Engineering topics

Arulanandam, Madhan K.

Publications and source records attributed to Arulanandam, Madhan K..

5 records

DOE OSTI2024

Patterned dielectric back contact design for GaAs thermophotovoltaic devices

-Patterned-dielectric back contact structures in optoelectronic devices are designed to boost the reflectance of light from the device back surface while retaining a low-resistance pathway for electrical conductance. Their reduced light absorption at near- and sub-bandgap photon energies leads to improved luminescence in light-emitting diodes, greater photon recycling, voltage, and efficiency in photovoltaic cells, and greater recuperation of unabsorbed sub-bandgap light in thermophotovoltaic (TPV) systems. However, diffraction from the patterned features can deflect incident light in propagation directions that lead to light trapping and parasitic absorption in the cell. Here, in this article, we use rigorous coupled-wave analysis (RCWA) to study three-dimensional diffractive scattering of electromagnetic waves by periodic metal point-contact gratings on 1.42-eV GaAs TPV cells, to analyze their effect on unwanted sub-bandgap absorption in order to achieve higher TPV system efficiency. Solutions of Maxwell's equations calculated using RCWA are compared to measured sub-bandgap reflectance in experimental GaAs TPV devices with varying metal point-contact diameters and spacing. Modeling and experiments indicate decreased total reflectance due to these diffractive effects for a small point contact diameter of 1 μm, and this effect is much stronger at higher contact coverage fractions.

14 SOLAR ENERGY↗

DOE OSTI2022

Efficient and scalable GaInAs thermophotovoltaic devices

We report thermophotovoltaics are promising solid-state energy converters for a variety of applications such as grid-scale energy storage, concentrating solar-thermal power, and waste-heat recovery. Here, we report the design, fabrication, and testing of large area (0.8 cm 2 ), scalable, single-junction 0.75-eV GaInAs thermophotovoltaic devices reaching an efficiency of 38.8% +/- 2.0% and an electrical power density of 3.78 W/cm 2 at an emitter temperature of 1,850 °C. Reaching such a high emitter temperature and power density without sacrificing efficiency is a direct result of combining good spectral management with an optimized cell architecture, excellent material quality, and low series resistance. Importantly, fabrication of 12 high-performing devices on a 2-in wafer is shown to be repeatable, and the cell design can be readily transferred to commercial epitaxy on even larger wafers. Further improvements in efficiency can be obtained by using a multijunction architecture, illustrated by early results for a two-junction 0.84-eV GaInPAs/0.75-eV GaInAs device.

14 SOLAR ENERGY↗

DOE OSTI2022

GaAs Thermophotovoltaic Patterned Dielectric Back Contact Devices with Improved Sub-Bandgap Reflectance

We demonstrate GaAs thermophotovoltaic (TPV) devices with a patterned dielectric back contact (PDBC) architecture, featuring a dielectric spacer between the semiconductor and back metal contact over most of the back surface for high reflectance, and metal point contacts over a smaller area for electrical conduction. In the TPV application, high sub-bandgap reflectance is needed to reflect unused sub-bandgap photons to the thermal emitter to minimize energy losses in this portion of the thermal spectrum. We explore different PDBC fabrication processes with SU-8 and SiO2 dielectric spacer layers to maximize sub-bandgap reflectance while minimizing series resistance to increase TPV conversion efficiency. We successfully demonstrate GaAs SU-8 PDBC TPV devices with 2200 degrees C blackbody-weighted sub-bandgap reflectance of 94.9% and 96.5% with and without a front metal grid, respectively. This is 0.7% and 2.3% (absolute) higher than the mean sub-bandgap reflectance of 94.2% for GaAs baseline TPV devices with 100% Au back contact with front metal grid. Lower sub-bandgap reflectance in TPV devices with front grids indicates the front grid induces light scattering leading to additional parasitic absorption in the TPV device. We also show that for higher contact coverage fractions, the PDBC reflectance cannot in general be treated by a linear interpolation using simple 1D transfer matrix method modeling and should be treated instead as a diffraction grating by solving Maxwell's equations in 3D.

energy storage↗

DOE OSTI2021

Platform for Accurate Efficiency Quantification of > 35% Efficient Thermophotovoltaic Cells

Thermophotovoltaic (TPV) devices convert thermal radiation directly into electricity using semiconductor diodes and have a variety of uses from waste heat recovery to energy storage to primary power conversion. Recent results have demonstrated promising cells nearing and surpassing 30% conversion efficiency. As TPV cells continue to increase in efficiency, they become attractive for a wider range of applications. Their efficiencies must be quantified in a standardized fashion to compare results accurately across research groups. Here, we outline and quantify the most important characteristics of an accurate and precise TPV efficiency measurement. Using a custom-built measurement apparatus that takes these characteristics into account, we report 19 cells with greater than 30% conversion efficiency and 2 cells with greater than 35% conversion efficiency. This confirms that our reported cell efficiencies are not simply those of hero cells but rather of a distribution of cells that can be produced in a consistent, high-quality process.

III-V↗

DOE OSTI2021

World Record Demonstration of > 30% Thermophotovoltaic Conversion Efficiency

Thermophotovoltaic (TPV) devices are solid-state heat engines that convert thermal radiation into electricity using semiconductor diodes, and have applications in energy storage, primary power conversion, and waste heat recovery. Higher temperature emitters and wider band gap photovoltaics (PVs) generally afford higher TPV efficiencies. High temperature emitters are accessible in thermal energy storage applications. We have demonstrated a world record 31% +/- 2% TPV conversion efficiency with a 0.9 cm2 GaAs-based PV device under a 2430 °C thermal emitter, producing an electrical output power of 2.23 W. Critical to the result was the cell’s high reflectance of photon energies below the device band gap. Unlike solar PV, for which sub-band gap (SBG) light is lost, a TPV cell can reflect and recycle SBG light to the thermal emitter. The demonstration was made on a custom-built measurement platform in which a ~100 cm2 graphite thermal emitter was heated under vacuum up to 2430 °C. The TPV efficiency was evaluated by comparing the measured electrical output power of the TPV with the calorimetrically measured total net power incident on the cell. The measured TPV efficiency as a function of thermal emitter temperature was corroborated by our full system modeling predictions. As far as the authors are aware, this is the highest TPV conversion efficiency ever measured, and device improvements should yield > 40% efficiency in the near future.

27 ARPA - Advanced Research Projects Agency-Energy↗