Search NASA⌕ Search

Engineering topics

Andrews, J. B.

Publications and source records attributed to Andrews, J. B..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Wetting Characteristics of Immiscibles

Early microgravity experiments with immiscible alloys were usually carried out with the intent of forming dispersed microstructures. By processing under microgravity conditions, the main mechanism leading to gross phase separation could be eliminated. However, analysis of flight samples revealed a separated structure where the minor phase was present along the outer surface, while the major phase was present in the center. The Wetting Characteristics of Immiscibles (WCI) project, which flew aboard the USMP-4 (United States Microgravity Payload) mission in November of 1997, was designed to gain insight into the mechanisms causing segregation of these alloys. This investigation utilized an immiscible transparent organic alloy system and a transparent container in order to facilitate direct observation of the separation process. A range of immiscible alloy compositions was utilized in order to obtain variations in the minor and major phases present and observe the influence on the segregation processes. A small composition range was found where the minor liquid phase perfectly wet the cell gasket. Unexplained observations were made at the extremes of the composition range.

Andrews, J. B.↗
NASA NTRS1992

The influence of gravity level during directional solidification of immiscible alloys

During directional solidification of immiscible (hypermonotectic) alloys it is theoretically possible to establish a stable macroscopically-planar solidification front, and thus avoid sedimentation. Unfortunately, convective instabilities often occur which interfere with the directional solidification process. In this paper, stability conditions are discussed and results presented from directional solidification studies carried out aboard NASA's KC-135 zero-g aircraft. Samples were directionally solidified while the effective gravity level was varied from approximately 0.01 g for 25 s to 1.8 g for 45 s. Dramatic variations in microstructure were observed with gravity level during solidification.

Andrews, J. B.↗
NASA NTRS1991

Directional solidification in immiscible systems - The influence of gravity

The possibility of producing aligned fibrous composite microstructures with a high volume fraction of the immiscible phase, L2, through the directional solidification of hypermonotectic alloys is examined. Early work suggests that low gravity conditions are necessary to prevent sedimentation of the more dense L2 phase. However, if convective flows result, they disrupt the formation of the desired fibrous microstructure and produce a disperse structure. The need for long-duration low-g experiments is emphasized.

Andrews, J. B.↗
NASA NTRS1991

The effect of processing conditions on solidified structures in immiscible systems

The incentive for low-gravity processing of immiscible alloys is usually tied to an attempt to eliminate sedimentation of the more dense immiscible liquid phase during processing. However, many other factors can influence the solidified structure of these alloys. For example, crucible wetting by one of the immiscible liquid phases during normal (non-directional) low-gravity solidification in a container has been shown to often lead to a completely separated structure. For containerless, low-gravity processing, alloy composition has a tremendous affect on the structure formed. During directional solidification, alloy composition, thermal gradient, solidification rate, convective instability and the miscibility gap height of the system all have a major effect on the structures obtained. This paper discusses the conditions necessary for the production of desired microstructures in each of these processing techniques. Examples are shown of samples processed under both desirable and undesirable conditions.

Andrews, J. B.↗
NASA NTRS1988

Influence of gravity level and interfacial energies on dispersion-forming tendencies in hypermonotectic Cu-Pb-Al alloys

Results on the nondirectional solidification of several hypermonotectic Cu-Pb-Al alloys were obtained aboard NASA's KC-135 zero-gravity aircraft in order to determine the influence of interfacial energies and gravity levels on dispersion-forming tendencies. The Al content was systematially varied in the alloys. The dispersion-forming ability is correlated with gravity level during solidification, the interfacial energy between the immiscible phases, and the tendency for the minority immiscible phase to wet the walls of the crucible.

Andrews, J. B.↗
NASA NTRS1988

The influence of interfacial energies and gravitational levels on the directionally solidified structures in hypermonotectic alloys

Various Cu-Pb-Al alloys were directionally solidified under 1-g conditions and alternating high-g/low-g conditions (achieved using NSAS's KC-135 aircraft) as a means of studying the influence of interfacial energies and gravitational levels on the resulting microstructures. Directional solidification of low Al content alloys was found to result in samples with coarser more irregular microstructures than in alloys with high Al contents under all the gravity conditions considered. Structures are correlated with interfacial energies, growth rates, and gravitational levels.

Andrews, J. B.↗
NASA NTRS1986

Containerless processing of hypermonotectic and glass forming alloys using the Marshall Space Flight Center 100 meter drop tube facility

Two separate projects were carried out to study alloys whose solidification structures can be strongly influenced by the presence of a container during melting and solidifications. One project involved containerless solidification of hypermonotectic Au35Rh65 alloys. This alloy exhibits liquid immiscibility over a temperature range. It has been suggested that containerless melting might be one solution to the problem of sedimentation in the dispersions of immiscible liquid phases. However, surface tension driven flows could also lead to accumulation of the minority liquid phase at the external surface of a containerlessly melted alloy. The research underway is a first step in determining the influence of containerless, microgravity processing on immiscible alloys. Nickel-niobium alloys were studied using the drop tube facility. One alloy in this system, a Ni60Nb40 alloy, is a good candidate for the formation of a bulk metallic glass. Amorphous alloys of this composition were produced using thin film and mechanical alloying techniques. However, theory indicates that if heterogeneous nucleation can be avoided, it should be possible to produce an amorphous structure in this system using a moderate cooling rate from the melt. The containerless melting and solidification capabilities of the drop tube faciltiy provide ideal conditions for a study of this type. To date, several Ni60Nb40 samples have been levitated, melted and cooled during 4.6 seconds of free fall in the 100 meter drop tube. Structures obtained are discussed.

Andrews, J. B.↗
NASA NTRS1972

Analysis of thermal stress and metal movement during welding

Objectives of study were: investigation of temperature changes caused by welding arc with analysis of temperature distribution; development of system of mathematical statements describing thermal stresses and plastic strains during welding; and development of system of mathematical solutions and computer programs for one-dimensional analysis.

Andrews, J. B.↗