Engineering topics

Atkins, Harold L.

Publications and source records attributed to Atkins, Harold L..

17 records

NASA NTRS2018

Convergence Analysis of Turbulent Flow Solutions

Data from the "Turbulence Modeling Resource" website for turbulent flow over an NACA-0012 airfoil is analyzed to determine the convergence behavior of three second-order CFD (Computational Fluid Dynamics) codes: CFL3D (Computational Fluids Lab 3 Dimensional flow solver), FUN3D (Fully Unstructured Navier-stokes flow solver), and TAU (German Aerospace Center (DLR) 2 dimensional code for unstructured hybrid grids solving the Reynolds-Averaged Navier-Stokes equations or the Euler equations). The convergence of both integrated properties and pointwise data are examined. Several different methods for estimating errors and computing convergence rates are compared. A high-order extension to the Richardson extrapolation is developed that improves the accuracy of the mesh limit values and provides a quantitative estimate of the threshold of the asymptotic regime. The coefficient of total drag exhibits second-order convergence for all three codes, and convergence is monotone over a sequence of 7 grids. Other force coefficients are not so well behaved. The convergence rates of the viscous component of drag on the three nest grids ranges from 3:0 for CFL3D to 1:0 for FUN3D. The three codes are converging to similar but not identical solutions. The largest differences between the codes are in the coefficient of lift for which the difference between CFL3D and FUN3D is greater than 10 (sup minus 4). The best agreement occurs in the viscous component of drag, which is the only force component for which all three codes are converging towards each other at a rate of second-order. The agreement between the two unstructured grid codes is good with all properties except lift converging towards common values at a rate of second-order. No one code was universally better than the other. The TAU code has the lowest error in total drag, FUN3D has the lowest error in lift, and CFL3D has the lowest error in the viscous component of drag.

Atkins, Harold L.↗

NASA NTRS2016

Status of Computational Aerodynamic Modeling Tools for Aircraft Loss-of-Control

A concerted effort has been underway over the past several years to evolve computational capabilities for modeling aircraft loss-of-control under the NASA Aviation Safety Program. A principal goal has been to develop reliable computational tools for predicting and analyzing the non-linear stability & control characteristics of aircraft near stall boundaries affecting safe flight, and for utilizing those predictions for creating augmented flight simulation models that improve pilot training. Pursuing such an ambitious task with limited resources required the forging of close collaborative relationships with a diverse body of computational aerodynamicists and flight simulation experts to leverage their respective research efforts into the creation of NASA tools to meet this goal. Considerable progress has been made and work remains to be done. This paper summarizes the status of the NASA effort to establish computational capabilities for modeling aircraft loss-of-control and offers recommendations for future work.

Frink, Neal T.↗

NASA NTRS2013

High-Order Simulation of Induced Disturbance in a Mach 6 Boundary Layer

Simulations of the early evolution of induced unstable disturbances in a Mach 6 hypersonic boundary layer are presented for the purposes of validating a high-order discontinuous Galerkin Navier-Stokes simulation code. The simulations are modeled after experiments performed in the Boeing/AFOSR Mach-6 Quiet Tunnel at Purdue University. In these experiments, a forcing mechanism was employed to induce reproducible disturbances in a hypersonic boundary layer providing for the controlled study of the growth and breakdown of these disturbances into turbulent spots. Simulations revealed that the form and strength of the excitation can greatly influence the growth of the disturbance. In particular, at large forcing amplitude, the simulated forcing produces large advecting transients that appear to enhance the growth of the wave packet, relative to that of low amplitude forcing. Simulation results with large amplitude forcing agree well with experimental results while results from low amplitude forcing agree with linear stability theory.

Atkins, Harold L.↗

NASA NTRS2011

Robust and Accurate Shock Capturing Method for High-Order Discontinuous Galerkin Methods

A simple yet robust and accurate approach for capturing shock waves using a high-order discontinuous Galerkin (DG) method is presented. The method uses the physical viscous terms of the Navier-Stokes equations as suggested by others; however, the proposed formulation of the numerical viscosity is continuous and compact by construction, and does not require the solution of an auxiliary diffusion equation. This work also presents two analyses that guided the formulation of the numerical viscosity and certain aspects of the DG implementation. A local eigenvalue analysis of the DG discretization applied to a shock containing element is used to evaluate the robustness of several Riemann flux functions, and to evaluate algorithm choices that exist within the underlying DG discretization. A second analysis examines exact solutions to the DG discretization in a shock containing element, and identifies a "model" instability that will inevitably arise when solving the Euler equations using the DG method. This analysis identifies the minimum viscosity required for stability. The shock capturing method is demonstrated for high-speed flow over an inviscid cylinder and for an unsteady disturbance in a hypersonic boundary layer. Numerical tests are presented that evaluate several aspects of the shock detection terms. The sensitivity of the results to model parameters is examined with grid and order refinement studies.

Atkins, Harold L.↗

NASA NTRS2010

CFD Assessment of Aerodynamic Degradation of a Subsonic Transport Due to Airframe Damage

A computational study is presented to assess the utility of two NASA unstructured Navier-Stokes flow solvers for capturing the degradation in static stability and aerodynamic performance of a NASA General Transport Model (GTM) due to airframe damage. The approach is to correlate computational results with a substantial subset of experimental data for the GTM undergoing progressive losses to the wing, vertical tail, and horizontal tail components. The ultimate goal is to advance the probability of inserting computational data into the creation of advanced flight simulation models of damaged subsonic aircraft in order to improve pilot training. Results presented in this paper demonstrate good correlations with slope-derived quantities, such as pitch static margin and static directional stability, and incremental rolling moment due to wing damage. This study further demonstrates that high fidelity Navier-Stokes flow solvers could augment flight simulation models with additional aerodynamic data for various airframe damage scenarios.

Frink, Neal T.↗

NASA NTRS2009

Super-convergence of Discontinuous Galerkin Method Applied to the Navier-Stokes Equations

The practical benefits of the hyper-accuracy properties of the discontinuous Galerkin method are examined. In particular, we demonstrate that some flow attributes exhibit super-convergence even in the absence of any post-processing technique. Theoretical analysis suggest that flow features that are dominated by global propagation speeds and decay or growth rates should be super-convergent. Several discrete forms of the discontinuous Galerkin method are applied to the simulation of unsteady viscous flow over a two-dimensional cylinder. Convergence of the period of the naturally occurring oscillation is examined and shown to converge at 2p+1, where p is the polynomial degree of the discontinuous Galerkin basis. Comparisons are made between the different discretizations and with theoretical analysis.

Atkins, Harold L.↗

NASA NTRS2005

Simulation of Unsteady Flows Using an Unstructured Navier-Stokes Solver on Moving and Stationary Grids

We apply an unsteady Reynolds-averaged Navier-Stokes (URANS) solver for unstructured grids to unsteady flows on moving and stationary grids. Example problems considered are relevant to active flow control and stability and control. Computational results are presented using the Spalart-Allmaras turbulence model and are compared to experimental data. The effect of grid and time-step refinement are examined.

Biedron, Robert T.↗

NASA NTRS2003

A Discrete Analysis of Non-reflecting Boundary Conditions for Discontinuous Galerkin Method

We present a discrete analysis of non-reflecting boundary conditions for the discontinuous Galerkin method. The boundary conditions considered in this paper include the recently proposed Perfectly Matched Layer absorbing boundary condition for the linearized Euler equation and two non-reflecting boundary conditions based on the characteristic decomposition of the flux on the boundary. The analyses for the three boundary conditions are carried out in a unifled way. In each case, eigensolutions of the discrete system are obtained and applied to compute the numerical reflection coefficients of a specified out-going wave. The dependencies of the reflections at the boundary on the out-going wave angle and frequency as well as the mesh sizes arc? studied. Comparisons with direct numerical simulation results are also presented.

Hu, Fang Q.↗

NASA NTRS2002

Opportunities for Breakthroughs in Large-Scale Computational Simulation and Design

Opportunities for breakthroughs in the large-scale computational simulation and design of aerospace vehicles are presented. Computational fluid dynamics tools to be used within multidisciplinary analysis and design methods are emphasized. The opportunities stem from speedups and robustness improvements in the underlying unit operations associated with simulation (geometry modeling, grid generation, physical modeling, analysis, etc.). Further, an improved programming environment can synergistically integrate these unit operations to leverage the gains. The speedups result from reducing the problem setup time through geometry modeling and grid generation operations, and reducing the solution time through the operation counts associated with solving the discretized equations to a sufficient accuracy. The opportunities are addressed only at a general level here, but an extensive list of references containing further details is included. The opportunities discussed are being addressed through the Fast Adaptive Aerospace Tools (FAAST) element of the Advanced Systems Concept to Test (ASCoT) and the third Generation Reusable Launch Vehicles (RLV) projects at NASA Langley Research Center. The overall goal is to enable greater inroads into the design process with large-scale simulations.

Alexandrov, Natalia↗

NASA NTRS2002

Slat Cove Noise Modeling: A Posteriori Analysis of Unsteady RANS Simulations

A companion paper by Khorrami et al demonstrates the feasibility of simulating the (nominally) self-sustained, large-scale unsteadiness within the leading-edge slat-cove region of multi-element airfoils using unsteady Reynolds-Averaged Navier-Stokes (URANS) equations, provided that the turbulence production term in the underlying two-equation turbulence model is switched off within the cove region. In conjunction with a FfowesWilliams-Hawkings solver, the URANS computations were shown to capture the dominant portion of the acoustic spectrum attributed to slat noise, as well as reproducing the increased intensity of slat cove motions (and, correspondingly, far-field noise as well) at the lower angles of attack. This paper examines that simulation database, augmented by additional simulations, with the objective of transitioning this apparent success to aeroacoustic predictions in an engineering context. As a first step towards this goal, the simulated flow and acoustic fields are compared with experiment and simplified analytical model. Rather intense near-field fluctuations in the simulated flow are found to be associated with unsteady separation along the slat bottom surface, relatively close to the slat cusp. Accuracy of the laminar-cove simulations in this near-wall region is raised to be an open issue. The adjoint Green's function approach is also explored in an attempt to identify the most efficient noise source locations.

Choudhari, Meelan↗

NASA NTRS2002

The Current Status of Unsteady CFD Approaches for Aerodynamic Flow Control

An overview of the current status of time dependent algorithms is presented. Special attention is given to algorithms used to predict fluid actuator flows, as well as other active and passive flow control devices. Capabilities for the next decade are predicted, and principal impediments to the progress of time-dependent algorithms are identified.

Carpenter, Mark H.↗

NASA NTRS2000

An Application of the Quadrature-Free Discontinuous Galerkin Method

The process of generating a block-structured mesh with the smoothness required for high-accuracy schemes is still a time-consuming process often measured in weeks or months. Unstructured grids about complex geometries are more easily generated, and for this reason, methods using unstructured grids have gained favor for aerodynamic analyses. The discontinuous Galerkin (DG) method is a compact finite-element projection method that provides a practical framework for the development of a high-order method using unstructured grids. Higher-order accuracy is obtained by representing the solution as a high-degree polynomial whose time evolution is governed by a local Galerkin projection. The traditional implementation of the discontinuous Galerkin uses quadrature for the evaluation of the integral projections and is prohibitively expensive. Atkins and Shu introduced the quadrature-free formulation in which the integrals are evaluated a-priori and exactly for a similarity element. The approach has been demonstrated to possess the accuracy required for acoustics even in cases where the grid is not smooth. Other issues such as boundary conditions and the treatment of non-linear fluxes have also been studied in earlier work This paper describes the application of the quadrature-free discontinuous Galerkin method to a two-dimensional shear layer problem. First, a brief description of the method is given. Next, the problem is described and the solution is presented. Finally, the resources required to perform the calculations are given.

Lockard, David P.↗

NASA NTRS1999

Efficient Implementations of the Quadrature-Free Discontinuous Galerkin Method

The efficiency of the quadrature-free form of the dis- continuous Galerkin method in two dimensions, and briefly in three dimensions, is examined. Most of the work for constant-coefficient, linear problems involves the volume and edge integrations, and the transformation of information from the volume to the edges. These operations can be viewed as matrix-vector multiplications. Many of the matrices are sparse as a result of symmetry, and blocking and specialized multiplication routines are used to account for the sparsity. By optimizing these operations, a 35% reduction in total CPU time is achieved. For nonlinear problems, the calculation of the flux becomes dominant because of the cost associated with polynomial products and inversion. This component of the work can be reduced by up to 75% when the products are approximated by truncating terms. Because the cost is high for nonlinear problems on general elements, it is suggested that simplified physics and the most efficient element types be used over most of the domain.

Lockard, David P.↗

NASA NTRS1999

A High-Order Method Using Unstructured Grids for the Aeroacoustic Analysis of Realistic Aircraft Configurations

A method for the prediction of acoustic scatter from complex geometries is presented. The discontinuous Galerkin method provides a framework for the development of a high-order method using unstructured grids. The method's compact form contributes to its accuracy and efficiency, and makes the method well suited for distributed memory parallel computing platforms. Mesh refinement studies are presented to validate the expected convergence properties of the method, and to establish the absolute levels of a error one can expect at a given level of resolution. For a two-dimensional shear layer instability wave and for three-dimensional wave propagation, the method is demonstrated to be insensitive to mesh smoothness. Simulations of scatter from a two-dimensional slat configuration and a three-dimensional blended-wing-body demonstrate the capability of the method to efficiently treat realistic geometries.

Atkins, Harold L.↗

NASA NTRS1995

Application of essentially nonoscillatory methods to aeroacoustic flow problems

A finite-difference essentially nonoscillatory (ENO) method has been applied to several of the problems prescribed for the workshop sponsored jointly by the Institute for Computer Applications in Science and Engineering and by NASA Langley Research Center entitled 'Benchmark Problems in Computational Aeroacoustics'. The workshop focused on computational challenges specific to aeroacoustics. Among these are long-distance propagation of a short-wavelength disturbance, propagation of small-amplitude disturbances, and nonreflective boundary conditions. The shock capturing-capability inherent to the ENO method effectively eliminates oscillations near shock waves without the need to add and tune dissipation or filter terms. The method-of-lines approach allows the temporal and spatial operators to be chosen separately in accordance with the demands of a particular problem. The ENO method was robust and accurate for all problems in which the propagating wave was resolved with 8 or more points per wavelength. The finite-wave-model boundary condition, a local nonlinear acoustic boundary condition, performed well for the one-dimensional problems. The buffer-domain approach performed well for the two-dimensional test problem. The amplitude of nonphysical reflections were less than 1 percent of the exiting wave's amplitude.

Atkins, Harold L.↗

NASA NTRS1993

Time-accurate Navier-Stokes calculations with multigrid acceleration

A numerical scheme to solve the unsteady Navier-Stokes equations is described. The scheme is implemented by modifying the multigrid-multiblock version of the steady Navier-Stokes equations solver, TLNS3D. The scheme is fully implicit in time and uses TLNS3D to iteratively invert the equations at each physical time step. The design objective of the scheme is unconditional stability (at least for first- and second-order discretizations of the physical time derivatives). With unconditional stability, the choice of the time step is based on the physical phenomena to be resolved rather than limited by numerical stability which is especially important for high Reynolds number viscous flows, where the spatial variation of grid cell size can be as much as six orders of magnitude. An analysis of the iterative procedure and the implementation of this procedure in TLNS3D are discussed. Numerical results are presented to show both the capabilities of the scheme and its speed up relative to the use of global minimum time stepping. Reductions in computational times of an order of magnitude are demonstrated.

Melson, N. Duane↗

NASA NTRS1993

Time-accurate Navier-Stokes calculations with multigrid acceleration

An efficient method for calculating unsteady flows is presented, with emphasis on a modified version of the thin-layer Navier-Stokes equations. Fourier stability analysis is used to illustrate the effect of treating the source term implicitly instead of explicity, as well as to illustrate other algorithmic choices. A 2D circular cylinder (with a Reynolds number of 1200 and a Mach number of 0.3) is calculated. The present scheme requires only about 10 percent of the computer time required by global minimum time stepping.

Melson, N. D.↗