Engineering topics

Antrazi, Sami S.

Publications and source records attributed to Antrazi, Sami S..

9 records

NASA NTRS1993

Adaptive control of a Stewart platform-based manipulator

A joint-space adaptive control scheme for controlling noncompliant motion of a Stewart platform-based manipulator (SPBM) was implemented in the Hardware Real-Time Emulator at Goddard Space Flight Center. The six-degrees of freedom SPBM uses two platforms and six linear actuators driven by dc motors. The adaptive control scheme is based on proportional-derivative controllers whose gains are adjusted by an adaptation law based on model reference adaptive control and Liapunov direct method. It is concluded that the adaptive control scheme provides superior tracking capability as compared to fixed-gain controllers.

Nguyen, Charles C.↗

NASA NTRS1993

Kinematics and control of a fully parallel force-reflecting hand controller for manipulator teleoperation

Design of a parallel force-reflecting hand controller that implements a friction- and inertia canceling control loop about the entire mechanism based on wrench sensing in the mechanism handgrip is discussed. Kinematics of the controller under consideration is analyzed and results are presented using a closed-form solution for the inverse kinematics and Newton-Raphson's method for the forward kinematics. Results indicate that the force control scheme based on a handgrip force sensor provides smaller steady-state errors than the scheme without a handigrip sensor.

Bryfogle, Mark D.↗

NASA NTRS1993

Testing of ROMPS robot mechanical interfaces and compliant device

The Robot Operated Materials Processing System (ROMPS) has been developed at Goddard Space Flight Center (GSFC) under a flight project to investigate commercially promising in-space material processes and to design reflyable robot automated systems to be used in the above processes for low-cost operations. The ROMPS is currently scheduled for flight in 1994 as a Hitchhiker payload in a Get Away Special (GAS) can. An important component of the ROMPS is a three degree-of-freedom (DOF) robot which will be responsible for carrying out the required tasks of in-space processing of selected materials. This report deals with testing of the mating capability of the ROMPS robot fingers with its various mechanical interfaces. In particular, the test plan will focus on studying the capability of a compliance mechanism mounted on the robot fingers in accommodating misalignments between the robot fingers and the interfaces during the mating. The report is organized as follows: Section 2 represents the main components of the ROMPS robot and briefly describes its operations. Section 3 presents the objectives of the test and outlines the test plan. The testbed comprising a Steward Platform-based high precision manipulator and associated data acquisition and control systems is described in Section 4. Section 5 presents results of numerous experiments conducted to study the mating capability of the robot fingers with its various interfaces under misalignments. The report is concluded with observations and recommendations based on the test results.

Nguyen, Charles C.↗

NASA NTRS1992

Autonomous berthing/unberthing of a Work Attachment Mechanism/Work Attachment Fixture (WAM/WAF)

Discussed here is the autonomous berthing of a Work Attachment Mechanism/Work Attachment Fixture (WAM/WAF) developed by NASA for berthing and docking applications in space. The WAM/WAF system enables fast and reliable berthing (unberthing) of space hardware. A successful operation of the WAM/WAF requires that the WAM motor velocity be precisely controlled. The operating principle and the design of the WAM/WAF is described as well as the development of a control system used to regulate the WAM motor velocity. The results of an experiment in which the WAM/WAF is used to handle an orbital replacement unit are given.

Nguyen, Charles C.↗

NASA NTRS1992

Experimental investigation of adaptive control of a parallel manipulator

The implementation of a joint-space adaptive control scheme used to control non-compliant motion of a Stewart Platform-based Manipulator (SPBM) is presented. The SPBM is used in a facility called the Hardware Real-Time Emulator (HRTE) developed at Goddard Space Flight Center to emulate space operations. The SPBM is comprised of two platforms and six linear actuators driven by DC motors, and possesses six degrees of freedom. The report briefly reviews the development of the adaptive control scheme which is composed of proportional-derivative (PD) controllers whose gains are adjusted by an adaptation law driven by the errors between the desired and actual trajectories of the SPBM actuator lengths. The derivation of the adaptation law is based on the concept of model reference adaptive control (MRAC) and Lyapunov direct method under the assumption that SPBM motion is slow as compared to the controller adaptation rate. An experimental study is conducted to evaluate the performance of the adaptive control scheme implemented to control the SPBM to track a vertical and circular paths under step changes in payload. Experimental results show that the adaptive control scheme provides superior tracking capability as compared to fixed-gain controllers.

Nguyen, Charles C.↗

NASA NTRS1992

Testing of FTS fingers and interface using a passive compliant robot manipulator

This report deals with testing of a pair of robot fingers designed for the Flight Telerobotic Servicer (FTS) to grasp a cylinder type of Orbital Replaceable Unit (ORU) interface. The report first describes the objectives of the study and then the testbed consisting of a Stewart Platform-based manipulator equipped with a passive compliant platform which also serves as a force/torque sensor. Kinematic analysis is then performed to provide a closed-form solution for the force inverse kinematics and iterative solution for the force forward kinematics using the Newton's Raphson Method. Mathematical expressions are then derived to compute force/torques applied to the FTS fingers during the mating/demating with the interface. The report then presents the three parts of the experimental study on the feasibility and characteristics of the fingers. The first part obtains data of forces applied by the fingers to the interface under various misalignments, the second part determines the maximum allowable capture angles for mating, and the third part processes and interprets the obtained force/torque data.

Nguyen, Charles C.↗

NASA NTRS1992

Analysis and experimental evaluation of a Stewart platform-based force/torque sensor

The kinematic analysis and experimentation of a force/torque sensor whose design is based on the mechanism of the Stewart Platform are discussed. Besides being used for measurement of forces/torques, the sensor also serves as a compliant platform which provides passive compliance during a robotic assembly task. It consists of two platforms, the upper compliant platform (UCP) and the lower compliant platform (LCP), coupled together through six spring-loaded pistons whose length variations are measured by six linear voltage differential transformers (LVDT) mounted along the pistons. Solutions to the forward and inverse kinematics of the force sensor are derived. Based on the known spring constant and the piston length changes, forces/torques applied to the LCP gripper are computed using vector algebra. Results of experiments conducted to evaluate the sensing capability of the force sensor are reported and discussed.

Nguyen, Charles C.↗

NASA NTRS1991

A study of space-rated connectors using a robotic end-effector

The fabrication and testing of a pair of robot fingers designed to grasp two types of Orbital Replacement Unit (ORU) interfaces, the H Handle type and the Micro Square type are discussed. A closed-form solution is given for the force inverse kinematics. A numerical solution using the Newton-Raphson Method for force forward kinematics is given. Mathematical expressions are derived to compute forces/torques applied to the finger. Suggestions are given for improving finger fabrication. The results of numerous experiments conducted to study the characteristics and feasibility of the fingers are given. The first part of the study was devoted to obtaining data on the forces applied by the finger to the interfaces under various translational and rotational misalignments; the second part was devoted to determining the maximum allowed capture angles that would insure successful mating; and the third part was devoted to the processing and interpretation of the forces/torque data.

Nguyen, Charles C.↗

NASA NTRS1991

Experimental study of trajectory planning and control of a high precision robot manipulator

The kinematic and trajectory planning is presented for a 6 DOF end-effector whose design was based on the Stewart Platform mechanism. The end-effector was used as a testbed for studying robotic assembly of NASA hardware with passive compliance. Vector analysis was employed to derive a closed-form solution for the end-effector inverse kinematic transformation. A computationally efficient numerical solution was obtained for the end-effector forward kinematic transformation using Newton-Raphson method. Three trajectory planning schemes, two for fine motion and one for gross motion, were developed for the end-effector. Experiments conducted to evaluate the performance of the trajectory planning schemes showed excellent tracking quality with minimal errors. Current activities focus on implementing the developed trajectory planning schemes on mating and demating space-rated connectors and using the compliant platform to acquire forces/torques applied on the end-effector during the assembly task.

Nguyen, Charles C.↗