diameters range from submicron to 20 μm. Fiber shapes range from flattened, with aspect ratios Rlong/Rshort up to 5, to round, Rlong/Rshort =1. And Fiber core perimeters, which likely drives deformability, were calculated Pcore=7 μm. Explicit-fiber yarn simulations, parameterized from single-fiber measurements, resolved and identified slack as a cause for yarn strain-hardening tensile behavior. The bonded network model of PLA, PHA and PA11 resins captures tensile behavior, and can model an infused weave. Computational models of the weave unit cells matched the pattern (including plain, twill and triaxial braid), yarn ply (1to 2), and yarn twist from optical microscopy.

thermoplastic↗
NASA NTRSDate not supplied

Thermomechanical Modeling of Woven Materials With Particle-Based, Explicit-Fiber Simulations

Fiber-based materials are extensively used to protect spacecraft during entry. Insulative fibers, often in a fiber network or woven, provide rigidity, strength, and control of material anisotropy and density. Woven thermal protection materials, such as ADEPT (Adaptable, Deployable Entry and Placement Technology), 3D-MAT (3-Dimensional Multifunctional Ablative Thermal Protection), and 3MDCP (3D Woven Mid-Density Carbon Phenolic), enable missions with stronger and denser materials for entry profiles with high shear and heat flux. Vulnerabilities to woven thermal protection materials include manufacturing-induced material property variation, and impact from micrometeoroids. Simulating woven materials under these conditions require models that can resolve hierarchal structures, thermomechanical behavior, and failure. To address this, we simulate weave thermal conduction and mechanical deformation. We simulate the full weave with a coarse-grained yarn model is presented. The model combines a validated, high-resolution single 3MDCP yarn model and phenolic resin model. Instead of modeling every fiber, each yarn ply with order 10, instead of order 1000, fibers. The discrete element bonded particle model (DEM-BPM) of fibers captures the thermal and mechanical behavior within and between fibers. We study the proportion of heat transfer and stress via the contact network, fiber bonds, and overall weave geometry.

bonded particle↗