Testing for Solar-Array Hotspots
Laboratory procedure developed for evaluting hot-spot endurance of photovoltaic modules under field-service conditions. Procedures used for qualification testing of modules.
Gonzalez, C. C.↗
Engineering topics
Arnett, J. C.
Publications and source records attributed to Arnett, J. C..
Candidate materials for advanced fire-resistant photovoltaic modules
A cooperative, cost-sharing research effort to develop a technology base required to construct fire-ratable photovoltaic modules has resulted in the identification of several high-temperature, back-surface candidate materials capable of raising the fire-resistance of modules using hydrocarbon encapsulants to Class A and B levels. Advanced experimental module configurations have been developed using back surfaces consisting of Kapton, Tedlar laminates, metal-foils, and fiberglass materials with high-temperature coatings. Test results (October 1984; March 1985; May 1985; and October 1985) indicate that several of these advanced module configurations are capable of achieving Class B fire-resistance levels, while a few configurations can achieve Class A levels. The paper summarizes activities to date, discussing flammability failure mechanisms, time-temperature profiles, and results of Block V environmental exposure tests of a candidate material suitable for both Class B and Class A fire-resistance levels.
Sugimura, R. S.↗
Photovoltaic module spread-of-flame testing
Photovoltaic modules used in solar energy conversion are tested for flammability. Class B burning brand tests were conducted with the following results: module glass shattered and hydrocarbon encapsulants ignited. Penetration of back surface material was the prime cause of failure. Materials with greater flame and heat resistance are under consideration to increase back surface integrity up to Class A burning brand standard. The most promising is stainless steel foil.
Sugimura, R. S.↗
Hot-spot investigations of utility scale panel configurations
The causes of array faults and efforts to mitigate their effects are examined. Research is concentrated on the panel for the 900 kw second phase of the Sacramento Municipal Utility District (SMUD) project. The panel is designed for hot spot tolerance without comprising efficiency under normal operating conditions. Series/paralleling internal to each module improves tolerance in the power quadrant to cell short or open circuits. Analtyical methods are developed for predicting worst case shade patterns and calculating the resultant cell temperature. Experiments conducted on a prototype panel support the analytical calculations.
Arnett, J. C.↗
Flammability of photovoltaic modules
A series of Class B burning-brand tests were performed on experimental modules using high-temperature, back-surface materials to develop the technology base required to construct fire-ratable modules. Results indicate the existence of synergistic relationships between hydrocarbon encapsulation materials and the experimental module configurations that provide increased fire resistance. These configurations use Kapton, fiberglass, neoprene rubber, stainless-steel foil or aluminum foil as the back surface. Successful test results occur when the structural integrity of the module back surface is maintained. Test failures of these modules always occur for one of three reasons: the outermost back cover melts, rips, or is too porous. In each case flammable molten encapsulant, its gaseous byproducts, or both, penetrates the back surface of the module and bursts into flame. Future efforts to complete the technology base will concentrate on the spread-of-flame test, focusing on the more promising configurations identified in the initial series of tests.
Sugimura, R. S.↗
Determination of hot-spot susceptibility of multistring photovoltaic modules in a central-station application
Part of the effort of the Jet Propulsion Laboratory (JPL) Flat-Plate Solar Array Project (FSA) includes a program to improve module and array reliability. A collaborative activity with industry dealing with the problem of hot-spot heating due to the shadowing of photovoltaic cells in modules and arrays containing several paralleled cell strings is described. The use of multiparallel strings in large central-station arrays introduces the likelihood of unequal current sharing and increased heating levels. Test results that relate power dissipated, current imbalance, cross-strapping frequency, and shadow configuration to hot-spot heating levels are presented. Recommendations for circuit design configurations appropriate to central-station applications that reduce the risk of hot-spot problems are offered. Guidelines are provided for developing hot-spot tests for arrays when current imbalance is a threat.
Gonzalez, C. C.↗
Evolution of integrated panel structural design and interfaces for PV power plants
The evolution of integrated photovoltaic (PV) panel design at ARCO Solar is discussed. Historically, framed PV modules of about 1 x 4-ft size were individually mounted in the field on fixed support structures and interconnected electrically with cables to build higher-power arrays. When ARCO Solar saw the opportunity in 1982 to marry its PV modules with state-of-the-art heliostat trackers developed by ARCO Power Systems, it became obvious that mounting individual modules was impractical. For this project, the framed modules were factory-assembled into panels and interconnected with cables before being mounted on the trackers. Since then, ARCO Solar made considerable progress and gained substantial experience in the design and fabrication of large PV panels. Constraints and criteria considered in these design activities included static and dynamic loads; assembly and transportation equipment and logistics, structural and electrical interfaces, and safety and grounding concerns.
Arnett, J. C.↗
Qualification testing and electrical measurement experience: A manufacturer's view
ARCO Solar's experiences as a participant in an industry-utility-government environmental qualification team examining photovoltaic devices are discussed. Included is an assessment of the applicability, completeness and appropriateness of the testing procedures and of the acceptance criteria for megawatt-sized procurements for utilities. Like the stand-alone users, the utility industry is interested in obtaining low costs, but additional concerns exist related to reliability and durability, safety, grounding and overall system criteria including performance prediction (related to output power acceptance testing), power quality and dispatchability. For purposes of this first major purchase of photovoltaic modules and panels by the utility industry, there was a carry-over of the JPL specifications. The need exists for futher development, assessement, and selection of qualification and testing standards and evaluation criteria specifically addressing these additional concerns for utility-connected PV power-plant applications.
Arnett, J. C.↗
Natural sunlight accelerated weathering of photovoltaic modules
Photovoltaic modules are exposed to the equivalent of ten years of sunlight aging in an accelerated exposure testing and evaluation program, the objective being to determine the long-term durability characteristics of flat plate modules in comparatively short periods of time. The modules are illuminated with concentrated sunlight in a large, sun-tracking, Fresnel-reflecting solar concentrator. The effects of the accelerated exposure are assessed by performing periodic visual inspections and electrical measurements. It is found that field-experienced failure modes are duplicated, that acceleration factors of 6x to 8x are readily attainable, and that the test method is feasible as a predictive tool for photovoltaic module lifetime durability.
Zerlaut, G. A.↗
Photovoltaic module hot spot durability design and test methods
As part of the Jet Propulsion Laboratory's Low-Cost Solar Array Project, the susceptibility of fat-plate modules to hot-spot problems is investigated. Hot-spot problems arise in modules when the cells become back-biased and operate in the negative-voltage quadrant, as a result of short-circuit current mismatch, cell cracking or shadowing. The details of a qualification test for determining the capability of modules of surviving field hot-spot problems and typical results of this test are presented. In addition, recommended circuit-design techniques for improving the module and array reliability with respect to hot-spot problems are presented.
Arnett, J. C.↗
Accelerated weathering of photovoltaic modules employing natural sunlight
Explore the source record for details and available documents.
Zerlaut, G. A.↗
Influence of module requirements on flat plate module design evolution
Photovoltaic module design features and performance characteristics have undergone significant evolutionary changes between pre-1975 First Generation configurations and current Third Generation design technology. A major contributor to this evolution was an iterative process of continuing design guideline and specification development for major module procurements. Module manufacturers have actively responded to these evolving requirements through progressively improving designs. This iterative/feedback process is described. Interim design guidelines and preliminary design options reflecting the LSA 1982 Module Technical Readiness Specification (November 1979) are described with respect to previous design and performance requirements.
Arnett, J. C.↗
Testing flat plate photovoltaic modules for terrestrial environment
New qualification tests have been developed for flat plate photovoltaic modules. Temperature cycling, cyclic pressure load, and humidity exposure are especially useful for detecting design and fabrication deficiencies. There is positive correlation between many of the observed field effects, such as power loss, and qualification test induced degradation. The status of research efforts for the development of test methodology for field-related problems is reviewed.
Hoffman, A. R.↗
Aseptic fluid-transfer system
Inexpensive storage and transfer system allows blood and other fluids to be added or removed without contamination. Device heat-sterilizes external surfaces of terminals and forms sterile passageway between terminals.
Arnett, J. C.↗
Thermoelectric Outer Planets Spacecraft (TOPS) electronic packaging and cabling development summary report
Electronic packaging and cabling activities performed in support of the Thermoelectric Outer Planets Spacecraft (TOPS) Advanced Systems Technology (AST) project are detailed. It describes new electronic compartment, electronic assembly, and module concepts, and a new high-density, planar interconnection technique called discrete multilayer (DML). Development and qualification of high density cabling techniques, using small gage wire and microminiature connectors, are also reported.
Dawe, R. H.↗
Side wire feed for welding apparatus
Coaxial electrode arrangement has solid central electrode, insulated outer electrode, and transverse channel for feeding wire through tip of electrode assembly. Polymeric insulation is thrust aside by pressure, which is provided by separately operated mechanism acting through central electrode.
Arnett, J. C.↗
Development of automatic through-insulation welding for microelectric interconnections
The capability to automatically route, remove insulation from, and weld small-diameter solid conductor wire is presented. This would facilitate the economical small-quantity production of complex miniature electronic assemblies. An engineering model of equipment having this capability was developed and evaluated. Whereas early work in the use of welded magnet wire interconnections was concentrated on opposed electrode systems, and generally used heat to melt the wire insulation, the present method is based on a concentric electrode system and a wire feed system which splits the insulation by application of pressure prior to welding. The work deals with the design, fabrication, and evaluation testing of an improved version of this concentric electrode system. Two different approaches to feeding the wire to the concentric electrodes were investigated. It was concluded that the process is feasible for the interconnection of complex miniature electronic assemblies.
Arnett, J. C.↗
Design feasibility study of sterile insertion techniques Final technical report
Feasibility design concepts for sterilization canister entry port
Arnett, J. C.↗