Engineering topics

Ashtijou, Mohammad

Publications and source records attributed to Ashtijou, Mohammad.

4 records

NASA NTRS2020

Select Electronic Parts Operation at Extreme Low Temperature

The purpose of the study presented in this paper is to extend the test period of a selected set of electronics parts at cryogenic condition to dwell period of about 24 hours to demonstrate extreme cold operational capability of these components. The parts tested are tantalum polymer, BX and P90 type ceramic capacitors, thick film resistors, analog multiplexers, a digital inverter, and a D-flip-flop. These parts were tested to assist identifying candidate components that can be used for development of a cold capable telemetry board. There are several past investigations that have shown that COTS (commercial-off-the-shelf) capacitors and resistors tested at cryogenic temperatures and frequencies up to 10MHz did not exhibit significant changes in capacitance and resistance values. Also, there are several test results for active parts. These past tests collected measurements during a temperature sweep from room temperature down to cryogenic temperature with very short dwell time at cryogenic temperature, and back to room temperature. This study extends the operational dwell time to at least 24 hours and returning to room temperature operation without significant degradation in performance, thus, demonstrating the potential for longer dwell time in actual operation in these extreme cold temperatures and a method for identifying the cold operability.

Ashtijou, Mohammad↗

NASA NTRS2018

Evaluation of Commercial-Off-The-Shelf (COTS) Electronics for Extreme Cold Environments

Deep space and Icy Moon missions (Titan, Enceladus, Ceres, Europa, & Ganymede) will need qualified extreme environment capable components for electronic systems located in extremities of their rovers and spacecraft. Commercial off the shelf (COTS) components would be advantageous to use for some aspects of such projects, given that they are easier to procure and offer a broad range of functionalities. Furthermore, theoretical and experimental data suggest that many COTS parts are capable of operation, and not just storage, at temperatures well beyond the manufacturer specified temperature limits. To help address the challenges presented at near cryogenic temperatures, a COTS selection knowledge base is being developed to estimate the performance of COTS components within cold environments. The knowledge base captures queries from a range of information sources such as cold functionality test results for part types and families, theoretical and experimental literature reviews and key findings are summarized here. In addition, a selection of components are planned to be examined for their performance to near cryogenic temperatures to generate a methodology for identification and verification of the COTS candidates. As the qualification of COTS parts for extreme environments can be very costly, this knowledge base can serve to reduce qualification time and cost by pre-selecting and limiting candidates.

Mojarradi, Mohammad↗

NASA NTRS2016

M2020/MSL: TDS (Terminal Descent Sensor) DEA (Digital Electronics Assembly)

TDS is the radar used in MSL mission to land Curiosity rover on Mars. TDS will be used again in M2020 mission. DEA is the brain of the TDS where it serves as the controller and digital signal processor. The DEA commands TDS to cycle through the antenna beams making measurements using one of the 6 antenna beams at a time. DEA uses beam sequences and parameter tables to generate measurements. The most important measurements are velocity and range that are used to guide the landing of Curiosity rover. DEA performs these measurement tasks using radar signal processing FPGA firmware and radar microprocessor ‘s hardware and software.

Ashtijou, Mohammad↗

NASA NTRS2006

Micro-Inspector Avionics Module (MAM): A Self-Contained Low Power, Reconfigurable Avionics Platform for Small Spacecrafts and Instruments

This paper describes development of a radiation tolerant, low power, reconfigurable avionics module aimed at meeting the avionics needs of the JPL Micro-Inspector spacecraft. This module represents a complete avionics system, consisting of two PowerPC 405 CPUs embedded within a reconfigurable FPGA fabric of over 8 Million logic gates, 64MB of EDAC protected Flash storage and 128MB of EDAC protected DDR SDRAM or SDRAM memories, along with FPGA SEU mitigation logic, and all necessary power conversion. Processor SEU mitigation is achieved by running the two processors in a lock-step and compare configuration. All of these building blocks are integrated into a double sided circuit board that takes as little as 6 square inches of board space. This module can be embedded into a user system as part of a bigger circuit assembly or as a self contained module. This module is being developed as part of a JPL led Micro-Inspector Program, funded by NASA ESMD aimed at producing a 10Kg micro spacecraft.

configurable↗