Search NASA⌕ Search

Engineering topics

Antipov, Sergey

Publications and source records attributed to Antipov, Sergey.

At least 19 records

Polished diamond X-ray lenses

High-quality bi-concave 2D focusing diamond X-ray lenses of apex-radius R = 100 µm produced via laser-ablation and improved via mechanical polishing are presented here. Both for polished and unpolished individual lenses and for stacks of ten lenses, the remaining figure errors determined using X-ray speckle tracking are shown and these results are compared with those of commercial R = 50 µm beryllium lenses that have similar focusing strength and physical aperture. For two stacks of ten diamond lenses (polished and unpolished) and a stack of eleven beryllium lenses, this paper presents measured 2D beam profiles out of focus and wire scans to obtain the beam size in the focal plane. These results are complemented with small-angle X-ray scattering (SAXS) measurements of a polished and an unpolished diamond lens. Again, this is compared with the SAXS of a beryllium lens. The polished X-ray lenses show similar figure errors to commercially available beryllium lenses. While the beam size in the focal plane is comparable to that of the beryllium lenses, the SAXS signal of the polished diamond lenses is considerably lower.

47 OTHER INSTRUMENTATION↗

An X-Band Ultra-High Gradient Photoinjector

High brightness beams appealing for XFELs and UEM essentially imply a high current and a low emittance. To obtain such beams we propose to raise the accelerating voltage in the gun mitigating repealing Coulomb forces. An ultra-high gradient is achieved utilizing a short-pulse technology. We have designed a room temperature X-band 1,5 cell gun that is able to inject 4 MeV, 100 pC bunches with as low as 0.15 mcm normalized transverse emittance. The gun is operated with as high gradients as 400 MV/m and fed by 200 MW, 10 ns RF pulses generated with Argonne Wakefield Accelerator (AWA) power extractor. We report results of low RF power tests, laser alignment test results, and successful gun conditioning results carried out at nominal RF power.

43 PARTICLE ACCELERATORS↗

High-efficiency transmission-mode diamond scintillator for quantitative characterization of X-ray beams

The luminance of a transmission mode X-ray scintillator diamond plate is dominated by induced defect centers having an excited state lifetime less than 10 msec, and in embodiments less than 1 msec, 100 usec, 10 used, 1 used, 100 nsec, or even 50 nsec, thereby providing enhanced X-ray luminance response and an X-ray flux dynamic range that is linear with X-ray flux on a log-log scale over at least three orders of magnitude. The diamond plate can be a single crystal having a dislocation density of less than 104 per square centimeter, and having surfaces that are ion milled instead of mechanically polished. The defect centers can be SiV centers induced by silicon doping during CVD diamond formation, and/or NV0 centers formed by nitrogen doping followed by applying electron beam irradiation of the diamond plate and annealing.

Antipov, Sergey↗

Cryogenic operation of planar ultrananocrystalline diamond field emission source in SRF injector

Here, we report a demonstration of electron beam generation in a superconducting radio frequency (SRF) Teraelectronvolt Energy Superconducting Linear Accelerator 1.3 GHz gun equipped with a field emission cathode and operated at 2 K. The cathode is a submicrometer film of nitrogen-incorporated ultrananocrystalline diamond [(N)UNCD] deposited atop a Nb RRR300 cathode plug that is 4 mm in diameter. Measurements of the output current showed that it increased exponentially as a function of the gun gradient. Our results demonstrate a feasible path toward simplified fully cryogenic SRF injector technology. At a maximal gradient of 0.9 MV/m, a current density of 22 μA/cm2 was obtained [calculated as a 2.75 μA current over the total cathode surface area of π(2 mm)2]. One important finding is that the electron emitter made of (N)UNCD, a material long been known as a highly efficient field emission material, demonstrated a record low turn-on gradient of 0.6 MV/m. A hypothesis explaining this behavior is proposed.

43 PARTICLE ACCELERATORS↗

Demonstration of nitrogen-incorporated ultrananocrystalline diamond photocathodes in a RF gun environment

Quantum efficiency (QE), intrinsic emittance, and robustness are the three most important figures of merit for photocathodes, the first two determine the ultimate achievable brightness of an electron beam, and the third one directly correlates with the complications of a beamline design. Nitrogen-incorporated ultrananocrystalline diamond [(N)UNCD] materials are promising candidates for photocathode applications due to their remarkable electron emission performance as well as the moderate vacuum requirement. Two (N)UNCD photocathodes have been characterized in a realistic RF gun environment with the nicely balanced performance of all three figures of merit. In this work, the QE of the first (N)UNCD cathode (stored in air for two years before the test) was found to be 3.8 x 10 –4 using a 262 nm UV laser and a cathode surface field of 30MV/m. It was found that the QE of the second (N)UNCD sample (grown days before the test) was nearly the same and, therefore, demonstrates the exceptional environmental tolerance of the material. The intrinsic emittance of (N)UNCD was measured to be 1.00 μm/mm.

36 MATERIALS SCIENCE↗

Shaped Beams from Diamond Field-Emitter Array Cathodes

Diamond field-emitter arrays (DFEAs) are arrays of diamond pyramids with exquisitely sharp tips and micrometer-scale bases that produce high current densities. These arrays can be fabricated in arbitrary shapes, ranging from single tips to many millions of tips, so that they produce an inherently shaped electron beam. Each tip emits a modest current, but the large dense array can produce many Amps. We are investigating these cathodes for use in dielectric wakefield accelerators; however, they may also be applicable to vacuum microwave tubes. Recently, shaped beam production and transport have been demonstrated in the 1.3-GHz RF gun at the Argonne Cathode Test Stand at the Argonne National Laboratory. The charge was measured on a Faraday cup and the beam imaged on a YAG screen with peak electric field gradients on the cathode ranging from 12 to 35 MV/m. Three cathode geometries were tested: one 1-mm equilateral triangle with 7-mu m base pyramids and 10-mu m pitch, one 1-mm equilateral triangle with 10-mu m base and 25-mu m pitch, and one sparse 5 x 5 square array with 20-mu m base and 400-mu m pitch. The two triangular arrays emitted 35 nC in an RF macropulse at 35 MV/m and 13-nC charge at 27 MV/m, respectively, while the sparse array emitted 0.060-nC charge at 15 MV/m. This article presents the results of the triangular array experiments, including damage due to breakdown in the RF gun and initial models of tip-to-tip shielding.

Cathodes↗

High-dynamic-range transmission-mode detection of synchrotron radiation using X-ray excited optical luminescence in diamond

Enhancement of X-ray excited optical luminescence in a 100 µm-thick diamond plate by introduction of defect states via electron beam irradiation and subsequent high-temperature annealing is demonstrated. The resulting X-ray transmission-mode scintillator features a linear response to incident photon flux in the range 7.6 × 10 8 to 1.26 × 10 12 photons s -1 mm -2 for hard X-rays (15.9 keV) using exposure times from 0.01 to 5 s. These characteristics enable a real-time transmission-mode imaging of X-ray photon flux density without disruption of X-ray instrument operation.

Instruments & Instrumentation↗

Passive method for controlling and correcting energy correlations in charged particle beams

A technique for controlling and compensating the energy spread of a charged particle beam is provided. This technique is based on a passive dielectric-loaded structure that redistributes the energy within the bunch by means of the wakefield generated in the structure. Cylindrical and planar structure configurations are provided and also means for electrical and mechanical tuning to optimize performance. The instant abstract is neither intended to define the invention disclosed in this specification nor intended to limit the scope of the invention in any way.

Simpson, James↗

Mean transverse energy of ultrananocrystalline diamond photocathode

Nitrogen incorporated ultrananocrystalline diamond [(N)UNCD] could be an enabling material platform for injector photocathode applications due to its high emissivity. While the quantum efficiency (QE) of UNCD was reported by many groups, no experimental measurements of the intrinsic emittance/mean transverse energy (MTE) have been reported. Here, MTE measurement results for an (N)UNCD photocathode in the photon energy range from 4.41 to 5.26 eV are described. The MTE demonstrates no noticeable dependence on the photon energy, with an average value of 266 meV. This spectral behavior is shown not to be dependent upon physical or chemical surface roughness and inconsistent with low electron effective mass emission from graphitic grain boundaries but may be associated with emission from spatially confined states in the grain boundaries. Lastly, the combined effect of low and constant MTE and high QE, which increases with respect to the excess laser energy, may pave the way for bright UNCD photocathodes for electron injectors.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Staging For Wakefield Acceleration Experiment Hardware Development: Fast Kicker and High Power RF Delay Section

This project pursues demonstration of the complete staging of high gradient wakefield acceleration at Argonne Wakefield Accelerator (AWA) facility, which is well aligned with the core mission of AWA and the roadmap laid out for the dielectric wakefield accelerator technology toward future linear colliders. During the project, we have successfully demonstrated the feasibility of the staged short pulse TBA (C. Jing, et al, Nucl. Instrum. Meth. A., 898, 72-76, 2018). We have successfully performed the first over 100MW dielectric power extractor. As the last task, one of the key elements for the drive beam distribution system, the fast kicker, has been built and successfully demonstrated this year too. The staging technology demonstrated in this project is crucial for the 500MeV Demonstrator that is planned at AWA in the next five years. The plan is to use two staged meter long dielectric disk accelerators to achieve 500MeV energy gain within ~10 meter long experimental space. While this SBIR project is closed, we plan to continue to investigate the dielectric accelerator technologies under Euclid's general scientific and commercial interests.

43 PARTICLE ACCELERATORS↗

High Gradient High Shunt Impedance Accelerating Structure

develop an inexpensive accelerating structure with a high gradient and high shunt impedance. Euclid Techlabs proposes to optimize this technology (based on a successful accelerating structure with distributed coupling developed at SLAC) for industrial applications and serial production. Future colliders require high gradient and high efficiency accelerating structures (high shunt impedance). The SLAC accelerator laboratory recently developed a series of accelerating structures with distributed coupling. Such a structure includes one or more parallel waveguides which are loaded by accelerating cavities. This approach allows configurations where no RF power is flowing axially through the accelerating cavity while maintaining a traveling RF wave through the cross-section of the accelerating structure. In this case the accelerating cavities are isolated at the beam pipe. Conventional traveling wave structures typically couple the RF power through the beam pipe. This feature constrains the cavity shunt impedance to relatively small values. For this reason, the distributed coupling design improves efficiency while reducing cost and improving the operational flexibility of particle accelerators. High gradient operation poses the risk of having a high breakdown rates. In traditional standing and traveling wave structures, RF power flows through the accelerating cells. For distributed coupling structures, this risk is reduced because the absence of power flow through the accelerating cavity allows configurations where no power flows through the beam pipe. Finally, the distributed coupling accelerating structure design allows fabricating structures in two halves. This significantly reduces the complexity of machining, brazing and tuning.

43 PARTICLE ACCELERATORS↗

Radiation of a charge flying in a partially loaded dielectric section of a waveguide

We consider the electromagnetic field of a point charged particle moving along the axis of a cylindrical waveguide from a homogeneously filled area to a dielectric loading area having an axially symmetrical channel. We are interested in studying the Cherenkov radiation excited in the bilayer area. The solution is performed by expanding the field in each area in a series of orthogonal eigenmodes. The main attention is focused on investigation of the wave field in the bilayer section. We show that, at a given observation point, the "reduced wakefield" is simplified with time (the number of modes decreases). The obtained results are generalized for the case of a bunch with Gaussian longitudinal profile. The typical numerical results for wakefield formation process are presented. These results agree with simulations done by the industry standard electromagnetic code CST Particle Studio.

Grigoreva, Aleksandra A.↗