Engineering topics

Arpasi, D. J.

Publications and source records attributed to Arpasi, D. J..

At least 19 records

NASA NTRS1986

Simulating a small turboshaft engine in real-time multiprocessor simulator (RTMPS) environment

A Real-Time Multiprocessor Simulator (RTMPS) has been developed at NASA Lewis Research Center. The RTMPS uses parallel microprocessors to achieve computing speeds needed for real-time engine simulation. This report describes the use of the RTMPS system to simulate a small turboshaft engine. The process of programming the engine equations and distributing them over one, two, and four processors is discussed. Steady-state and transient results from the RTMPS simulation are compared with results from a main-frame-based simulation. Processor execution times and the associated execution time savings for the two and four processor cases are presented using actual data obtained from the RTMPS system. Included is a discussion of why the minimum achievable calculation time for the turboshaft engine model was attained using four processors. Finally, future enhancements to the RTMPS system are discussed including the development of a generalized partitioning algorithm to automatically distribute the system equations among the processors in optimum fashion.

Milner, E. J.↗

NASA NTRS1986

Development and application of dynamic simulations of a subsonic wind tunnel

Efforts are currently underway at NASA Lewis to improve and expand ground test facilities and to develop supporting technologies to meet anticipated aeropropulsion research needs. Many of these efforts have been focused on a proposed rehabilitation of the Altitude Wind Tunnel (AWT). In order to insure a technically sound design, an AWT modeling program (both analytical and physical) was initiated to provide input to the AWT final design process. This paper describes the approach taken to develop analytical, dynamic computer simulations of the AWT, and the use of these simulations as test-beds for: (1) predicting the dynamic response characteristics of the AWT, and (2) evaluating proposed AWT control concepts. Plans for developing a portable, real-time simulator for the AWT facility are also described.

Szuch, J. R.↗

NASA NTRS1986

Partitioning and packing mathematical simulation models for calculation on parallel computers

The development of multiprocessor simulations from a serial set of ordinary differential equations describing a physical system is described. Degrees of parallelism (i.e., coupling between the equations) and their impact on parallel processing are discussed. The problem of identifying computational parallelism within sets of closely coupled equations that require the exchange of current values of variables is described. A technique is presented for identifying this parallelism and for partitioning the equations for parallel solution on a multiprocessor. An algorithm which packs the equations into a minimum number of processors is also described. The results of the packing algorithm when applied to a turbojet engine model are presented in terms of processor utilization.

Arpasi, D. J.↗

NASA NTRS1986

Development and application of dynamic simulations of a subsonic wind tunnel

Efforts are currently underway at NASA Lewis to improve and expand ground test facilities and to develop supporting technologies to meet anticipated aeropropulsion research needs. Many of these efforts have been focused on a proposed rehabilitation of the Altitude Wind Tunnel (AWT). In order to insure a technically sound design, an AWT modeling program (both analytical and physical) was initiated to provide input to the AWT final design process. This paper describes the approach taken to develop analytical, dynamic computer simulations of the AWT, and the use of these simulations as test-beds for (1) predicting the dynamic response characteristics of the AWT and (2) evaluating proposed AWT control concepts. Plans for developing a portable, real-time simulator for the AWT facility are also described.

Szuch, J. R.↗

NASA NTRS1985

Real-Time Multiprocessor Programming Language (RTMPL) user's manual

A real-time multiprocessor programming language (RTMPL) has been developed to provide for high-order programming of real-time simulations on systems of distributed computers. RTMPL is a structured, engineering-oriented language. The RTMPL utility supports a variety of multiprocessor configurations and types by generating assembly language programs according to user-specified targeting information. Many programming functions are assumed by the utility (e.g., data transfer and scaling) to reduce the programming chore. This manual describes RTMPL from a user's viewpoint. Source generation, applications, utility operation, and utility output are detailed. An example simulation is generated to illustrate many RTMPL features.

Arpasi, D. J.↗

NASA NTRS1984

RTMPL: A structured programming and documentation utility for real-time multiprocessor simulations

The NASA Lewis Research Center is developing and evaluating experimental hardware and software systems to help meet future needs for real time simulations of air-breathing propulsion systems. The Real Time Multiprocessor Simulator (RTMPS) project is aimed at developing a prototype simulator system that uses multiple microprocessors to achieve the desired computing speed and accuracy at relatively low cost. Software utilities are being developed to provide engineering-level programming and interactive operation of the simulator. Two major software development efforts were undertaken in the RTMPS project. A real time multiprocessor operating system was developed to provide for interactive operation of the simulator. The second effort was aimed at developing a structured, high-level, engineering-oriented programming language and translator that would facilitate the programming of the simulator. The Real Time Multiprocessor Programming Language (RTMPL) allows the user to describe simulation tasks for each processor in a straight-forward, structured manner. The RTMPL utility acts as an assembly language programmer, translating the high-level simulation description into time-efficient assembly language code for the processors. The utility sets up all of the interfaces between the simulator hardware, firmware, and operating system.

Arpasi, D. J.↗

NASA NTRS1984

Hardware for a real-time multiprocessor simulator

The hardware for a real time multiprocessor simulator (RTMPS) developed at the NASA Lewis Research Center is described. The RTMPS is a multiple microprocessor system used to investigate the application of parallel processing concepts to real time simulation. It is designed to provide flexible data exchange paths between processors by using off the shelf microcomputer boards and minimal customized interfacing. A dedicated operator interface allows easy setup of the simulator and quick interpreting of simulation data. Simulations for the RTMPS are coded in a NASA designed real time multiprocessor language (RTMPL). This language is high level and geared to the multiprocessor environment. A real time multiprocessor operating system (RTMPOS) has also been developed that provides a user friendly operator interface. The RTMPS and supporting software are currently operational and are being evaluated at Lewis. The results of this evaluation will be used to specify the design of an optimized parallel processing system for real time simulation of dynamic systems.

Blech, R. A.↗

NASA NTRS1981

An approach to real-time simulation using parallel processing

Current applications of real-time simulations to the development of complex aircraft propulsion system controls have demonstrated the need for accurate, portable, and low-cost simulators. This paper presents a preliminary simulator design that uses a parallel computer organization to provide these features. The hardware and software for this prototype simulator are discussed. A detailed discussion of the inter-computer data transfer mechanism is also presented.

Blech, R. A.↗

NASA NTRS1981

An approach to real-time simulation using parallel processing

A preliminary simulator design that uses a parallel computer organization to provide accuracy, portability, and low cost is presented. The hardware and software for this prototype simulator are discussed. A detailed discussion of the inter-computer data transfer mechanism is also presented.

Blech, R. A.↗

NASA NTRS1979

Interactive debug program for evaluation and modification of assembly-language software

An assembly-language debug program written for the Honeywell HDC-601 and DDP-516/316 computers is described. Names and relative addressing to improve operator-machine interaction are used. Features include versatile display, on-line assembly, and improved program execution and analysis. The program is discussed from both a programmer's and an operator's standpoint. Functional diagrams are included to describe the program, and each command is illustrated.

Arpasi, D. J.↗

NASA NTRS1976

Method of discrete modeling and its application to estimation of TF30 engine variables

A method of discrete modeling is presented that effectively isolates steady state model accuracy from dynamic model accuracy. The steady state model may be generated from the engine design equations with any desired degree of accuracy. The dynamic model is generated by applying a step disturbance of a manipulated variable to an open loop engine simulation. The sampled response of the variable is combined with the steady state model's response to form a set of weighting factors. These weighting factors are then used to weight past values of the manipulated variable, thus forming the dynamic model. The method is used to estimate various TF30-P-3 engine variables. A dynamic trim function is developed to compensate for the dynamic nonlinearities of the variables as well as for inaccuracies in dynamic definition. The trim function is shown to be realted to the square root of the sum of the squares of the weighting factors obtained at various engine operating conditions. Finally, the estimation of variables without dynamic modeling is discussed.

Arpasi, D. J.↗

NASA NTRS1976

A digital computer propulsion control facility: Description of capabilities and summary of experimental program results

Flight weight digital computers are being used today to carry out many of the propulsion system control functions previously delegated exclusively to hydromechanical controllers. An operational digital computer facility for propulsion control mode studies has been used successfully in several experimental programs. This paper describes the system and some of the results concerned with engine control, inlet control, and inlet engine integrated control. Analytical designs for the digital propulsion control modes include both classical and modern/optimal techniques.

Zeller, J. R.↗

NASA NTRS1976

Description and test results of a digital supersonic propulsion system integrated control

A digitally implemented integrated inlet/engine control system was developed and tested on a mixed compression, Mach 2.5, supersonic inlet and augmented turbofan engine. The control matched engine airflow to available inlet airflow so that in steady state, the shock would be at the desired location, and the overboard bypass doors would be closed. During engine induced transients, such as augmentor lights and cutoffs, the inlet operating point was momentarily changed to a more supercritical point to minimize unstarts. The digital control also provided automatic inlet restart.

Batterton, P. G.↗

NASA NTRS1975

Design and evaluation of a sensor fail-operational control system for a digitally controlled turbofan engine

A self-learning, sensor fail-operational, control system for the TF30-P-3 afterburning turbofan engine was designed and evaluated. The sensor fail-operational control system includes a digital computer program designed to operate in conjunction with the standard TF30-P-3 bill-of-materials control. Four engine measurements and two compressor face measurements are tested. If any engine measurements are found to have failed, they are replaced by values synthesized from computer-stored information. The control system was evaluated by using a realtime, nonlinear, hybrid computer engine simulation at sea level static condition, at a typical cruise condition, and at several extreme flight conditions. Results indicate that the addition of such a system can improve the reliability of an engine digital control system.

Hrach, F. J.↗

NASA NTRS1974

Digital integrated control of a Mach 2.5 mixed-compression supersonic inlet and an augmented mixed-flow turbofan engine

A digitally implemented integrated inlet-engine control system was designed and tested on a mixed-compression, axisymmetric, Mach 2.5, supersonic inlet with 45 percent internal supersonic area contraction and a TF30-P-3 augmented turbofan engine. The control matched engine airflow to available inlet airflow. By monitoring inlet terminal shock position and over-board bypass door command, the control adjusted engine speed so that in steady state, the shock would be at the desired location and the overboard bypass doors would be closed. During engine-induced transients, such as augmentor light-off and cutoff, the inlet operating point was momentarily changed to a more supercritical point to minimize unstarts. The digital control also provided automatic inlet restart. A variable inlet throat bleed control, based on throat Mach number, provided additional inlet stability margin.

Batterton, P. G.↗

NASA NTRS1974

Self-teaching digital-computer program for fail-operational control of a turbojet engine in a sea-level test stand

The design and evaluation are described of a digital turbojet engine control which is capable of sensing catastrophic failures in either the engine rotor speed or the compressor discharge static-pressure signal and is capable of switching control modes to maintain near normal operation. The control program was developed for and tested on a turbojet engine located in a sea-level test stand. The control program is also capable of acquiring all the data that are necessary for the fail-operational control to function.

Wallhagen, R. E.↗

NASA NTRS1972

Sea-level evaluation of digitally implemented turbojet engine control functions

The standard hydromechanical control system of a turbojet engine was replaced with a digital control system that implemented the same control laws. A detailed discussion of the digital control system in use with the engine is presented. The engine was operated in a sea-level test stand. The effects of control update interval are defined, and a method for extending this interval by using digital compensation is discussed.

Arpasi, D. J.↗

NASA NTRS1972

Digital-computer normal shock position and restart control of a Mach 2.5 axisymmetric mixed-compression inlet

Digital computer control of a mixed-compression inlet is discussed. The inlet was terminated with a choked orifice at the compressor face station to dynamically simulate a turbojet engine. Inlet diffuser exit airflow disturbances were used. A digital version of a previously tested analog control system was used for both normal shock and restart control. Digital computer algorithms were derived using z-transform and finite difference methods. Using a sample rate of 1000 samples per second, the digital normal shock and restart controls essentially duplicated the inlet analog computer control results. At a sample rate of 100 samples per second, the control system performed adequately but was less stable.

Neiner, G. H.↗