Search NASA⌕ Search

Engineering topics

Antoun, Bonnie R

Publications and source records attributed to Antoun, Bonnie R.

Doped, porous iron oxide films and their optical functions and anodic photocurrents for solar water splitting

The fabrication and morphological, optical, and photoelectrochemical characterization of doped iron oxide films is presented. The complex index of refraction and absorption coefficient of polycrystalline films are determined through measurement and modeling of spectral transmission and reflection data using appropriate dispersion relations. Photoelectrochemical characterization for water photo-oxidation reveals that the conversion efficiencies of electrodes are strongly influenced by substrate temperature during their oblique-angle physical vapor deposition. These results are discussed in terms of the films' morphological features and the known optoelectronic limitations of iron oxide films for application in solar water splitting devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamic tensile characterization of a 4330-V steel with kolsky bar techniques.

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended for dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The cylindrical striker set inside the gun barrel is launched to impact on the end cap that is threaded into the open end of the gun barrel, producing a tension on the gun barrel and the incident bar.

36 MATERIALS SCIENCE↗

Dynamic tensile characterization of a 4330 steel with kolsky bar techniques.

There has been increasing demand to understand the stress-strain response as well as damage and failure mechanisms of materials under impact loading condition. Dynamic tensile characterization has been an efficient approach to acquire satisfactory information of mechanical properties including damage and failure of the materials under investigation. However, in order to obtain valid experimental data, reliable tensile experimental techniques at high strain rates are required. This includes not only precise experimental apparatus but also reliable experimental procedures and comprehensive data interpretation. Kolsky bar, originally developed by Kolsky in 1949 [1] for high-rate compressive characterization of materials, has been extended for dynamic tensile testing since 1960 [2]. In comparison to Kolsky compression bar, the experimental design of Kolsky tension bar has been much more diversified, particularly in producing high speed tensile pulses in the bars. Moreover, instead of directly sandwiching the cylindrical specimen between the bars in Kolsky bar compression bar experiments, the specimen must be firmly attached to the bar ends in Kolsky tensile bar experiments. A common method is to thread a dumbbell specimen into the ends of the incident and transmission bars. The relatively complicated striking and specimen gripping systems in Kolsky tension bar techniques often lead to disturbance in stress wave propagation in the bars, requiring appropriate interpretation of experimental data. In this study, we employed a modified Kolsky tension bar, newly developed at Sandia National Laboratories, Livermore, CA, to explore the dynamic tensile response of a 4330-V steel. The design of the new Kolsky tension bar has been presented at 2010 SEM Annual Conference [3]. Figures 1 and 2 show the actual photograph and schematic of the Kolsky tension bar, respectively. As shown in Fig. 2, the gun barrel is directly connected to the incident bar with a coupler. The cylindrical striker set inside the gun barrel is launched to impact on the end cap that is threaded into the open end of the gun barrel, producing a tension on the gun barrel and the incident bar.

36 MATERIALS SCIENCE↗

A newly developed Kolsky tension bar.

Investigation of damage and failure of materials under impact loading relies on reliable dynamic tensile experiments. A precise Kolsky tension bar is highly desirable. Based on the template of the Kolsky compression bar that we recently developed and presented at 2009 SEM conference, a new Kolsky tension bar apparatus was completed at Sandia National Laboratories, California. It is secured to the same optical table. Linear bearings with interior Frelon coating were employed to support the whole tension bar system including the bars and gun barrel. The same laser based alignment system was used to efficiently facilitate highly precise alignment of the bar system. However, the gun part was completely re-designed. One end of the gun barrel, as a part of loading device, was directly jointed to the bar system. A solid cylindrical striker is launched inside the gun barrel and then impacts on a flange attached to the other end of the gun barrel to facilitate a sudden tensile loading on the whole system. This design improves the quality of impact to easily produce a perfect stress wave and is convenient to utilize pulse shaping technique. A calibration and dynamic characterization of an aluminum specimen are presented.

36 MATERIALS SCIENCE↗

Design and implementation of coupled thermomechanical failure experiments.

Coupled thermal-mechanical experiments with well-defined, controlled boundary conditions were designed through an iterative process involving a team of experimentalists, material modelers and computational analysts. First the basic experimental premise was selected: an axisymmetric tubular specimen mechanically loaded by internal pressurization and thermally loaded asymmetrically by side radiant heating. Then several integrated experimental-analytical steps were taken to determine the experimental details. The boundary conditions were mostly thermally driven and were chosen so they could be modeled accurately; the experimental fixtures were designed to ensure that the boundary conditions were met. Preliminary, uncoupled analyses were used to size the specimen diameter, height and thickness with experimental consideration of maximum pressure loads and fixture design. Iterations of analyses and experiments were used to efficiently determine heating parameters including lamp and heating shroud design, set off distance between the lamps and shroud and between the shroud and specimen, obtainable ramp rates, and the number and spatial placement of thermocouples. The design process and the experimental implementation of the final coupled thermomechanical failure experiment design will be presented.

42 ENGINEERING↗

Coupled thermal-mechanical experiments for validation of pressurized, high temperature systems.

Instrumented, fully coupled thermal-mechanical experiments were conducted to provide validation data for finite element simulations of failure in pressurized, high temperature systems. The design and implementation of the experimental methodology is described in another paper of this conference. Experimental coupling was accomplished on tubular 304L stainless steel specimens by mechanical loading imparted by internal pressurization and thermal loading by side radiant heating. Experimental parameters, including temperature and pressurization ramp rates, maximum temperature and pressure, phasing of the thermal and mechanical loading and specimen geometry details were studied. Experiments were conducted to increasing degrees of deformation, up to and including failure. Mechanical characterization experiments of the 304L stainless steel tube material was also completed for development of a thermal elastic-plastic material constitutive model used in the finite element simulations of the validation experiments. The material was characterized in tension at a strain rate of 0.001/s from room temperature to 800 C. The tensile behavior of the tube material was found to differ substantially from 304L bar stock material, with the plasticity characteristics and strain to failure differing at every test temperature.

36 MATERIALS SCIENCE↗

Characterization of liquefied natural gas tanker steel from cryogenic to fire temperatures.

The increased demand for Liquefied Natural Gas (LNG) as a fuel source in the U.S. has prompted a study to improve our capability to predict cascading damage to LNG tankers from cryogenic spills and subsequent fire. To support this large modeling and simulation effort, a suite of experiments were conducted on two tanker steels, ABS Grade A steel and ABS Grade EH steel. A thorough and complete understanding of the mechanical behavior of the tanker steels was developed that was heretofore unavailable for the span of temperatures of interest encompassing cryogenic to fire temperatures. This was accomplished by conducting several types of experiments, including tension, notched tension and Charpy impact tests at fourteen temperatures over the range of -191 C to 800 C. Several custom fixtures and special techniques were developed for testing at the various temperatures. The experimental techniques developed and the resulting data will be presented, along with a complete description of the material behavior over the temperature span.

03 NATURAL GAS↗