Search NASA⌕ Search

Engineering topics

Asmussen, Susan E.

Publications and source records attributed to Asmussen, Susan E..

The effect of cerium, neodymium, and ytterbium doping on UO 2 dissolution

Here, the dissolution rate of spent nuclear fuel has been studied heavily to understand the impacts of a failed waste package scenario on potential radionuclide release from a geologic repository. Multiple countries have evaluated these scenarios in oxidizing and reducing environments respective to their relevant repository conditions. The repository environment (e.g., water chemistry, temperature, oxygen content) and the fuel itself (e.g., chemical content of the fuel) both heavily impact the dissolution rate of the spent fuel. This work examined the impact that rare earth element dopants (Ce, Nd, Yb) have on the fuel dissolution under repository relevant conditions with decreasing oxidizing conditions using a single pass flowthrough system. UO 2 samples were doped with Ce, Nd, or Yb with concentrations between 1 and 5 at%. The addition of dopants to the samples reduced the dissolution rates on most samples relative to pure UO 2 samples. Scoping experiments that occurred in a less oxidizing environment showed a reduction in dissolution rate compared to fully oxidizing conditions. The results within highlight the importance of dopant behavior in used fuel dissolution modeling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

PNNL FY 2022 Sibling Pin Testing Results

This report presents the results of testing two rods after heat treatment at 400C for 8 hours and compares to the results from FY 2021 of similar rods that were tested as baseline. The heat treatment resulted in a decrease in yield stress.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

PNNL FY2021 Sibling Pin Testing Results

The post-irradiation examination, axial tensile, burst, and four-point bend testing results of the first two sibling pins, 6U3/L8 and 5K7/P2 are presented.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Measurement of Iodine, Iodide, and Iodate in Hanford Tank Waste: Technology Transfer from PNNL to Hanford 222-S Laboratory

This report summarizes the measurement of the inorganic chemical forms of iodine in Hanford tank waste. The Hanford tank wastes have roughly a part per million iodine. Part of the iodine is the long-lived beta emitter 129I, and the rest is stable 127I. Because tank waste iodine is radioactive and radiotoxic, its chemical form must be known so that its behavior in the vitrification process can be reliably known and anticipated in various waste streams (glass, secondary liquid and solid waste, and offgas emissions) at Hanford. Iodine in tank wastes exists in the inorganic chemical forms iodide and iodate (and possibly also periodate) and also as organic forms such as alkyl iodides. The measurement of organic iodides is very different from the measurement of inorganic forms and is outside the scope of this report. The inorganic chemical forms are chemically separated, in sequence, from the raw tank waste using solvent extractions and several redox reactions, then measured by ICP-MS. The inorganic chemical forms of iodine are chemically reactive, and so is the tank waste. The chemistry must be carefully designed to avoid unintended reactions that could convert one form of iodine to another during the analysis, which would skew the data and report iodine in the wrong chemical form. This iodine analysis, developed at PNNL, is being transferred to the DOE 222-S Laboratory on the Hanford Site, in Washington State, for implementation during waste processing operations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Optical Spectroscopic Investigation of Hexavalent Actinide Ions in n-Dodecane Solutions of Tri-butyl Phosphate

The extraction of hexavalent actinides An(VI) by tri-butyl phosphate (TBP) was investigated by electronic absorption and vibrational spectroscopies. Through a series of spectral subtractions, vibrational spectra associated with TBP, TBP–HNO3 adducts, and An(VI)–TBP complexes could be isolated. Investigation of U(VI) extracts indicated spectral features consistent with the formation of the expected [UO2(NO3)2(TBP)2] complex, but spectral features of other species were clearly evident. Likewise, multiple species were evident in the electronic absorption and vibrational spectra of TBP phases generated by extraction of Pu(VI). Although definitive characterization of the additional species formed could not be achieved in this work, it is hypothesized that they contain 3:1 TBP-to-An(VI) stoichiometry.

Lumetta, Gregg J.↗

CoDCon Project (Final Report)

The co-decontamination (CoDCon) project was established in FY 2016 with the objectives of (a) evaluating the uncertainty in the uranium (U)/plutonium (Pu) ratio in a mixed U/Pu product from a tributyl phosphate (TBP)–based solvent extraction flowsheet, and (b) developing and demonstrating on-line optical spectroscopy for real-time monitoring of key components (e.g., Pu, U, and HNO 3 concentrations) in the process solutions. We were interested in assessing the accuracy and precision to which a specific uranium-to-plutonium (U/Pu) ratio can be achieved, which for the purposes of this project was set at a U/Pu mass ratio of 7/3. The uncertainty associated with achieving this specific target U/Pu ratio was investigated during five flowsheet tests using laboratory-scale solvent extraction equipment. In addition, optical spectroscopic techniques were incorporated into the CoDCon solvent extraction testing system, allowing real time monitoring of all input and output process streams. Two CoDCon flowsheet tests were performed in FY 2018 using a simple dissolved fuel simulant containing only U (~1 M) and Pu (~15 mM) in nitric acid (HNO 3 ; ~3 M). In FY 2019, two additional flowsheet tests were performed. For the first of these (CoDCon Run 3), the dissolved fuel simulant was similar to that used in the first two tests, with the inclusion of 1 mM neptunium (Np). The second test conducted in FY 2019 (CoDCon Run 4) used a more representative dissolved fuel simulant, including addition of non-radioactive fission product elements. A fifth CoDCon flowsheet test (CoDCon Run 5) was conducted in FY 2020, with the following additional objectives: (1) routing of the technetium (Tc) in the simulated dissolved fuel solution to the solvent extraction raffinate, and (2) routing of the Np in the simulated dissolved fuel solution to the U/Pu product. All tests used a bank of sixteen 2 cm centrifugal contactors. The tests involved first loading the solvent (30 vol% TBP dissolved in n-dodecane) with U and Pu (and Np, for Run 5), then the Pu (and Np) was stripped from the loaded solvent with a U(IV) solution (~50 mM) and the flowsheet conditions were adjusted such that some U partitioned into the Pu-containing product stream. The amount of U accompanying the Pu was monitored in real time using optical spectroscopic techniques coupled with chemometric modeling. Based on the real-time spectroscopic measurement of the U/Pu ratio, adjustments were made to the flowrate of the fresh TBP solvent phase used to scrub U from the aqueous Pu-containing product. This proved to be a very effective way to control the U/Pu mass ratio in the product. This report presents the results of the CoDCon Run 5 test. The flowsheet tested in Run 5 was substantially different than that run in the prior tests, especially the solvent loading section of the flowsheet. Two key changes were made. First, based on the objective to extract all the Np and route it with the U/Pu product, pentavalent vanadium [V(V)] was added to the feed and scrub solutions. The purpose of the V(V) was to convert all the Np to the +6 oxidation state, which is extractable by TBP. Second, a high acid (8 M HNO 3 ) scrub was added to the flowsheet to scrub the Tc from the solvent. This was followed by a low acid scrub (0.05 M HNO 3 ) to reduce the residual HNO 3 concentration in the solvent prior to the Pu stripping step. The output from the low acid scrub was collected separately, rather than routing towards the raffinate. The modifications to the solvent loading part of the flowsheet were only partially successful. The treatment with V(V) was effective at converting the Np to Np(VI). Only 1.3% of the Np remained in the raffinate solution. However, ~40% of the Np stripped out of the solvent in the low acid scrub step; nearly 20% of the Pu also was stripped from the solvent during the low acid scrub. For further development, either modifications to the flowsheet, or concentration and recycle of the low acid stream into the

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

CoDCon Project: FY 2019 Status Report

The co-decontamination (CoDCon) project was established in FY 2016 with the objectives of (a) evaluating the uncertainty in the uranium (U)/plutonium (Pu) ratio in a mixed U/Pu product from a tributyl phosphate (TBP)–based solvent extraction flowsheet and (b) developing and demonstrating on-line optical spectroscopy for real-time monitoring of key components (e.g., Pu, U, and HNO 3 concentrations) in the process solutions. We are interested in establishing the accuracy and precision to which a specific uranium-to-plutonium (U/Pu) ratio can be achieved, which for the purposes of this project is set at a U/Pu mass ratio of 7/3. The uncertainty associated with achieving this specific target U/Pu ratio is being established through multiple flowsheet tests using laboratory-scale solvent extraction equipment. In addition, optical spectroscopic techniques have been incorporated into the CoDCon solvent extraction testing system, allowing real time monitoring of all input and output process streams. Two CoDCon flowsheet tests were successfully performed in FY 2018. In FY 2019, two additional flowsheet tests were performed. For the first of these (CoDCon Run 3), the dissolved fuel simulant was similar to that used in the first two tests, with the inclusion of 1 mM neptunium (Np). The second test conducted in FY 2019 (CoDCon Run 4) used a more representative dissolved fuel simulant, including addition of non-radioactive fission product elements. All tests used a bank of sixteen 2 cm centrifugal contactors. The tests involved first loading the solvent (30 vol% TBP dissolved in n-dodecane) with U and Pu, then the Pu was stripped from the loaded solvent with a U(IV) solution (~50 mM) and the flowsheet conditions were adjusted such that some U partitioned into the Pu-containing product stream. The amount of U accompanying the Pu was monitored in real time using optical spectroscopic techniques coupled with chemometric modeling. Based on the real-time spectroscopic measurement of the U/Pu ratio, adjustments were made to the flowrate of the fresh TBP solvent phase used to scrub U from the aqueous Pu-containing product. This proved to be a very effective way to control the U/Pu mass ratio in the product.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

In Situ Monitoring and Kinetic Analysis of the Extraction of Nitric Acid by Tributyl Phosphate in n-Dodecane using Raman Spectroscopy

Understanding the fundamental rates of transfer and complex formation is crucial in maintaining optimal efficiency and effectivity in solvent extraction. Methodologies to effectively analyze solvent extraction systems are lacking in that they are commonly off-line. Thus, a method to effectively investigate solvent extraction systems in a Lewis cell using in situ Raman spectroscopy paired with chemometric modelling has been developed to allow for on-line analysis and monitoring. Kinetic parameters of interfacial mass transfer for the extraction of nitric acid by tributyl phosphate, a process crucial to used nuclear fuel reprocessing, were measured in by spectroscopic monitoring of both phases simultaneously in a two-phase solvent extraction system. Resulting concentration data, derived from a chemometric model using Raman spectra as the base set, allowed for the calculation of kinetic parameters in the system when paired with extraction time. The forward and reverse interfacial mass transfer coefficients, kf and kr, were determined for solutions that were process relevant and of pro-cess interest, where kf was calculated as 5.3 (± 0.3) × 10-3 cm min 1 and kr was calculated as 2.9 (± 0.2) × 10-2 cm min-1. The information obtained regarding solvent extraction parameters and transfer can be applied in the further study of systems of higher complexity involving complex formation and their transfer across a liquid:liquid interface.

extraction, interfacial transport, Lewis Cell, Liq↗

Micro-Raman technology to interrogate two-phase extraction on a microfluidic device

Microfluidic devices provide ideal environments to study solvent extraction. When droplets form and generate plug flow down the microfluidic channel, the device acts as a microreactor in which the kinetics of chemical reactions and interfacial transfer can be examined. Among the many benefits of microreactors is the ability to maintain small sample volumes, which is especially important when studying solvent extraction in harsh environments, such as in separations related to the nuclear fuel cycle. In solvent extraction, the efficiency of the process depends on complex formation and rates of transfer in biphasic systems. Thus, it is important to understand the kinetic parameters in an extraction system to maintain a high efficiency and effectivity of the process. Here we present a methodology that combines chemometric analysis with on-line micro-Raman spectroscopy to monitor biphasic extractions within a microfluidic device. This monitoring provided concentration measurements in both organic and aquoeus plugs as they flowed through the microfluidic channel. The biphasic system studied was comprised of HNO3 as the aqueous phase and 30 % (v/v) tributyl phosphate in n-dodecane comprised the organic phase, which simulated the Plutonium Uranium Redox EXtraction (PUREX) process. Using pre-equilibrated solutions (post extraction) the validity of the technique and methodology is illustrated. Following this validation, solutions that were not equilibrated were examined and the kinetics of interfacial mass transfer within the biphasic system were established. Results were compared to kinetics already determined on a macro scale to prove the efficacy of the technique

extraction, interfacial transport, liquid:liquid e↗