Effect of Fluid Properties on Contact Angles in the Eagle Ford Shale Measured with Spontaneous Imbibition
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Engineering topics
Anovitz, Lawrence M.
Publications and source records attributed to Anovitz, Lawrence M..
Role of Mineralogy in Controlling Fracture Formation
The presence of fractures in caprocks can pose increased risks in subsurface energy systems and processes like CO 2 sequestration by introducing high-permeability leakage paths. Fracture apertures and permeability can be altered through mineral dissolution and precipitation reactions, but the reactive evolution of fractures is not well understood. In fractures, minerals that are otherwise inaccessible to reactive fluids can become exposed, resulting in mineral reactions unpredicted by bulk formation data. This work seeks to understand the relationship between mineralogy and fracture formation to enhance our understanding of reactive fracture evolution and CO 2 leakage potential. Here, the mineral compositions of mechanically induced fracture surfaces in samples of the Mancos and Marcellus shales have been quantified and compared to those of the near-fracture matrices using imaging and bulk X-ray diffraction (XRD) data. In the Mancos shale, the concentrations of clay minerals are enhanced along fracture surfaces with respect to the bulk, and the fracture is most likely to form at kaolinite–kaolinite interfaces. Further, evaluation of the mineralogical spatial variability through cross-correlation analysis of the surrounding matrix in images of samples cut perpendicular to the fracture shows that clay is 16.7 times more likely to be present than carbonate minerals near the fracture surface. The high correlation persists roughly 200 μm into the surrounding matrix for the Mancos sample and implies that the fracture formed within a defined clay-rich lithofacies.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Degradation of Adsorbed Bisphenol A by Soluble Mn(III)
Bisphenol A (BPA), a high production volume chemical and potential endocrine disruptor, is found to be associated with sediments and soils due to its hydrophobicity (log K OW of 3.42). Here, we used superfine powdered activated carbon (SPAC) with a particle size of 1.38 ± 0.03 μm as a BPA sorbent and assessed degradation of BPA by oxidized manganese (Mn) species. SPAC strongly sorbed BPA, and desorption required organic solvents. No degradation of adsorbed BPA (278.7 ± 0.6 mg BPA g –1 SPAC) was observed with synthetic, solid α-MnO 2 with a particle size of 15.41 ± 1.35 μm; however, 89% mass reduction occurred following the addition of 0.5 mM soluble Mn(III). Small-angle neutron scattering data suggested that both adsorption and degradation of BPA occurred in SPAC pores. The findings demonstrate that Mn(III) mediates oxidative transformation of dissolved and adsorbed BPA, the latter observation challenging the paradigm that contaminant desorption and diffusion out of pore structures are required steps for degradation. Soluble Mn(III) is abundant near oxic-anoxic interfaces, and the observation that adsorbed BPA is susceptible to degradation has implications for predicting, and possibly managing, the fate and longevity of BPA in environmental systems.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Sol-gel synthesis of nano-scale, end-member albite feldspar (NaAlSi 3 O 8 )
Feldspars are the most abundant minerals in the Earth’s crust, and are also important constituents of many lunar rocks and some stony meteorites. Albite (NaAlSi 3 O 8 ) makes up the sodium corner of the feldspar ternary diagram (KAlSi 3 O 8 - NaAlSi 3 O 8 – CaAl 2 Si 2 O 8 ) and connects the alkali-feldspar and plagioclase binary joins. Synthesis of albite, however, has long been a problem, even at high temperatures and even at high pressures when dry. In fact, most successful syntheses require the combination of high-pressure, high-temperature, and hydrothermal environments. Here, this paper presents a sol–gel method of albite synthesis that requires hydrothermal processing followed by high-temperature recrystallization, but no high-pressure environments. This has the advantage of allowing synthesis of relatively large amounts of material and controlled elemental substitutions.
Albite↗
Influence of microstructure on replacement and porosity generation during experimental dolomitization of limestones
Replacement reactions commonly alter the multiscale pore structures of rocks during fluid-rock interactions. Analysis of these processes in various model fluid-rock systems during controlled laboratory experiments provides insights into the origins of microstructures found in natural materials. This study focused on understanding the effects of initial starting material permeability and resultant differences in transport pathways on porosity and mineralogical changes during limestone dolomitization.A series of replacement experiments (32–317 days in duration) have been conducted in which 1.59 cm (5/8 in.) diameter cores of two different limestones were reacted with saturated MgCl2 solutions at 200 °C. The Texas Cream (Austin Chalk) is a high-porosity, high-permeability limestone, whereas both the porosity and permeability of the Carthage Marble (Burlington Limestone) are relatively low. Altered limestones were imaged using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS) and electron microprobe analysis (EMPA). A representative grain boundary of the low-porosity limestone was targeted for a focused ion beam (FIB) lift-out and characterized using transmission electron microscopy (TEM). These results were coupled with analyses of radial changes in the porosity distribution of the core derived from X-ray and neutron small- and ultra-small angle scattering ((U)SANS/(U)SAXS).The high-porosity/permeability limestone showed a four times faster bulk replacement rate than the lower-porosity/permeability material, and a different mechanism of porosity development. For the low-porosity limestone, a two-stage replacement occurred, with the reacted region of the core consisting of an inner rim in which the limestone was replaced by two calcite-dolomite solid solutions, and an outer rim in which the dolomite was replaced by magnesite. Elongated pores formed along grain boundaries at the initial limestone/dolomite reaction interface, and additional nanometer-scale porosity was formed at the secondary magnesite replacement rim. Grain boundaries were identified as preferential pathways for transport leading to dolomitization and a grain boundary diffusion rate was calculated based on microstructural characterization. In contrast, replacement in the high-porosity limestone was accompanied by porosity generation through replacement of individual grains by dolomite throughout the sample and, in longer runs, magnesite in outer parts of the core. These observations emphasize that both the mechanisms of the replacement reaction and the microstructure and chemistry of the replaced product are contingent on the initial structure of the starting material.
36 MATERIALS SCIENCE↗
Direct determination of the zero-field splitting for the Fe 3+ ion in a synthetic polymorph of NaMgFe(C 2 O 4 ) 3 ·9H 2 O: A natural metal-organic framework
Here we employed inelastic neutron scattering (INS), specific heat, and magnetization analysis to study the magnetism in a synthetic polymorph of the quasi-two-dimensional natural metal-organic framework material, stepanovite NaMgFe(C 2 O 4 ) 3 ∙9H 2 O. No long-range magnetic order can be observed down to 0.5 K. The INS spectra show two dispersionless excitations at energy transfer 0.028(1) and 0.050(1) meV at base temperature, which are derived from the magnetic transitions between zero-field splitting (ZFS) of S = 5/2 ground state multiplets of Fe 3+ ion. Further analysis of the INS results shows that the Fe 3+ ion has an easy-axis anisotropy with axial ZFS parameter D = –0.0128(5) meV and rhombic parameter E = 0.0014(5) meV. The upward behavior at zero field and Schottky-like peak under magnetic field of the low-temperature magnetic specific heat further support the INS results. Our results clearly reveal the magnetic ground and excited state of this stepanovite polymorph.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Oxidation and Associated Pore Structure Modification During Experimental Alteration of Granite
Weathering plays a crucial role in a number of environmental processes, and the microstructure and evolution of multi-scale pore space is a critically important factor in the weathering of geological formations. In igneous rocks the infiltration of meteoric water into initially relatively dry material can cause the rock to begin to disaggregate, increasing porosity and surface area, and allowing further disaggregation and weathering to occur. These processes, in turn, allow biota to colonize the rock, further enhancing the weathering rate. In some igneous rocks this may be driven by oxidation of primary minerals. One such mineral, biotite, has been repeatedly mentioned as a cause of cracking during oxidation. However, the scale-dependence of the processes by which this occurs are poorly understood. We cannot, therefore, accurately extrapolate laboratory reaction rates to the field in predictive numerical models. In order to better understand the effects of oxidation and test the hypothesis that fracture and disaggregation are initiated by swelling of oxidizing biotites, we reacted granite cores in a selenic acid-rich aqueous solution at 200°C for up to 438 days. Elevated temperatures and selenic acid were used to provide relatively fast reaction rates and highly oxidizing conditions in sealed reaction vessels. These experiments were analyzed using a combination of imaging, X-ray diffraction, Mössbauer spectroscopy, and small- and ultra-small angle neutron scattering to interrogate porosity and microfracture formation. The experimental results show little observable biotite swelling, but significant transport and growth of iron oxides and/or clays along grain boundaries throughout the sample. Significant increases in porosity were also observed at the sample rim, likely associated with feldspar alteration. Fractures and transport were observed throughout the core, suggesting that stresses due to crystallization pressures caused by the growing iron phases may be the initiating factors in granite weathering, possibly followed by biotite swelling after sufficient permeability is achieved.
Anovitz, Lawrence M.↗
Temporal Evolution of Corrosion Film Nano-Porosity and Magnesium Alloy Hydrogen Penetration in NaCl Solution
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
One-Dimensional Glassy Behavior of Ultraconfined Water Strings
Water is renowned for its anomalous behaviors, which can be linked to a distributed H-bond network in bulk water. Ultraconfinement of the water molecule can remove H-bonding, leaving only molecular water. In natural cordierite crystals, water is trapped in an orthorhombic channel with an average diameter of 5.7 Å, running through the center of the unit cell parallel to the c-axis. Calorimetric measurements reveal the existence of a one-dimensional (1D) glass linked to this water. In these channels, water molecules in truncated, sparse 1D strings interact only via dipole–dipole correlations. Here, a physical 1D glass is formed from these strings. This unusual state can be explained by a modified Ising model. This model predicts a dependence of the glass transition temperature, Tg, on the size of these domains. This is confirmed experimentally.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Quantifying Fluid-Wettable Effective Pore Space in the Utica and Bakken Oil Shale Formations
Combined (ultra-) small angle neutron scattering measurements [(U)SANS] and a contrast matching technique were employed to quantify the porosity and pore size distribution from 1 nm to 10 μm and to differentiate accessible (open) pores and inaccessible (closed) pores with respect to organophilic and hydrophilic fluids for two Utica and two Bakken shale samples. Overall, the results indicate that around 40–70% of the pores in the Utica oil shales (mixed carbonate mudstone) are accessible to oil, and 34–37% of the pore surfaces are water-wet. In contrast, the Bakken oil shales (mixed siliceous mudstone and carbonate/siliceous mudstone), which have high total organic carbon contents, have a higher proportion of isolated pore space that is not preferentially wet by oil or water, with less than 36% of the pores accessible to both fluids. In addition, for both formations, pores less than 3 nm in diameter are not oil accessible (organic matter related) but water accessible (clay tactoids related).
58 GEOSCIENCES↗
Carbonation of metal silicates for long-term CO2 sequestration
In a preferred embodiment, the invention relates to a process of sequestering carbon dioxide. The process comprises the steps of: (a) reacting a metal silicate with a caustic alkali-metal hydroxide to produce a hydroxide of the metal formerly contained in the silicate; (b) reacting carbon dioxide with at least one of a caustic alkali-metal hydroxide and an alkali-metal silicate to produce at least one of an alkali-metal carbonate and an alkali-metal bicarbonate; and (c) reacting the metal hydroxide product of step (a) with at least one of the alkali-metal carbonate and the alkali-metal bicarbonate produced in step (b) to produce a carbonate of the metal formerly contained in the metal silicate of step (a).
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Grain detachment and transport clogging during mineral dissolution in carbonate rocks with permeable grain boundaries
In this paper, we explore the effect of permeable grain boundaries on carbonate rock dissolution in order to improve our understanding of grain detachment and migration during reactive flow. To do so we investigated the effects of grain size and enhanced reactivity along grain boundaries on global dissolution kinetics. Variations of permeability and porosity were calculated, and exponential relationships were observed in fractured rocks. Our model employed a reactive transport framework based on the Darcy-Brinkman equation to simulate calcite dissolution in carbonate rocks composed of microporous grains and, included fluid transport along grain boundaries. The model includes fluid flow, solute transport by advection–diffusion, heterogeneous reaction between fluid and minerals and grain detachment with subsequent grain transport in macropores. The migration of solid particles due to dissolution was based on cluster analysis and local movement, and the results show that grain detachment can lead to significant decreases in permeability due to the clogging of transport pathways. Microporous media with smaller grain sizes (fine grains in this study) showed a higher average reaction rate than those with coarser grains. In addition, as the overall rates of geochemical processes are commonly affected by the presence of texture heterogeneities such as fractures, a single fracture (macropore) introduced into a microporous matrix composed of permeable grains and grain boundaries was modelled as a large channel connecting the inlet and outlet of the simulation domain. It was found that macropore clogging by grain detachment temporary decreased permeability, lowering the long-term global reaction rates. Lastly, we observed that increases in flow rate can reduce detachment and fracture clogging by reducing local dissolution along grain boundaries.
58 GEOSCIENCES↗
Correlating inter-particle forces and particle shape to shear-induced aggregation/fragmentation and rheology for dilute anisotropic particle suspensions: A complementary study via capillary rheometry and in-situ small and ultra-small angle X-ray scattering
Predicting the stability of suspensions composed of anisotropic particles is difficult due to the complexity and interplay of hydrodynamic and colloidal forces. For example, it is not well understood how non-spherical particle shapes affect suspension-rheological responses. This study presents evidence showing how the stacking of boehmite platelets dispersed in aqueous solution leads to moderate shear thinning, even at low boehmite mass fractions. Wide angle X-ray, small angle X-ray, and ultra-small angle X-ray scattering were used to simultaneously monitor changes to the size and fractal dimensions of boehmite aggregates from 6 – 10,000 Å as the sample was recirculated through an in situ capillary rheometer. The latter also provided simultaneous measurements of the viscosity of the suspensions. Computational fluid dynamics modeling of the apparatus was used to provide a more rigorous analysis of the fluid flow. In addition to shear-induced aggregation/fragmentation correlated to a complicated balance between hydrodynamic and colloidal forces, the results indicate that orientationally-dependent interactions, arising from non-spherical boehmite aggregate sub-units, may explain the relatively large experimental viscosity when the hydrodynamic force is small compared to colloidal forces. Ultimately, the results from this study can provide a foundation for future work investigating particle shape effects on colloidal and hydrodynamics forces.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗