Search NASA⌕ Search

Engineering topics

Anthony, E J

Publications and source records attributed to Anthony, E J.

Effect of partial carbonation on the cyclic CaO carbonation reaction

CaO particles from the calcination of natural limestones can be used as regenerable solid sorbents in some CO{sub 2} capture systems. Their decay curves in terms of CO{sub 2} capture capacity have been extensively studied in the literature, always in experiments allowing particles to reach their maximum carbonation conversion for a given cycle. However, at the expected operating conditions in a CO{sub 2} capture system using the carbonation reaction, a relevant fraction of the CaO particles will not have time to fully convert in the carbonator reactor. This work investigates if there is any effect on the decay curves when CaO is only partially converted in each cycle. Experiments have been conducted in a thermobalance arranged to interrupt the carbonation reaction in each cycle before the end of the fast reaction period typical in the CaO-CO{sub 2} reaction. It is shown that, after the necessary normalization of results, the effective capacity of the sorbent to absorb CO{sub 2} during particle lifetime in the capture system slightly increases and CaO particles partially converted behave 'younger' than particles fully converted after every calcination. This has beneficial implications for the design of carbonation/calcination loops.

01 COAL, LIGNITE, AND PEAT↗

Long-term behavior of CaO-based pellets supported by calcium aluminate cements in a long series of CO{sub 2} capture cycles

A series of carbonation/calcination tests consisting of 1000 cycles was performed with CaO-based pellets prepared using hydrated lime and calcium aluminate cement. The change in CO{sub 2} carrying capacity of the sorbent was investigated in a thermogravimetric analyzer (TGA) apparatus and the morphology of residues after those cycles in the TGA was examined by scanning electron microscopy (SEM). Larger quantities of sorbent pellets underwent 300 carbonation/calcination cycles in a tube furnace (TF), and their properties were examined by nitrogen physisorption tests (BET and BJH). The crushing strength of the pellets before and after the CO{sub 2} cycles was determined by means of a custom-made strength testing apparatus. The results showed high CO{sub 2} carrying capacity in long series of cycles with an extremely high residual activity of the order of 28%. This superior performance is a result of favorable morphology due to the existence of large numbers of nanosized pores suitable for carbonation. This morphology is relatively stable during cycles due to the presence of mayenite (Ca{sub 12}Al{sub 14}O{sub 33}) in the CaO structure. However, the crushing tests showed that pellets lost strength after 300 carbonation/calcination cycles, and this appears to be due to the cracks formed in the pellets. This effect was not observed in smaller particles suitable for use in fluidized bed (FBC) systems.

01 COAL, LIGNITE, AND PEAT↗

CO{sub 2} capture from simulated syngas via cyclic carbonation/calcination for a naturally occurring limestone: pilot-plant testing

Experiments were performed using a dual fluidized bed reactor system, operated in a batch mode, in order to investigate the effects of steam and simulated syngas on CO{sub 2} capture and sorbent conversion efficiency for a naturally occurring Polish calcitic limestone. In addition, the effect of high partial pressures of CO{sub 2} on the calcination process was examined using either oxygen-enriched air or oxy-fuel combustion in the calciner. As expected, calcination under oxy-fuel conditions resulted in decreased carbonation conversion due primarily to particle sintering and pore pluggage. On average there was a decrease in carbonation conversion of approximately 36.5 and 33.4% for carbonation with steam and steam/simulated syngas, respectively, compared to similar experiments using oxygen-enriched air. However, during the carbonation of the limestone with steam present in the feed gas, it was observed that the high CO{sub 2} capture efficiency period was significantly extended compared to carbonation with only CO{sub 2} present. This resulted in increased CaO conversion from approximately 16.1 to 29.7% for the initial carbonation cycle. A further increase in carbonation conversion from 29.7 to 46.9%, was also observed when simulated syngas conditions (CO, H{sub 2}) were used in the carbonator. Analysis of the outlet gases also confirmed that the calcined limestone catalyzes the water gas shift reaction, which we believe results in enhanced CO{sub 2} concentration levels at the grain surfaces of the sorbent.

01 COAL, LIGNITE, AND PEAT↗

SO{sub 2} Retention by CaO-Based Sorbent Spent in CO{sub 2} Looping Cycles

CaO-based looping cycles are promising processes for CO{sub 2} Capture from both syngas and flue gas. The technology is based on cyclical carbonation of CaO and regeneration of CaCO{sub 3} in a dual fluidized-bed reactor to produce a pure CO{sub 2} stream suitable for sequestration. Use of spent sorbent from CO{sub 2} looping cycles for SO{sub 2} capture is investigated. Three limestones were investigated: Kelly Rock (Canada), La Blanca (Spain), and Katowice (Poland, Upper Silesia). Carbonation/calcination cycles were performed in a tube furnace with both the original limestones and samples thermally pretreated for different times (i.e., sintered). The spent sorbent samples were sulfated in a thermogravimetric analyzer (TGA). The changes in the resulting sorbent pore structure were then investigated using mercury porosimetry. It has been shown that the sulfation rates of both thermally pretreated and spent sorbent samples are lower in comparison with those of the original samples. However, final conversions of both spent and pretreated sorbents after longer sulfation time were comparable or higher than those observed for the original sorbents under comparable conditions. Maximum sulfation levels strongly depend on sorbent porosity and pore surface area. The results showed that spent sorbent samples from CO{sub 2} looping cycles can be used as sorbents for SO{sub 2} retention in cases where significant porosity loss does not occur during CO{sub 2} reaction cycles. In the case of spent Kelly Rock and Katowice samples, sorbent particles are practically uniformly sulfated, achieving final conversions that are determined by the total pore volume available for the bulky CaSO{sub 4} product.

01 COAL, LIGNITE, AND PEAT↗

Sintering and reactivity of CaCO{sub 3}-based sorbents for in situ CO{sub 2} capture in fluidized beds under realistic calcination conditions

Sintering during calcination/carbonation may introduce substantial economic penalties for a CO{sub 2} looping cycle using limestone/dolomite-derived sorbents. Cyclic carbonation and calcination reactions were investigated for CO{sub 2} capture under fluidized bed combustion (FBC) conditions. The cyclic carbonation characteristics of CaCO{sub 3}-derived sorbents were compared at various calcination temperatures (700-925{sup o} C) and different gas stream compositions: pure -2 and a realistic calciner environment where high concentrations of CO{sub 2}>80-90% are expected. The conditions during carbonation were 700 {sup o}C and 15% CO{sub 2} in N{sub 2} and 0.18% or 0.50% SO{sub 2} in selected tests. Up to 20 calcination/carbonation cycles were conducted using a thermogravimetric analyzer (TGA) apparatus. Three Canadian limestones were tested: Kelly Rock, Havelock, and Cadomin, using a prescreened particle size range of 400-650 {mu} m. Calcined Kelly Rock and Cadomin samples were hydrated by steam and examined. Sorbent reactivity was reduced whenever SO{sub 2} was introduced to either the calcining or carbonation streams. The multicyclic capture capacity of CaO for CO{sub 2} was substantially reduced at high concentrations of CO{sub 2} during the sorbent regeneration process and carbonation conversion of the Kelly Rock sample obtained after 20 cycles was only 10.5%. Hydrated sorbents performed better for CO{sub 2} capture but showed deterioration following calcination in high CO{sub 2} gas streams indicating that high CO{sub 2} and SO{sub 2} levels in the gas stream lead to lower CaO conversion because of enhanced sintering and irreversible formation of CaSO{sub 4}.

01 COAL, LIGNITE, AND PEAT↗

Long-term calcination/carbonation cycling and thermal pretreatment for CO{sub 2} capture by limestone and dolomite

Capturing carbon dioxide is vital for the future of climate-friendly combustion, gasification, and steam-re-forming processes. Dry processes utilizing simple sorbents have great potential in this regard. Long-term calcination/carbonation cycling was carried out in an atmospheric-pressure thermogravimetric reactor. Although dolomite gave better capture than limestone for a limited number of cycles, the advantage declined over many cycles. Under some circumstances, decreasing the carbonation temperature increased the rate of reaction because of the interaction between equilibrium and kinetic factors. Limestone and dolomite, after being pretreated thermally at high temperatures (1000 or 1100{sup o}C), showed a substantial increase in calcium utilization over many calcination/carbonation cycles. Lengthening the pretreatment interval resulted in greater improvement. However, attrition was significantly greater for the pretreated sorbents. Greatly extending the duration of carbonation during one cycle was found to be capable of restoring the CO{sub 2} capture ability of sorbents to their original behavior, offering a possible means of countering the long-term degradation of calcium sorbents for dry capture of carbon dioxide. 12 refs., 12 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Solid looping cycles: A new technology for coal conversion

This article examines both oxygen looping cycles (otherwise known as chemical looping combustion), and lime-based CO{sub 2} looping cycles, where calcined limestone is used for in situ CO{sub 2} capture. There has been a rapid rise in the amount of research carried out recently, and both technologies are likely to see practical application in the near future. However, these technologies urgently require demonstration at the large pilot-plant level - in the case of chemical looping cycles for use with high-pressure syngas of the type likely to be produced by current coal gasification technologies and in the case of CO{sub 2} looping cycles both for combustion and gasification applications with coal. Both approaches have potential for application in schemes for H{sub 2} production, but these have not been considered here, although such applications will also inevitably follow in the medium to long term.

01 COAL, LIGNITE, AND PEAT↗