Search NASA⌕ Search

Engineering topics

Assanis, Dimitris

Publications and source records attributed to Assanis, Dimitris.

Enabling residential heating decarbonization through hydronic low-temperature thermal distribution using forced-air assistive devices

Space heating represents approximately one-tenth of the United States’ energy use and has a breadth of potential for emission reduction. An element of space heating, hydronic heat distribution methods, use water supply temperatures up to 82.2 °C (180 °F). However, this operating temperature can be incompatible with high-efficiency heat generation systems, which typically provide heating temperatures of up to 60 °C (140 °F). In this work, a low-cost retrofit solution is developed using experimentally validated computational tools by incorporating an airflow distributor that preferentially directs the airflow from a fan to enhance heat transfer over the finned-tube heat exchanger found in conventional baseboards. The same heat output of traditional baseboard heat distribution systems operating at higher water supply temperatures (71.1 – 82.2 °C) can also be achieved at lower temperatures (≤60 °C). Specifically, results indicate that the technology can produce more than a 46.7% improvement in the heat transfer output at temperatures as low as 60 °C (140 °F), effectively matching the same output range achieved by 71.1 – 82.2 °C (160–180 °F) water supply temperatures. An important benefit of this solution is that it utilizes the existing infrastructure as opposed to requiring the replacement of the entire distribution system. Additionally, this technology enables existing building infrastructure to be coupled with newer, high-efficiency heating systems such as condensing boilers, solar-thermal systems, and geothermal/air-to-water heat pumps that may produce lower water supply temperatures (60 °C). A geospatially resolved techno-economic and environmental analysis is completed and presented to further understand the equivalent carbon footprint of enabling higher efficiency heat generation systems with the improved efficiency heat distribution system disclosed. Using 2021 grid-average emission factors, an emission reduction of up to a 67.5% decrease (2658 kgCO 2 /yr) for a single-family home, depending on state and climate region, could be realized by replacing a traditional natural gas-fired boiler with an air-to-water heat pump coupled to the same high-temperature heat distribution system along with the low-cost retrofit solution. A complete CO 2 emission reduction of 6688 kgCO 2 /yr, depending on state and climate region, could be realized if all electricity is further renewably sourced. Thus, this study provides a possible pathway towards enabling the reduction of operational emissions in space heating.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Development and evaluation of a skeletal mechanism for EHN additized gasoline mixtures in large Eddy simulations of HCCI combustion

Advanced Low Temperature Combustion modes, such as the Sandia proposed Additive-Mixing Fuel Injection (AMFI), can unlock significant potential to boost fuel conversion efficiency and ultimately improve the energy conversion of internal combustion engines. This is a novel improved combustion process that is enabled by supplying small (<5%) variable amounts of autoignition improver to the fuel to enhance the engine operation and control. Common, diesel-fuel ignition-quality enhancing additive, 2-ethylexyl nitrate (EHN), is doped into gasoline to enable Sandia LTGC + AMFI combustion. This manuscript focuses on the development of a reduced sub-mechanism for EHN chemical kinetics at engine relevant conditions that is implemented into a skeletal mechanism for chemical kinetic studies of gasoline surrogate fuels. The mechanism validation utilized zero-dimensional numerical simulations and comparison to shock tube ignition-delay data of pure and EHN-doped n-heptane. Additional validation is presented with Homogeneous Charge Compression-Ignition (HCCI) engine data of pure and EHN-doped research-grade E10 gasoline. Then, the mechanism was deployed in a 3-D computational fluid dynamics (CFD) using Large Eddy Simulations (LES) to model the HCCI engine experiments of 0.4% vol EHN additized E10 gasoline at several equivalence ratios. Simulations showed a very good performance of the mechanism, and the model accurately reproduced (a) the ignition point, (b) combustion phasing, (c) combustion duration, and (d) the peak of the heat release rates of the engine experiments. The results show that EHN promotes Low-Temperature Heat Release, ultimately driving the gasoline to autoignite at thermodynamic conditions where the fuel would not otherwise ignite. Overall, this work demonstrates a viable reduced chemical-kinetic mechanism for EHN and shows that it can be combined with a skeletal gasoline mechanism for CFD-LES analysis of well-mixed LTGC that matches well with experimental results. The CFD-LES analysis also shows the spatial distribution of EHN-fuel interactions that control the autoignition throughout the combustion chamber.

Guleria, Gaurav↗

A Double-Wiebe Function for Reactivity Controlled Compression Ignition Combustion Using Reformate Diesel

Abstract Reactivity controlled compression ignition (RCCI) combustion has previously been proposed as a method to achieve high fuel conversion efficiency and reduce engine emissions. A single-fuel RCCI combustion strategy can have decreased fuel system complexity by using a reformate fuel for port fuel injection and the parent fuel (diesel) for direct injection. This paper presents a one-dimensional computational model of a compression ignition engine with single-fuel RCCI. A Wiebe function is used to predict the combustion process by representing the mass fraction burned (MFB) on a crank angle resolved basis. One single-Wiebe function (SWF) and two double-Wiebe functions(DWFs) were fitted to experimentally derive MFB data using the least-square method. The fitted results were compared with MFBs calculated from experimental data to verify the accuracy. The SWF did not fully capture the MFB curve with high fidelity while the detailed DWF captured the MFB curve within a root mean square error of 1.4%. The reduced double-Wiebe function (RDWF) also resulted in a predicted combustion profile with similar accuracy. Hence, the RDWF was used in a GT-power thermodynamic study to understand the effects of the low-temperature heat release (LTHR) fraction and combustion phasing on combustion characteristics. At optimum phasing of 5–10 crank angle degree after the top dead center, increasing the LTHR fraction from 20% to 60% resulted in the fuel conversion efficiency increasing from 39.5% to 41.1%, thus suggesting that the reformate fuel-based RCCI strategy is viable to unlock improved combustion performance.

Energy & Fuels↗