Search NASA⌕ Search

Engineering topics

Awni, Rasha A.

Publications and source records attributed to Awni, Rasha A..

15 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Water-Assisted Lift-Off Process for Flexible CdTe Solar Cells

In recent years, various lift-off methods have been developed to fabricate lightweight and flexible cadmium telluride (CdTe)-based solar cells. In this work, we report flexible cadmium sulfide (CdS)/CdTe solar cells using a water-assisted lift-off approach. Here we demonstrate that an additional cadmium chloride treatment for the CdS film is critical to improve the grain size of CdS and the post-deposited CdTe film and the electron conductivity of the CdS film. As a result, the quality of the CdS/CdTe front junction is significantly improved with reduced nonradiative recombination. Finally, our lightweight and flexible polycrystalline CdTe solar cells demonstrate a champion power conversion efficiency of 12.6%.

14 SOLAR ENERGY↗
DOE OSTI2022

Post‐Annealing Treatment on Hydrothermally Grown Antimony Sulfoselenide Thin Films for Efficient Solar Cells

Herein, antimony sulfoselenide (Sb 2 (S, Se) 3 ) thin‐film solar cells are fabricated by a hydrothermal method followed by a post‐deposition annealing process at different temperatures and the impact of the annealing temperature on the morphological, structural, optoelectronic, and defect properties of the hydrothermally grown Sb 2 (S, Se) 3 films is investigated. It is found that a proper annealing temperature leads to high‐quality Sb 2 (S, Se) 3 films with large crystal grains, high crystallinity, preferred crystal orientation, smooth and uniform morphology, and reduced defect density. These results show that suppressing deep‐level defects is crucial to enhance solar cell performance. After optimizing the annealing process, Sb 2 (S, Se) 3 solar cells with an improved power conversion efficiency 2.04 to 8.48% are obtained.

14 SOLAR ENERGY↗
DOE OSTI2022

20%-efficient polycrystalline Cd(Se,Te) thin-film solar cells with compositional gradient near the front junction

Bandgap gradient is a proven approach for improving the open-circuit voltages (V OC s) in Cu(In,Ga)Se 2 and Cu(Zn,Sn)Se 2 thin-film solar cells, but has not been realized in Cd(Se,Te) thin-film solar cells, a leading thin-film solar cell technology in the photovoltaic market. Here, we demonstrate the realization of a bandgap gradient in Cd(Se,Te) thin-film solar cells by introducing a Cd(O,S,Se,Te) region with the same crystal structure of the absorber near the front junction. The formation of such a region is enabled by incorporating oxygenated CdS and CdSe layers. We show that the introduction of the bandgap gradient reduces the hole density in the front junction region and introduces a small spike in the band alignment between this and the absorber regions, effectively suppressing the nonradiative recombination therein and leading to improved VOCs in Cd(Se,Te) solar cells using commercial SnO 2 buffers. A champion device achieves an efficiency of 20.03% with a V OC of 0.863 V.

14 SOLAR ENERGY↗
DOE OSTI2022

Reduced Recombination and Improved Performance of CdSe/CdTe Solar Cells due to Cu Migration Induced by Light Soaking

The performance of CdTe solar cells has advanced impressively in recent years with the incorporation of Se. Instabilities associated with light soaking and copper reorganization have been extensively examined for the previous generation of CdS/CdTe solar cells, but instabilities in Cu-doped Se-alloyed CdTe devices remain relatively unexplored. In this work, we fabricated a range of CdSe/CdTe solar cells by sputtering CdSe layers with thicknesses of 100, 120, 150, 180, and 200 nm on transparent oxide-coated glass and then depositing CdTe by close-spaced sublimation. After CdCl 2 annealing, Cu-doping, and back metal deposition, a variety of analyses were performed both before and after light soaking to understand the changes in device performance. The device efficiency was degraded with light soaking in most cases, but devices fabricated with a CdSe layer thickness of 120 nm showed reasonably good efficiency initially (13.5%) and a dramatic improvement with light soaking (16.5%). Here, the efficiency improvement is examined within the context of Cu ion reorganization that is well known for CdS/CdTe devices. Low-temperature photoluminescence data and V oc versus temperature measurements indicate a reduction in nonradiative recombination due to the passivation of defects and defect complexes in the graded CdSe x Te 1–x layer.

CdSexTe1−x↗
DOE OSTI2021

Templated Growth and Passivation of Vertically Oriented Antimony Selenide Thin Films for High-Efficiency Solar Cells in Substrate Configuration

Antimony selenide (Sb 2 Se 3 ) is a promising low-cost photovoltaic material with a 1D crystal structure. The grain orientation and defect passivation play a critical role in determining the performance of polycrystalline Sb 2 Se 3 thin-film solar cells. In this work, a seed layer is introduced on a molybdenum (Mo) substrate to template the growth of a vertically oriented, columnar Sb 2 Se 3 absorber layer by closed space sublimation. By controlling the grain orientation and compactness of the Sb 2 Se 3 seeds, obtain high-quality Sb 2 Se 3 absorber layers with passive Sb 2 Se 3 /Mo interfaces is obtained, which in turn improve the transport of photoexcited charge carriers through the absorber layer and its interfaces. Post-deposition annealing of absorber layers in ambient air is further utilized to passivate the defects in Sb 2 Se 3 and enhance the quality of the front heterojunction. As a result of systematic processing optimization, Sb 2 Se 3 planar heterojunction solar cells are fabricated in substrate configuration with a champion power conversion efficiency of 8.5%.

14 SOLAR ENERGY↗
DOE OSTI2021

Copper iodide nanoparticles as a hole transport layer to CdTe photovoltaics: 5.5 % efficient back-illuminated bifacial CdTe solar cells

We report the role of copper iodide (CuI) nanoparticles (NPs) as a hole transport layer (HTL) in cadmium sulfide/cadmium telluride (CdS/CdTe) photovoltaics. These CuI NPs were prepared using solution processing at room temperature and used to fabricate monofacial and bifacial CdTe solar cells with different back contacts. Using CuI/Au as the back contact, the device efficiency reached to 14.8% with outstanding fill factor (FF) of 79.2%. Replacing the gold (Au) electrode with sputtered transparent indium tin oxide (ITO), a CuI/ITO back contact yielded photoconversion efficiencies (PCEs) of 11.6% and 5.5% under front and back illumination respectively. Bifacial devices (CdTe/ITO) without the CuI NP HTL have an efficiency of 7.0% and 1.0% for front and back illumination, respectively. For CuI/ITO, a current collection of 12.0 mAcm -2 was observed upon back illumination which significantly improved over an ITO-only back contact (5.0 mAcm -2 ). The PCE obtained from back illumination was enhanced when using CuI NPs as the HTL due to the reduced back barrier height, and improved back interface as determined by temperature dependent current vs. voltage characteristics and impedance spectroscopy analysis. The improvement in device performance of the bifacial configuration is a significant step forward toward realizing thin film photovoltaic modules which harvest energy incident on the rear of the module.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Low-temperature and effective ex situ group V doping for efficient polycrystalline CdSeTe solar cells

CdTe solar cell technology is one of the lowest-cost methods of generating electricity in the solar industry, benefiting from fast CdTe absorber deposition, CdCl 2 treatment and Cu doping. However, Cu doping has low photovoltage and issues with instability. Doping group V elements into CdTe is therefore a promising route to address these challenges. Although high-temperature in situ group V doped CdSeTe devices have demonstrated efficiencies exceeding 20%, they face obstacles including post-deposition doping activation processes, short carrier lifetimes and low activation ratios. Here, we demonstrate low-temperature and effective ex situ group V doping for CdSeTe solar cells using group V chlorides. For AsCl 3 doped CdSeTe solar cells, the dopant activation ratio can be 5.88%, hole densities reach >2 × 10 15 cm -3 and carrier lifetime is longer than 20 ns. Thus, ex situ As doped CdSeTe solar cells show open-circuit voltages ~863 mV, compared to the highest open-circuit voltage of 852 mV for Cu doped CdSeTe solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

On the design and performance of InGaN/Si double-junction photocathodes

Via a combined theoretical and experimental study, we have investigated the synthesis and performance characteristics of InGaN/Si double-junction photoelectrochemical (PEC) water splitting devices, which promise a theoretical solar-to-hydrogen conversion efficiency ~30% under AM 1.5G one-sun illumination. The double-junction photocathodes consist of a p + -InGaN top light absorber and a Si bottom p-n junction, which are connected through a nanowire tunnel junction. The effect of indium composition of the top light absorber as well as the impact of p-type Mg dopant incorporation on the PEC performance was studied. Experimentally, the sample with 32% indium composition showed a maximum photocurrent density of ~9 mA/cm 2 at 0.4 mV vs reverse hydrogen electrode (RHE) with applied bias photon-to-current efficiency (ABPE) of ~9.5%. An optimum p-type doping level ~1 × 10 17 cm -3 was also identified, which results in the best device performance as a result of optimum surface band bending as well as vertical charge carrier (hole) transport. These results also show a good agreement with our theoretical analysis. This work provides significant insights in advancing the design and development of high efficiency PEC devices for artificial photosynthesis using industry ready materials, e.g., Si and GaN, to achieve large-scale, low-cost onsite hydrogen fuel production.

42 ENGINEERING↗
DOE OSTI2021

Enabling bifacial thin film devices by developing a back surface field using Cu x AlO y

Bifacial solar cells have the potential to increase the energy yield per unit area over traditional monofacial devices without significant added cost, driving $/kWh costs lower and accelerating the adoption of solar photovoltaics. However, the performance of bifacial thin film solar cells significantly lags that achieved by crystalline silicon cells. Here we incorporate wide bandgap Cu x AlO y as a back buffer layer for CdTe devices and achieve a backside illuminated device with high current density and high fill factor. Moreover, these values remain nearly constant even as the absorber layer thickness changes, indicating that a fully-depleted device is not required for efficient charge collection. We show that this response is indicative of a back surface field, albeit with a persistent high back surface recombination velocity. By managing electron reflection, we achieved a backside illumination conversion efficiency of 7.1% and bifaciality of 0.55 for a 3.3 µm CdTe device and 8.0% and 0.62 for a 2 µm device. Future improvements can be made by identifying and incorporating a passivation material that reduces the back surface recombination velocity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Semi-transparent p-type barium copper sulfide as a back contact interface layer for cadmium telluride solar cells

Optically transparent p-type materials play a critical role in transparent electronics including photovoltaic (PV) devices. P-type sulfide materials offer an alternative to oxides for PV application due to improved hole transport properties. Here, we report the solution-based synthesis of earth-abundant p-type transparent conducting barium copper sulfide (α-BaCu 4 S 3 , BCS) thin films. These films were characterized using scanning electron microscopy, X-ray diffraction, UV–Vis–NIR spectrophotometry, Raman spectroscopy, and spectroscopic ellipsometry. BCS films of ~100 nm thickness transmit >70% of visible light. We report on tests of the hole transport properties of these BCS films for cadmium telluride (CdTe) photovoltaics, finding that the BCS deposition process forms a beneficial tellurium (Te) rich surface on CdTe by selectively removing Cd from the surface. Based on our study, the BCS interface layer plays dual functions for CdTe PV devices as a hole transport material and as an etchant, enhancing the resulting device performance. We observed a significant increase in open-circuit voltage of CdTe solar cells with the BCS buffer layer. Furthermore, we discuss semitransparent CdTe solar cells with BCS as a hole transport layer and indium tin oxide as a finishing electrode. Semitransparent CdTe solar cells shows 13.3% conversion efficiency for the front side illumination and 1.2% efficiency for back side illumination, indicating high recombination of charge carriers generated close to the rear CdTe/BCS/ITO contact.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Arylammonium-Assisted Reduction of the Open-Circuit Voltage Deficit in Wide-Bandgap Perovskite Solar Cells: The Role of Suppressed Ion Migration

Surface treatment using large alkyl/aryl ammonium cations has demonstrated reduced open-circuit voltage (V OC ) deficits in perovskite solar cells (PSCs), but the origin of the improvements has been vaguely attributed to defect passivation. Here, we combine the microscopic probing of the local electrical properties, thermal admittance spectroscopic analysis, and first principles calculations to elucidate the critical role of arylammonium interface layers on suppressing the ion migration in wide-bandgap (WBG) PSCs. Our results reveal that arylammonium surface treatment using phenethylammonium iodide increases the activation energy barrier for ion migration on the surface, which suppresses the accumulation of charge defects at surface and grain boundaries (GBs), leading to reduced dark saturation current density in WBG PSCs. Furthermore, with device optimization, our champion 1.73-eV PSC delivers a power conversion efficiency of 19.07% with a V OC of 1.25 V, achieving a V OC -deficit of 0.48 V.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Influence of Charge Transport Layers on Capacitance Measured in Halide Perovskite Solar Cells

Capacitance-based techniques were previously used to measure the electrical properties of halide perovskite solar cells (PSCs) such as defect activation energy and density, carrier concentration, and dielectric constant, which provide key information for evaluating the device performance. Herein, we show that capacitance-based techniques cannot be used to reliably analyze the properties of defects in the perovskite layer or at its interface, since the high-frequency capacitance signature is due to the response of charge carriers in the hole-transport layer (HTL). For HTL-free PSCs, the high-frequency capacitance can be considered as the geometric capacitance for analyzing the dielectric constant of the perovskite layer, since there is no trapping and de-trapping of charge carriers in the perovskite layer. We also find that the low-frequency capacitance signature can be used to calculate the activation energy of the ionic conductivity of the perovskite layer, but the overlapping effects with charge transport materials must be avoided.

14 SOLAR ENERGY↗