Search NASA⌕ Search

Engineering topics

Arias, A.

Publications and source records attributed to Arias, A..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Effect of Yttria additives on properties of pressureless-sintered silicon nitride

Si3N4-base ceramics were made from milled Si3N4 containing 11.1 wt% SiO2 and oxide additives by pressureless sintering at 1760 C. The four-point-average moduli of rupture were 460, 515, and 515 MPa at room temperature and 270, 256, and 227 MPa at 1400 C for compositions with 3.67, 7.22, and 14.0 wt% Y2O3, respectively. The oxidation resistance of these compositions decreased with increasing Y2O3 in the 600 to 1400 C range, and no surface oxide cracking or spalling was noted. Partial substitution of Al2O3 for Y2O3 reduced both strength and oxidation resistance.

Arias, A.↗
NASA NTRS1981

Effect of CeO2, MgO and Y2O3 additions on the sinterability of a milled Si3N4 with 14.5 wt% SiO2

The sinterability of alpha Si3N4 with 0-5.07 equivalent per cent of CeO2, MgO, or Y2O3 has been studied in the temperature range 1650-1820 C by density measurements and X-ray diffraction analysis. Maximum densities were obtained in the range 1765-1820 C and were 99.6% of theoretical with 2.5% CeO2; 98.5% of theoretical with 1.24 to 1.87% MgO, and 99.2% of theoretical with 2.5% Y2O3. Densities 94% or more of theoretical value were obtained with as little as 0.62 equivalent per cent additive.

Arias, A.↗
NASA NTRS1980

Effects of oxide additions and temperature on sinterability of milled silicon nitride

Specimens of milled alpha-Si3N4 with 0 to 5.07 equivalent percent of oxide additions were pressureless sintered at 1650 to 1820 C for 4 hours in nitrogen while covered with powdered Si3N4 + SiO2. Densities of less than or equal to 97.5 percent resulted with approximately 2.5 equivalent percent of MgO, CeO2, Y2O3, and three mixtures involving these oxides. Densities of greater than or equal to 94 percent were obtained with approximately 0.62 equivalent percent of the same additives. At most temperatures, best sinterability (density maxima) was obtained with 1.2 to 2.5 equivalent percent additive.

Arias, A.↗
NASA NTRS1979

Modules of rupture and oxidation resistance of S12.55Al0.6O0.72N3.52 sialon

A Sialon of formula Si2.55Al0.6O0.72N3.52 was made from ball-milled alpha-Si3N4, AIN, and SiO2 by sintering the powder compacts at 1760 C for 4 hours in stagnant nitrogen. This Sialon had an average modulus of rupture ranging from 404 megapascals (58.6 ksi) at room temperature to 254 megapascals (36.8 ksi) at 1400 C. Oxidation tests at 1400 C in air showed it to have a parabolic oxidation rate constant less than or equal to 2.8x10 to the -10th power sq g/cm4 hr, which is smaller than that of any other Si3N4-base ceramic reported in the literature.

Arias, A.↗
NASA NTRS1979

Effect of oxygen-nitrogen ratio on sinterability of Sialons

The effect of varying the sintering temperature and the oxygen to nitrogen ratio (O/N) on the sinterability of Sialons of the formula Si2.55Al0.6OyN4-0.667y was investigated for y between 0.57 and 1.92 (O/N between 0.157 and 0.706). The Sialons reached maximum density on pressureless sintering for 4 hours at about 1760 C in nitrogen. Optimum sinterability with densities up to about 98 percent of theoretical was attained with negligible X-phase in the O/N range from about 0.2 to 0.3. On sintering at approximately 1830 C the Sialons decomposed with evolution of silicon and aluminum.

Arias, A.↗
NASA NTRS1978

Pressureless sintered Sialons with low amounts of sintering aid

Two Beta prime - Sialons of composition Si2.6Al0.393y0.007O0.4N3.6 and Si2.6Al0.384Y0.014O0.4N3.6 were pressureless sintered from mixtures of Y2O3 and separately milled Beta -Si3N4, AlN, and SiO2. These Sialons had densities of over 98% of theoretical, four-point bend strengths of 460 and 155 MPa at room temperature and 1400 C, respectively, and 1400 C oxidation rates lower than those reported for hot pressed Si3N4 and for a stronger Sialon with 2.5 weight percentage Y2O3.

Arias, A.↗
NASA NTRS1976

Metal powder reactions in ball milling

On milling chromium powder in three metal chlorides and either chromium or nickel powders in ten organic liquids representative of nine different functional groups, the powders always reacted with the liquids and became contaminated with elements from them. The milled powders had specific surface areas ranging from 0.14 to 37 sq m/g, and the total contamination with elements from the milling liquid ranged from 0.01 to 56 wt%. In most milling runs, compounds resulting from substitution, addition, or elimination reactions formed in or from the milling liquid, and in most runs with organic liquids H2, CH4, and CO2 were generated.

Arias, A.↗
NASA NTRS1976

Oxide dispersion strengthened nickel produced by nonreactive milling

It is shown that oxide dispersion strengthened alloys can be produced by a postulated nonreactive milling mechanism whereby the dispersoid is trapped at the interface between welding metal powder particles. This interparticle welding is possible because, without a suitable and sufficiently vigorous chemical reaction between the metal powder particles and the milling fluid, no protective, weld-preventing reaction coating is formed on these particles. Using water as the nonreactive milling fluid, Ni - 1.8-vol % thoria and Ni - 1.8-vol % yttria alloys with 1093 C tensile strengths ranging from 122.3 to 141.5 MN/sq m (17,900 to 20,500 psi) were produced by nonreactive milling.

Arias, A.↗
NASA NTRS1975

Production of chromium base alloys by ball milling in hydrogen iodide

The effects of processing variables on the tensile properties and ductile-to-brittle transition temperature (DBTT) of Cr + 4 vol% ThO2 alloys and of pure Cr produced by ball milling in hydrogen iodide were investigated. Hot rolled Cr + ThO2 was stronger than either hot pressed Cr + ThO2 or pure Cr at temperatures up to 1540 C. Hot pressed Cr + ThO2 had a DBTT of 500 C as compared with -8 to 24 C for the hot rolled Cr + ThO2 and with 140 C for pure Cr. It is postulated that the dispersoid in the hot rolled alloys lowers the DBTT by inhibiting recovery and recrystallization of the strained structure.

Arias, A.↗
NASA NTRS1975

Chemical reactions of metal powders with organic and inorganic liquids during ball milling

Chromium and/or nickel powders were milled in metal chlorides and in organic liquids representative of various functional groups. The powders always reacted with the liquid and became contaminated with elements from them. The milled powders had specific surface areas ranging from 0.14 to 37 sq m/g, and the total contamination with elements from the milling liquid ranged from 0.01 to 56 weight percent. Compounds resulting from substitution, addition, or elimination reactions formed in or from the milling liquid.

Arias, A.↗
NASA NTRS1974

Properties of dispersion-strengthened chromium - 4-volume-percent-thoria alloys produced by ball milling in hydrogen iodide

The effects of processing variables on the tensile properties and ductile-to-brittle transition temperature (DBTT) of Cr + 4 vol. %ThO2 alloys and of pure Cr produced by ball milling in hydrogen iodide were investigated. Hot rolled Cr + ThO2 was stronger than either hot pressed Cr + ThO2 or pure Cr at temperatures up to 1537 C. Hot pressed Cr + ThO2 had a DBTT of 501 C as compared with minus 8 to 24 C for the hot rolled Cr + ThO2 and with 139 C for pure Cr. It is postulated that the dispersoid in the hot rolled alloys lowers the DBTT by inhibiting recovery and recrystallization of the strained structure.

Arias, A.↗
NASA NTRS1973

A simplified ductile-brittle transition temperature tester

The construction and operation of a versatile, simplified bend tester is described. The tester is usable at temperatures from - 192 to 650 C in air. Features of the tester include a single test chamber for cryogenic or elevated temperatures, specimen alining support rollers, and either manual or motorized operation.

Arias, A.↗
NASA NTRS1969

Improved retort for cleaning metal powders with hydrogen

Improved cleaning retort produces uniform temperature distribution in the heated zone and minimizes hydrogen channeling through the powder bed. Retort can be used for nonmetallic powders, sintering in a reducing atmosphere, and for cleaning powders in reduction atmospheres other than hydrogen.

Arias, A.↗