Search NASA⌕ Search

Engineering topics

Artyushkova, Kateryna

Publications and source records attributed to Artyushkova, Kateryna.

At least 19 records

X-ray Photoelectron Spectroscopy Analysis of Nafion-Containing Samples: Pitfalls, Protocols, and Perceptions of Physicochemical Properties

X-ray photoelectron spectroscopy (XPS) is one of the most common techniques used to analyze the surface composition of catalysts and support materials used in polymer electrolyte membrane (PEM) fuel cells and electrolyzers, providing important insights for further improvement of their properties. Characterization of catalyst layers (CLs) is more challenging, which can be at least partially attributed to the instability of ionomer materials such as Nafion during measurements. This work explores the stability of Nafion during XPS measurements, illuminating and addressing Nafion degradation concerns. The extent of Nafion damage as a function of XPS instrumentation, measurement conditions, and sample properties was evaluated across multiple instruments. Results revealed that significant Nafion damage to the ion-conducting sulfonic acid species (>50% loss in sulfur signal) may occur in a relatively short time frame (tens of minutes) depending on the exact nature of the sample and XPS instrument. This motivated the development and validation of a multipoint XPS data acquisition protocol that minimizes Nafion damage, resulting in reliable data acquisition by avoiding significant artifacts from Nafion instability. The developed protocol was then used to analyze both thin film ionomer samples and Pt/C-based CLs. Comparison of PEM fuel cell CLs to Nafion thin films revealed several changes in Nafion spectral features attributed to charge transfer due to interaction with conductive catalyst and support species. This study provides a method to reliably characterize ionomer-containing samples, facilitating fundamental studies of the catalyst-ionomer interface and more applied investigations of structure-processing-performance correlations in PEM fuel cell and electrolyzer CLs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Editorial for the Virtual Special Issue of Journal of Power Sources “Low temperature fuel cells and electrolysers” - Science and engineering: Let's play this game hand in hand!

Electrochemistry is already and will increasingly be amongst the major drivers of our energetic mix decarbonization, so to fight anthropogenic global warming. The hydrogen economy vector (ideally produced in water electrolysers using renewable electricity and transformed back into electricity in fuel cells), in parallel with the conversion of carbon dioxide and nitrogen gas into value-added products are seen as pillars of the so-called green and sustainable Energy Revolution. The hydrogen technologies presently attract increasing interest, their momentum growing irremediably in Europe, Asia and Americas. Here, this Virtual Special Issue (VSI) gathers the latest scientific results of major research laboratories worldwide, all addressing various aspects of electrochemical energy and material conversion processes.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Catalysts by pyrolysis: Direct observation of transformations during re-pyrolysis of transition metal-nitrogen-carbon materials leading to state-of-the-art platinum group metal-free electrocatalyst

Transition metal-nitrogen-carbon (M-N-C) materials have been the focus of scientists’ efforts to address the rising need for earth-abundant materials solutions for energy technology and decarbonization of the economy. They are viewed as one of the most promising candidates to replace platinum group metal (PGM) catalysts in the fuel cell and energy conversion fields, including the application of oxygen reduction reaction, carbon dioxide reduction reaction, and nitrogen reduction reaction. In the effort to improve M-N-C materials properties and achieve atomic dispersity of the transition metal in the carbonaceous matrix, a re-pyrolysis process has been proposed. This secondary heat treatment process of already obtained primary pyrolysis-derived M-N-C materials has been widely reported to substantially improve the electrochemical performance and operational stability of the catalysts. Here, we report a systematic investigation of this process used on samples of templated M-N-C catalysts to obtain state-of-the-art catalysts via in situ heating X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD), and X-ray computed tomography (CT) characterization methods. It is found that the re-pyrolysis of M-N-C materials could result in the partial amorphization of the carbonaceous substrate. It causes the rearrangement and transformation of multitudinous N moieties, leading to optimization of their morphological display and association with atomically dispersed transition metal dopants. Ultimately, the re-pyrolysis results in an increase in uniformity of the active Fe-Nx sites distribution without the formation of nano-crystalline phases (metallic or carbide) and with overall preservation of the morphology of the carbonaceous framework achieved during the first formative pyrolysis step of the templated synthesis. Finally, these observations provide confirmation that empirically established re-pyrolysis is recommended to be used on all M-N-C materials despite the different synthesis routes to obtain a practical advanced catalytic material.

36 MATERIALS SCIENCE↗

Understanding methanol dissociative adsorption and oxidation on amorphous oxide films

Interactions between a transition metal (oxide) catalyst and a support can tailor the number and nature of active sites, for instance in the methanol oxidation reaction.In this report we use ambient pressure X-ray photoelectron spectroscopy (AP-XPS) to identify and compare the surface adsorbates that form on amorphous metal oxide films that maximize such interactions. Considering Al (1−x) M x O y (M = Fe or Mn) films at a range of methanol : oxygen gas ratios and temperatures, we find that the redox-active transition metal site (characterized by methoxy formation) dominates dissociative methanol adsorption, while basic oxygen sites (characterized by carbonate formation) play a lesser role. Product detection, however, indicates complete oxidation to carbon dioxide and water with partial oxidation products (dimethyl ether) comprising a minor species. Comparing the intensity of methoxy and hydroxyl features at a fixed XPS chemical shift suggests methanol deprotonation during adsorption in oxygen rich conditions for high transition metal content. However, increasing methanol partial pressure and lower metal site density may promote oxygen vacancy formation and the dehydroxylation pathway, supported by a nominal reduction in the oxidation state of iron sites. These findings illustrate that AP-XPS and mass spectrometry together are powerful tools in understanding metal–support interactions, quantifying and probing the nature of catalytic active sites, and considering the link between electronic structure of materials and their catalytic activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ni(OH) 2 -free NiCu as a hydrogen evolution and oxidation electrocatalyst

In this work, we investigate the role of the nickel surface oxidation and the use of additional reducing agent in the synthesis process in the electrochemical activity of NiCu electrocatalysts for hydrogen oxidation reaction and hydrogen evolution reaction. In addition, the role of the carbon support morphology is also investigated: two different supports, DENKA black and Ketjenblack with widely different properties (specific surface, proportion of low strain carbons, etc.) are studied, and no difference are observed in their electrochemical activity. However, the use 4-aminoantipyrine as a reducing agent resulted in a dramatic increase in non-oxidized Ni at the electrocatalyst’ surface, concomitant to a large increase in its activity for both the hydrogen evolution and oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Versailles Project on Advanced Materials and Standards interlaboratory study on intensity calibration for x-ray photoelectron spectroscopy instruments using low-density polyethylene

We report the results of a Versailles Project on Advanced Materials and Standards interlaboratory study on the intensity scale calibration of x-ray photoelectron spectrometers using low-density polyethylene (LDPE) as an alternative material to gold, silver, and copper. An improved set of LDPE reference spectra, corrected for different instrument geometries using a quartz-monochromated Al Kα x-ray source, was developed using data provided by participants in this study. Using these new reference spectra, a transmission function was calculated for each dataset that participants provided. When compared to a similar calibration procedure using the NPL reference spectra for gold, the LDPE intensity calibration method achieves an absolute offset of ~3.0% and a systematic deviation of ±6.5% on average across all participants. For spectra recorded at high pass energies (≥90 eV), values of absolute offset and systematic deviation are ~5.8% and ±5.7%, respectively, whereas for spectra collected at lower pass energies (<90 eV), values of absolute offset and systematic deviation are ~4.9% and ±8.8%, respectively; low pass energy spectra perform worse than the global average, in terms of systematic deviations, due to diminished count rates and signal-to-noise ratio. Differences in absolute offset are attributed to the surface roughness of the LDPE induced by sample preparation. We further assess the usability of LDPE as a secondary reference material and comment on its performance in the presence of issues such as variable dark noise, x-ray warm up times, inaccuracy at low count rates, and underlying spectrometer problems. In response to participant feedback and the results of the study, we provide an updated LDPE intensity calibration protocol to address the issues highlighted in the interlaboratory study. Finally, we also comment on the lack of implementation of a consistent and traceable intensity calibration method across the community of x-ray photoelectron spectroscopy (XPS) users and, therefore, propose a route to achieving this with the assistance of instrument manufacturers, metrology laboratories, and experts leading to an international standard for XPS intensity scale calibration.

36 MATERIALS SCIENCE↗

Graphite Intercalation Compounds Derived by Green Chemistry as Oxygen Reduction Reaction Catalysts

Precious group metal (PGM) catalysts such as Pt supported on carbon supports are expensive catalysts utilized for the oxygen reduction reaction (ORR) due to their unmatched catalytic activity and durability. As an alternative, PGM-free ORR electrocatalysts that offer respectable catalytic activity are being pursued. Most of the notable PGM-free catalysts are obtained either from a bottom-up approach synthesis utilizing nitrogen-rich polymers as building blocks, or from a top down approach, where nitrogen and metal moieties are incorporated to carbonaceous matrixes. The systematic understanding of the origin of catalytic activity for either case is speculative and currently employed synthesis techniques typically generate large amounts of hazardous waste such as acids, oxidizing agents, and solvents. Herein, for the first time, we investigate the catalytic activity of graphite-based materials obtained via intercalation strategies that minimally perturb the graphitic backbone. Here, our outlined approaches demonstrate initial efforts to not only elucidate the role of each element but also significantly reduce the use of hazardous chemicals, which remains a pressing challenge. Graphite intercalation compounds (GIC) were obtained using fewer steps and solvent-free processes. X-ray diffraction and Raman results confirm the successful intercalation of FeCl 3 between graphite layers. Electrochemical data shows that the ORR performance of FeCl 3 -intercalated GIC displays slight improvement where the onset potential reaches 0.77 V vs RHE in alkaline environments. However, expansion of the graphite and solvent-free incorporation of iron and nitrogen moieties resulted in a significant increase in ORR activity with onset potential to 0.89 V vs RHE, a maximum half-wave of 0.72 V vs RHE, and a limiting current of about 2.5 mA cm –2 . We anticipate that the use of near solvent-free processes that result in a high yield of catalysts along with the fundamental insight into the origin of electrochemical activity will tremendously impact the methodologies for developing next-generation ORR catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizing Complex Gas–Solid Interfaces with in Situ Spectroscopy: Oxygen Adsorption Behavior on Fe–N–C Catalysts

Electrocatalysts for the oxygen reduction reaction within polymer electrolyte membrane fuel cells based on iron, nitrogen, and carbon elements (Fe–N–C) are receiving significant research attention as they offer an inexpensive alternative to catalysts based on platinum-group metals. Although both the performance and the fundamental understanding of Fe–N–C catalysts have improved over the past decade, there remains a need to differentiate the relative activity of different active sites. Toward this goal, our study is focused on characterizing the interactions between O 2 and a set of five structurally different Fe–N–C materials. Detailed characterization of the Fe speciation was performed with 57 Fe Mössbauer spectroscopy and soft X-ray absorption spectroscopy of the Fe L 3,2 -edge, whereas nitrogen chemical states were investigated with X-ray photoelectron spectroscopy (XPS). In addition to initial sXAS and XPS measurements performed in ultra-high vacuum (UHV), measurements were also performed (at the identical location) in an atmosphere of 100 mTorr of O 2 at 80 °C (O 2 -rich). XPS and sXAS results reveal the presence of several types of FeNxCy adsorption sites. FeNxCy sites that are proposed as the most active ones do not show significant change (based on the techniques used in this study) when their environment is changed from UHV to O 2 -rich. Correlation with Mössbauer and sXAS results suggests that this is most likely due to the persistence of strongly adsorbed O 2 molecules from their previous exposure to air. However, other species do show spectroscopic changes from UHV conditions to O 2 -rich. This implies that these sites have a weaker interaction with O 2 that results in their desorption in vacuum conditions and re-adsorption when exposed to the O 2 -rich environment. The nature of these weakly and strongly O 2 -adsorbing FeN x C y sites is discussed in the context of different synthetic and processing parameters employed to fabricate each of these five Fe–N–C materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

XPS guide: Charge neutralization and binding energy referencing for insulating samples

This guide deals with methods to control surface charging during XPS analysis of insulating samples and approaches to extracting useful binding energy information. Furthermore, the guide summarizes the causes of surface charging, how to recognize when it occurs, approaches to minimize charge buildup, and methods used to adjust or correct XPS photoelectron binding energies when charge control systems are used. Additionally, there are multiple ways to control surface charge buildup during XPS measurements and examples of systems on advanced XPS instruments are described. There is no single, simple, and foolproof way to extract binding energies on insulating material, but advantages and limitations of several approaches are described. Because of the variety of approaches and limitations of each it is critical for researchers to accurately describe the procedures that have been applied in research reports and publications.

47 OTHER INSTRUMENTATION↗

Proliferation of Faulty Materials Data Analysis in the Literature

As a group of subject matter experts in X-ray photoelectron spectroscopy (XPS), we write this letter to raise awareness of the epidemic of poor and incorrect materials data analysis in the Literature. This is a chronic and growing problem with very undesirable consequences. This issue may contribute to what has been identified as a “reproducibility crisis”1,2 that was the subject of a recent U.S. National Academies study. We are using XPS as one example of what we observe to be a systemic issue.

36 MATERIALS SCIENCE↗

Understanding Surface Reactivity of Amorphous Transition-Metal-Incorporated Aluminum Oxide Thin Films

The electronic structure of multi-metal, amorphous oxides, can be varied across a wide range of elemental compositions. Bulk properties such as conductivity, work function, and absorption can thus be tailored to suit a range of applications spanning from carrier-selective contacts to catalysis. Missing, however, is an understanding of how the surface reactivity is impacted in mixed metal-oxide amorphous films. Here we investigate the propensity of Al(1-x)M(x)Oy (M = Fe, Mn) amorphous oxide films to dissociate water into hydroxyl groups in a humid environment, and find comparable hydroxylation at the low relative humidity (~0.3% RH) probed by ambient pressure X-ray photoelectron spectroscopy. In contrast, films with both Al and Fe show an increased formation of methoxy groups upon methanol exposure compared to pure Al- and Fe-oxide end members, indicating the coordination environment of the amorphous oxide network impacts the acidity and redox character of surface metal and oxygen sites. These results provide guidance for the rational design of amorphous oxide layers with tailored chemical reactivity or passivity for a given application.

Stoerzinger, Kelsey A.↗

Investigating the Nature of the Active Sites for the CO 2 Reduction Reaction on Carbon-Based Electrocatalysts

To achieve a better understanding of the CO 2 reduction reaction on carbon-based electrocatalysts, we synthesized a library of nitrogen-doped carbonaceous materials with atomically dispersed 3d transition metals and corresponding metal-free electrocatalysts. The sacrificial support method was used yielding catalyst materials of high dispersity and high graphitic content. The resulting electrocatalysts were impurity free, hence allowing a better understanding of the mechanism of CO 2 reduction. By combining the electrochemical results with density functional theory, we were able to separate the electrocatalysts into several categories, based on their CO 2 → COOH ads free energy and their CO ads binding strength. The “strong-CO binder” electrocatalysts (e.g., Cr, Mn and Fe–N–C) achieved a Faradaic efficiency up to 50% at –0.35 V vs. RHE (at pH = 7.5, in 0.1 M phosphate buffer). Such Faradaic efficiency was also achieved for a metal-free electrocatalyst, therefore showing the high activity of the metal-free, N-containing, moieties toward the CO 2 reduction reaction. Furthermore, this was confirmed by near ambient pressure X-ray photoelectron spectroscopy that confirmed pyridinic and hydrogenated (pyrrolic) nitrogen moieties act as preferential adsorption sites for the CO 2 on the Fe–N–C catalyst surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

PGM-Free ORR Catalysts Designed by Templating PANI-Type Polymers Containing Functional Groups with High Affinity to Iron

In this work, a coordination-chemistry approach was used to increase the content of nitrogen-coordinated iron moieties (Fe-N x ) in platinum group metal-free (PGM-free) catalysts for oxygen reduction reaction (ORR). The catalysts were derived from a series of polyaniline (PANI)-type precursors with N-containing functional side chains having high affinity to iron. The PGM-free ORR catalysts synthesized using such polymeric templates were characterized by scanning electron microscopy, X-ray diffractometry, and tested in an electrochemical cell and H 2 -air fuel cell for ORR activity. X-ray photoelectron spectroscopy (XPS) analysis showed that, in spite of similar nitrogen contents, catalysts obtained using PANI-type polymers containing side chains with high affinity to iron had higher Fe content than PANI-derived catalyst. These PGM-free catalysts showed improved ORR activity in an electrochemical cell and in H 2 -air fuel cell testing, compared to the PANI-derived catalyst. A correlation between the content of Fe-N x moieties and the fuel cell performance was observed in these PGM-free ORR catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Practical guides for x-ray photoelectron spectroscopy: First steps in planning, conducting, and reporting XPS measurements

Over the past three decade the use of XPS in research and publications has grown to make XPS the most widely used surface analysis method. Associated with the increased use there is an increase in new or inexperienced users along with a increase in erroneous and misapplications of the method. This article is the first in a series of guides and tutorials assembled by a committee of experienced practitioners intended to assist inexperienced users by sharing information about good practices in the use of XPS. This first guide identifies some sources of information for learning how to conduct XPS studies and examines the types of questions to be asked when determining if XPS is an appropriate technique to provide the needed or desired information. Many of the topics/questions addressed in this article apply to the other surface analysis techniques as well.

47 OTHER INSTRUMENTATION↗

Experimental and Theoretical Trends of PGM-Free Electrocatalysts for the Oxygen Reduction Reaction with Different Transition Metals

Replacement of platinum-based electrocatalysts to facilitate the oxygen reduction reaction (ORR) in proton exchange fuel cells remains an outstanding challenge. Significant progress in the development of platinum group metal-free (PGM-free) electrocatalysts has been reported but a fundamental understanding of how these materials catalyze the ORR remains elusive. In this work, we report our efforts to synthesize and characterize PGM-free electrocatalysts with different transition metals (M = Fe, Co, and Mn) in order to better understand the most plausible active site structures and ORR reaction pathways. Our findings indicate that PGM-free electrocatalysts synthesized via a dual nitrogen precursor, polyaniline and cyanamide, synthesis process but with varied transition metal precursors resulted in the following ORR activity trend: Fe > Co > Mn. Furthermore, similar densities of active sites across the three synthesized materials were calculated using an established molecular probe technique. The relative experimental activities are consistent with trends determined via density functional theory (DFT) modeling that suggests spontaneous OH ligand modification of active sites.

25 ENERGY STORAGE↗

Characterization of Complex Interactions at the Gas–Solid Interface with in Situ Spectroscopy: The Case of Nitrogen-Functionalized Carbon

Interactions at the gas-solid interface drive physicochemical processes in many energy and environmental applications; yet, the challenges associated with characterization and development of these dynamic interactions in complex systems limit progress in developing effective materials. Thus, structure-property-performance correlations greatly depend on the development of advanced techniques and analysis methods for the investigation of gas-solid interactions. In this work, adsorption behavior of O 2 and humidified O 2 on nitrogen-functionalized carbon (N-C) materials was investigated to provide a better understanding of the role of nitrogen species in the oxygen reduction reaction (ORR). N-C materials were produced by solvothermal synthesis and N-ion implantation, resulting in a set of materials with varied nitrogen amount and speciation in carbon matrices with different morphologies. Adsorption behavior of the N-C samples was characterized by in situ diffuse reflectance infrared Fourier-transform spectroscopy (DRIFTS) and ambient pressure X-ray photoelectron spectroscopy (AP-XPS) experiments. A novel analysis approach for the interpretation of AP-XPS data was developed, allowing both the determination of overall adsorption behavior of each N-C material and identification of which nitrogen species were responsible for adsorption. The complementary information provided by in situ DRIFTS and AP-XPS suggests that O 2 adsorption primarily takes place on either electron-rich nitrogen species like pyridine, hydrogenated nitrogen species, or graphitic nitrogen. Adsorption of O 2 and H 2 O occurs competitively on solvothermally prepared N-Cs, whereas adsorption of H 2 O and O 2 occurs at different sites on N-ion implanted N-Cs, highlighting the importance of tuning the composition of N-C materials to promote the most efficient ORR pathway.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗